ASTM E11-2009 752 Standard Specification for Wire Cloth and Sieves for Testing Purposes《试验用金属丝筛布筛分装置的标准规范》.pdf

《ASTM E11-2009 752 Standard Specification for Wire Cloth and Sieves for Testing Purposes《试验用金属丝筛布筛分装置的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM E11-2009 752 Standard Specification for Wire Cloth and Sieves for Testing Purposes《试验用金属丝筛布筛分装置的标准规范》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E 11 09Standard Specification forWoven Wire Test Sieve Cloth and Test Sieves1This standard is issued under the fixed designation E 11; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision. A number

2、 in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This document specifies the technical requirements for;the w

3、oven wire test sieve cloth (sieve cloth) used in test sieves,the construction of test sieves, standard and non-standard testsieve frame sizes, and test procedures used to inspect sievecloth and the test sieves. This Specification applies to testsieves manufactured with sieve cloth having a nominal a

4、per-ture size ranging from 125 millimeters (mm) down to 20micrometers (m).1.2 Additional reference information can be found in Speci-fications E 161, E 323, E 2016, and in Test Methods C 430 andE 2427.1.3 The values stated in SI units shall be consideredstandard for the dimensions of the sieve cloth

5、 openings and thewire diameters used in the sieve cloth. The values stated ininch-pound units shall be considered standard with regard tothe sieve frames, pans, and covers.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibilit

6、y of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C 430 Test Method for Fineness of Hydraulic Cement bythe 45-m (No. 325) SieveE 161 Specification for

7、 Precision Electroformed SievesE 323 Specification for Perforated-Plate Sieves for TestingPurposesE 1638 Terminology Relating to Sieves, Sieving Methodsand Screening MediaE 2016 Specification for Industrial Woven Wire ClothE 2427 Test Method for Acceptance by Performance Test-ing of U.S. Standard Te

8、st Sieves2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage32.4 ISO Standard:ISO 3310-1 Test SievesTechnical Requirements and Test-ing Part 1: Test Sieves of Metal Wire Cloth43. Terminology3.1 Definitions:3.

9、1.1 aperturethe dimension defining an opening in ascreening surface.3.1.2 crimpthe corrugation in the warp and shute wire, orboth. The crimp in the wires is formed either during theweaving process, or with a crimping machine prior to weaving.If formed during the weaving process, the tension existing

10、between the warp and shute wires fundamentally determinesthe respective amount or depth of crimp, which locks the wiresin place, and in part establishes the firmness of the sieve cloth.3.1.3 firmnessa subjective term referring to the planarrigidity of sieve cloth (as a roll good, not mounted in a te

11、stsieve frame), established by the tensile strength of the material,the relationship of the mesh to wire diameters, the type ofweave, and amount of crimp in the wires. The absence offirmness in sieve cloth is termed sleaziness.3.1.4 matched test sievea test sieve that reproduces theperformance resul

12、ts of another test sieve within user definedlimits for a designated material (for information only and maynot be in compliance with this Specification).3.1.5 meshthe number of wires or openings per linearinch (25.4 mm) counted from the center of any wire to a pointexactly 1 in. (25.4 mm) distant, in

13、cluding the fractionaldistance between either thereof.3.1.6 plain weavesieve cloth in which the warp wires andshute wires pass over one and under one in both directions.1This specification is under the jurisdiction ofASTM Committee E29 on Particleand Spray Characterization and is the direct responsi

14、bility of Subcommittee E29.01on Sieves, Sieving Methods, and Screening Media.Current edition approved May 1, 2009. Published June 2009. Originallyapproved in 1925. Last previous edition approved in 2004 as E 11 04.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM C

15、ustomer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.da

16、ps.mil.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.7 shute wiresthe wires running the short way of

17、, oracross the cloth as woven (also referred to as the shoot, fill, orweft wires).3.1.8 sievean apparatus for the purpose of sieving, con-sisting of a separating media mounted in a frame.3.1.9 sieve clothwoven wire cloth conforming to thisspecification.3.1.10 test sieve (wire cloth)a sieve manufactu

18、red bymounting sieve cloth in a frame, designed for use in particlesize analysis by sieving.3.1.11 compliance test sievea test sieve manufacturedusing sieve cloth which has been inspected prior to beingmounted in the sieve frame; and that meets the requirements ofTable 1 in part based on the standar

