ASTM E1045-2000(2016) 2407 Standard Specification for Pipet Sahli Hemoglobin《沙式血红蛋白吸管的标准规格》.pdf

《ASTM E1045-2000(2016) 2407 Standard Specification for Pipet Sahli Hemoglobin《沙式血红蛋白吸管的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1045-2000(2016) 2407 Standard Specification for Pipet Sahli Hemoglobin《沙式血红蛋白吸管的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1045 00 (Reapproved 2016)Standard Specification forPipet, Sahli Hemoglobin1This standard is issued under the fixed designation E1045; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number

2、 in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers reusable pipets calibrated “tocontain” 20 cmm of whole blood and used for hemoglobindeterminations.1.2 The values s

3、tated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.2. Referenced Documents2.1 ASTM Standards:2E920 Specification for Commercially Packaged LaboratoryApparatusE921 Specification for Export Packaged Laboratory Appa-ratusE1133 Practice for Perfor

4、mance Testing of Packaged Labo-ratory Apparatus for United States Government Procure-mentsE1157 Specification for Sampling and Testing of ReusableLaboratory Glassware3. Materials3.1 The pipets shall be made of common spirit bore whiteback tubing or of clear glass with a white stripe applied to theou

5、ter surface of the tubing.4. Design4.1 ShapePipets shall be straight and of one-piece con-struction. Any cross section of a pipet taken in a planeperpendicular to the longitudinal axis should be circular.4.2 Delivery TipsDelivery tips shall be made with agradual or concave taper to a length of 10 to

6、 25 mm. The tipend shall be ground and tapered with fine abrasive, or fire-polished. Dimensions of the delivery tip shall be as specified inFig. 1.4.3 The top of the pipet shall be ground to a taper or formedto a funnel shape according to the dimensions specified in Fig.1.5. Markings5.1 Graduation L

7、ineThe pipet shall have one graduationline located 20 cmm from the pipet tip. The graduation lineshall be located on the clear portion of the tubing and shallextend at least two thirds around the pipet and not exceed 0.4mm in width.5.2 Volumetric DesignationThe pipet shall be marked20CMM on the clea

8、r portion of the tubing with the markingslocated approximately 5 mm above the graduation line.5.3 IdentificationEach pipet shall be marked with themanufacturers name or trademark on the white stripe portionof the pipet. Catalog number markings are optional. Allmarkings shall be permanently fused ont

9、o the pipet. Themarkings shall be amber or black in color. When tested inaccordance to 6.3, the pigmentation shall not discolor. Theappearance of the markings, when viewed by the eye undernormal room lighting, shall be the same before and aftertesting.5.4 Capacity DeviationSahli Hemoglobin pipets ar

10、e madewith maximum capacity deviation of 61.0 % or 62.0 %. Theselected capacity deviation shall be marked on the clear orwhite stripe portion of the pipet. The capacity of the pipet shallbe within the selected capacity deviation marked on the pipetwhen tested as specified in 6.2.6. Testing6.1 Capaci

11、ty TestThe capacity of the pipet shall bedetermined by means of using distilled water and a weighingdevice with weight sensitivity not less than 0.001 mg.6.1.1 The pipet shall be thoroughly cleaned, dried, andallowed to adjust to room temperature.6.1.2 The pipet shall be weighed and the weight recor

12、ded.6.1.3 The pipet shall be filled to the calibration line withdistilled water and weighed, and the weight recorded.6.1.4 The recorded weight of the clean and dry pipet shall besubtracted from the recorded weight of the distilled water-filledpipet providing the observed volumetric capacity (Vc)ofth

13、epipet in grams.1This specification is under the jurisdiction of ASTM Committee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onLaboratory Ware and Supplies.Current edition approved Sept. 1, 2016. Published September 2016. Originallyapproved in 1985. Last previou

14、s edition approved in 2010 as E1045 00 (2010).DOI: 10.1520/E1045-00R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe AST

15、M website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.1.5 The observed volumetric capacity (Vt) shall then becorrected to actual volumetric capacity at 20C (Vc), deter-mined by:Vc5Vt11a t 2 20C!(1)where:Vt= observed volumetric c

16、apacity at t C, grams,Vc= corrected volumetric capacity at 20C,a = coefficient of cubical expansion of pipetglass, = 0.000072C 0.000084C (dependent uponsource of material), andt = temperature recorded during weighing, C.6.2 Capacity DeviationThe capacity deviation of the pipetis the difference betwe

17、en the stated capacity V1and thecorrected observed capacity Vc, and is determined by thefollowing expression:Capacity deviation, % 5100Vc2 V1!V1(2)6.3 Pigmentation TestPrepare a fresh chromic acid clean-ing solution by combining 200 g of solution dichromate (Na2Cr2O72H2O), 1000 mLof water, and 1500

18、mLof sulfuric acid(H2SO4, ACS Reagent95 to 98 %). Immerse the pipets inthe chromic acid solution. Let stand at room temperature (20 to25C) for 15 min. Remove the pipets from the solution andthoroughly rinse in distilled water. Dry the pipets by rubbingvigorously, 5 to 10 strokes, with a laboratory c

19、loth or tissue.The appearance of the markings should be the same as beforethe test, when judged by the eye under normal room lighting.6.4 Strain Free TestThe pipets shall be free from strainwhen viewed under a polariscope.7. Sampling and Testing7.1 See Specification E1157.8. Packaging8.1 Select one

20、from Specifications E920, E921 or PracticeE1133.9. Keywords9.1 disposal; glass; tube; WestergrenFIG. 1 Pipet, Sahli HemoglobinE1045 00 (2016)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of thi

21、s standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five yea

22、rs andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical commit

23、tee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1942

24、8-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 00 (2016)3