19、d deviation of the requirednumber of sample openings per 100 square feet of sieve cloth(column 7) not exceeding the maximum allowable for aconfidence level of 66% (column 8).3.1.12 inspection test sievea test sieve manufactured us-ing sieve cloth which has been inspected after being mountedin the si

20、eve frame; and that meets the requirements of Table 1in part based on the standard deviation of the required numberof sample openings in the test sieve (column 9) not exceedingthe maximum allowable for a confidence level of 99% (column10).3.1.13 calibration test sievea test sieve manufacturedusing s

21、ieve cloth which has been inspected after being mountedin the sieve frame; and that meets the requirements of Table 1in part based on the standard deviation of the required numberof sample openings in the test sieve (column 11) not exceedingthe maximum allowable for a confidence level of 99.73%(colu

22、mn 12).3.1.14 twill weavesieve cloth in which the warp wires andshute wires pass over two and under two wires in bothdirections.3.1.15 warp wiresthe wires running the long way of thecloth as woven.3.2 Additional terms can be found in Terminology E 1638.4. Ordering Information4.1 Orders for items und

23、er this specification should includethe following information as required:4.1.1 Description of item(s) (Test Sieve or Sieve Cloth),4.1.2 ASTM E 11 designation and year of issue,4.1.3 Quantity of each item, and4.1.4 Sieve designation (Table 1, Standard Column 1, Al-ternate Column 2).4.2 Test sieves i

24、n standard circular frame:4.2.1 Nominal sieve frame diameter (see Table 2), and4.2.2 Nominal sieve frame height (see Table 2).4.3 For sieve cloth not in frames or in nonstandard frames:4.3.1 Sieve cloth designation, and4.3.2 Description of nonstandard frame.4.4 For U.S. Government purchases, if supp

25、lementary re-quirements apply:4.4.1 Compatible sieve pans and covers, and4.4.2 Special requirements (specific type of metal for sievecloth and frames, test sieve designation and or matched sievesfor example).5. Sieve Cloth Requirements5.1 The sieve cloth used in test sieves shall meet therequirement

26、s of Table 1 and shall be designated SpecificationE 11 Sieve Cloth. The number of inspected apertures shall bein accordance with Table 1 (Column 7). Sieve cloth conform-ing to this specification shall be woven from stainless steel,brass, or bronze. Sieve cloth with openings greater than orequal to 7

27、5 micrometers shall be woven using a plain weave.For sieve cloth with openings equal to or less than 63micrometers the sieve cloth may be supplied using a twillweave. The sieve cloth shall not be coated or plated.5.2 All measurements of openings and wire diameters shallbe made along the midpoints of

28、 the openings as shown in Fig.1.5.3 There shall be no punctures or obvious defects in thesieve cloth.5.4 Test sieves can be supplied based on different levels ofconfidence as Compliance Sieves, Inspection Sieves, andCalibration Sieves. Calibration sieves have had at least twice asmany openings measu

29、red as Inspection sieves.5.5 Each test sieve must be examined and found to be freeof manufacturing defects.6. Technical Requirements6.1 Opening Sizes, Tolerances, and Standard Deviation:6.1.1 Four tolerances shall be applied: the variation foraverage opening (Y), the maximum variation (X), the maxim

30、umstandard deviation and the wire diameter. The opening toler-ances apply to the opening sizes, measured on the midpoint ofthe opening (see Fig. 1), and applied separately in both thewarp and shute directions.6.1.2 The average opening size shall not exceed the sievedesignation by more than 6Y (Table

31、 1, Column 4):Y 5w0.98271 1.6 (1)where Y and w are expressed in micrometers.6.1.3 The maximum opening size measured shall not exceedthe nominal opening size w (Table 1, Column 1), by more thanX (Table 1, Column 5):X 52w0.75!31 4w0.25(2)where X and w are expressed in micrometers.6.1.4 The intermediat

32、e value Z shall be stated as follows:Z 5 X 1 Y! / 2 (3)6.1.5 The maximum standard deviation is calculated basedon the Gaussian normal distribution curve, where the areaunder the curve to the maximum value X minus the area underthe curve to the intermediate value Z, is equal to this criticalarea betw

33、een (w + Z) and (w + X) not exceeding more than 5 %of the openings (see Appendix X2). The resulting tolerancesfor sigma are given in Table 1 for Compliance sieve cloth(Column 8).6.1.5.1 In order to increase the probability or acceptanceconfidence level from 66 % at one-sigma to Xs, specifically99 %

34、(2.58s) and 99.73 % (3s) for Inspection and Calibrationsieves respectively, these maximum standard deviation valuesE11092TABLE 1 Nominal Dimensions and Permissible Variations for Sieve Cloth and Compliance, Inspection and Calibration Test Sieves(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13)

35、 (14) (15)Sieve DesignationNominalSieveOpening(in.)6YVariationfor AverageOpening+XMaximumVariationfor OpeningResultingMaximumIndividualOpeningCompliance Sieves Inspection Sieves Calibration SievesTypicalWireDiameterPermissible Rangeof ChoiceStandard AlternativeSampleOpeningsper 100 ft2MaximumStandar

36、dDeviationSampleOpeningsper SieveMaximumStandardDeviationSampleOpeningsper SieveMaximumStandardDeviationMin Maxmillimeter inches millimeter millimeter millimeter millimeter125 5 in. 5 3.66 4.51 129.51 20 all all 8 6.8 9.2106 4.24 in. 4.24 3.12 3.99 109.99 20 all all 6.3 5.4 7.2100 4 in. 4 2.94 3.82

37、103.82 20 all all 6.3 5.4 7.290 312 in. 3.5 2.65 3.53 93.53 20 all all 6.3 5.4 7.275 3 in. 3 2.22 3.09 78.09 20 all all 6.3 5.4 7.263 212 in. 2.5 1.87 2.71 65.71 20 all all 5.6 4.8 6.453 2.12 in. 2.12 1.58 2.39 55.39 20 all . all 5 4.3 5.850 2 in. 2 1.49 2.29 52.29 20 all all 5 4.3 5.845 134 in. 1.7

38、5 1.35 2.12 47.12 20 . all all 4.5 3.8 5.237.5 112 in. 1.5 1.13 1.85 39.35 20 1.374 all all 4.5 3.8 5.231.5 114 in. 1.25 0.95 1.63 33.13 20 1.066 all all 4 3.4 4.626.5 1.06 in. 1.06 0.802 1.44 27.94 20 0.869 15 0.584 all 3.55 3 4.125 1.00 in. 1 0.758 1.38 26.38 20 0.823 15 0.553 all 3.55 3 4.122.478

39、 in. 0.875 0.681 1.27 23.67 150 0.734 15 0.493 all 3.55 3 4.11934 in. 0.750 0.579 1.13 20.13 150 0.622 15 0.418 30 0.446 3.15 2.7 3.51658 in. 0.625 0.490 0.99 16.99 150 0.527 15 0.354 30 0.378 3.15 2.7 3.613.2 0.530 in. 0.530 0.406 0.86 14.06 150 0 441 15 0.296 30 0.316 2.8 2.4 3.212.512 in. 0.500 0

40、.385 0.83 13.33 150 0.421 15 0.283 30 0.302 2.5 2.1 2.911.2716 in. 0.438 0.346 0.77 11.97 150 0.382 15 0.256 30 0.274 2.5 2.1 2.99.538 in. 0.375 0.295 0.68 10.18 150 0.330 15 0.222 30 0.237 2.24 1.9 2.68516 in. 0.312 0.249 0.60 8.60 150 0.284 15 0.191 30 0.204 2 1.7 2.36.7 0.265 in. 0.265 0.210 0.53

41、 7.23 150 0.245 15 0.164 30 0.175 1.8 1.5 2.16.314 in. 0.250 0.197 0.51 6.81 150 0.233 15 0.157 30 0.167 1.8 1.5 2.15.6 No. 312 0.223 0.176 0.47 6.07 150 0.211 15 0.142 30 0.151 1.6 1.3 1.94.75 No. 4 0.187 0.150 0.41 5.16 150 0.182 15 0.123 30 0.131 1.6 1.3 1.94 No. 5 0.157 0.127 0.37 4.37 150 0.161

42、 15 0.108 30 0.115 1.4 1.2 1.73.35 No. 6 0.132 0.107 0.32 3.67 200 0.138 20 0.097 40 0.103 1.25 1.06 1.52.8 No. 7 0.110 0.090 0.29 3.09 200 0.121 20 0.085 40 0.090 1.12 0.95 1.32.36 No. 8 0.0937 0.076 0.25 2.61 200 0.104 20 0.073 40 0.077 1 0.85 1.152 No. 10 0.0787 0.065 0.23 2.23 250 0.094 25 0.068

43、 50 0.072 0.9 0.77 1.041.7 No. 12 0.0661 0.056 0.20 1.90 250 0.081 25 0.059 50 0.062 0.8 0.68 0.921.4 No. 14 0.0555 0.046 0.18 1.58 400 0.071 40 0.055 80 0.057 0.71 0.6 0.821.18 No. 16 0.0469 0.040 0.16 1.34 400 0.063 40 0.049 80 0.051 0.63 0.54 0.721 No. 18 0.0394 0.034 0.14 1.14 400 0.055 40 0.042

44、 80 0.044 0.56 0.48 0.64micrometer inches micrometer micrometer micrometer micrometer850 No. 20 0.0331 29.1 127 977 400 48.76 40 37.73 80 39.36 0.5 0.43 0.58710 No. 25 0.0278 24.7 112 822 500 42.63 50 33.82 100 35.14 0.45 0.38 0.52600 No. 30 0.0234 21.2 101 701 500 38.00 50 30.14 100 31.32 0.4 0.34

45、0.46500 No. 35 0.0197 18.0 89 589 600 33.23 60 26.85 120 27.82 0.315 0.27 0.36425 No. 40 0.0165 15.5 81 506 600 29.95 60 24.20 120 25.08 0.28 0.24 0.32355 No. 45 0.0139 13.3 72 427 800 26.45 80 21.95 160 22.64 0.224 0.19 0.26300 No. 50 0.0117 11.5 65 365 800 23.70 80 19.66 160 20.29 0.2 0.17 0.23250

46、 No. 60 0.0098 9.9 58 308 800 21.02 80 17.44 160 17.99 0.16 0.13 0.19212 No. 70 0.0083 8.7 52 264 800 18.79 80 15.59 160 16.08 0.14 0.12 0.17180 No. 80 0.0070 7.6 47 227 1000 16.85 100 14.24 200 14.65 0.125 0.106 0.15150 No. 100 0.0059 6.6 43 193 1000 15.30 100 12.93 200 13.30 0.1 0.085 0.115125 No.

47、 120 0.0049 5.8 38 163 1000 13.51 100 11.41 200 11.74 0.09 0.077 0.104106 No. 140 0.0041 5.2 35 141 1000 12.39 100 10.47 200 10.77 0.071 0.06 0.08290 No. 170 0.0035 4.6 32 122 1000 11.27 100 9.53 200 9.80 0.063 0.054 0.07275 No. 200 0.0029 4.1 29 104 1000 10.23 100 8.64 250 9.02 0.05 0.043 0.05863 N

48、o. 230 0.0025 3.7 26 89 1000 9.18 100 7.76 250 8.09 0.045 0.038 0.05253 No. 270 0.0021 3.4 24 77 1000 8.44 100 7.13 250 7.44 0.036 0.031 0.04145 No. 325 0.0017 3.1 22 67 1000 7.76 100 6.56 250 6.84 0.032 0.027 0.03738 No. 400 0.0015 2.9 20 58 1000 7.09 100 5.99 300 6.31 0.03 0.024 0.03532 No. 450 0.

49、0012 2.7 18 50 1000 6.42 100 5.42 300 5.71 0.028 0.023 0.03325 No. 500 0.0010 2.5 16 41 1000 5.71 100 4.82 300 5.06 0.025 0.021 0.02920 No. 635 0.0008 2.3 15 35 1000 5.33 100 4.51 300 4.75 0.02 0.017 0.023Column 3These numbers are only approximate but are in use for reference; the sieve shall be identified by the standard designation in millimeters or micrometers.Columns 9 and 11See Annex A1, which specifies that all openings will be inspected for test sieves having 15 openings or