ASTM D7541-2011 3750 Standard Practice for Estimating Critical Surface Tensions《临界表面张力估算规程》.pdf
《ASTM D7541-2011 3750 Standard Practice for Estimating Critical Surface Tensions《临界表面张力估算规程》.pdf》由会员分享,可在线阅读,更多相关《ASTM D7541-2011 3750 Standard Practice for Estimating Critical Surface Tensions《临界表面张力估算规程》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D7541 11Standard Practice forEstimating Critical Surface Tensions1This standard is issued under the fixed designation D7541; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parent
2、heses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers procedures for estimating values ofthe critical surface tension of surfaces by observing the wettingand dewetting of a series of l
3、iquids (usually organic solvents)applied to the surface in question.1.2 Another technique, measurement of the contact angles,u, of a series of test liquids and plotting cos u versus surfacetension (Zisman plots), provides data that allow the determi-nation of more exact values for critical surface t
4、ension.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establi
5、sh appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D2578 Test Method for Wetting Tension of Polyethyleneand Polypropylene Films2.2 Nordtest Standards:3NT poly 176 Spreading Surface Tension by
6、the AppliedDroplet Method.3. Terminology3.1 Definitions:3.1.1 critical surface tension, nthe surface tension of ahypothetical liquid that would just spontaneously spread ifapplied as a drop to the surface in question; any liquid with asurface tension lower than the critical surface tension willsprea
7、d spontaneously.4. Summary of Practice4.1 In this practice, a series of liquids of gradually increas-ing surface tension are applied to a surface in the form ofdrops, narrow strips, or spots. Drops may be applied using adropper, syringe or other device capable of producing indi-vidual drops. Liquid
8、strips or spots are applied to the surface byswabbing with saturated cotton swabs or by another type ofapplicator, such as one that is similar to a marker pen. In thecase of the drop, the observer determines whether the dropstays in place or spreads. In the case of the liquid strip or spot,the quest
9、ion is whether the liquid stays in place or dewets andcrawls. In each case, the break point between wetting anddewetting provides the critical surface tension.5. Significance and Use5.1 Knowledge of the critical surface tension of substrates,primers and other coatings is useful for explaining or pre
10、dict-ing wettability by paints and other coatings applied to thosesurrfaces. Surfaces with low critical surface tensions usuallyare prone to suffer defects such as crawling, picture framing,cratering and loss of adhesion when painted. Low or irregularvalues, or both, often are indicative of contamin
11、ation that couldreduce adhesion. Surfaces with high critical surface tensionsare easy to wet and usually provide an excellent platform forpainting.5.2 The swab, marking pen and draw-down tests all simu-late the application of a film5.3 The swab and marking pen techniques are simple andrapid and are
12、particularly useful for testing in the field or oncurved, irregular or porous surfaces where contact anglescannot be measured. The drop test does not work well on suchsurfaces and the draw-down method requires a flat specimenthat is relatively large.5.4 The estimation of critical surface tension has
13、 beenuseful in characterizing surfaces before and after cleaningprocesses such as power washes and solvent wipes in order toevaluate the efficiency of the cleaning.5.5 One or more of these techniques could be the basis of ago/no-go quality control test where if a certain liquid wets, thesurface is a
14、cceptable for painting, but if that liquid retracts andcrawls, the surface is not acceptable.5.6 Another go/no go test is possible where the test liquid isa paint and the surface is a substrate, primer or basecoat. Aform of this test has been used for coatings for plastics.1This practice is under th
15、e jurisdiction of ASTM Committee D01 on Paint andRelated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.23 on Physical Properties of Applied Paint Films.Current edition approved Feb. 1, 2011. Published February 2011. Originallyapproved in 2009. Last previou
16、s edition approved in 2009 as D7541 - 09. DOI:10.1520/D7541-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM websit
17、e.3For Nordtest standards, see or contactNordtest, Tekniikantie 12, FIN-02150 Espoo, Finland.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6. Interferences6.1 The specimen must be clean in order for results to bemeaningful. The su
18、rface must not be touched or rubbed.6.2 The surface tensions of test liquids, especially those thatare mixtures, are subject to change with time. Test liquidsurface tensions should be confirmed before they are first used,measured periodically after that and whenever change issuspected.6.3 Test liqui
19、ds may become contaminated, in which caseresults with them will be meaningless. Test liquid surfacetensions should be confirmed before they are first used,measured periodically after that and whenever contamination issuspected.6.4 High ambient temperature may cause rapid evaporationof test liquids a
20、nd make it difficult to determine whetherretraction has occurred or shrinkage is due to evaporation.7. Apparatus7.1 Several of one of the following types of applicators:7.1.1 Cotton swab (small ball of cotton at the end of a stick).7.1.2 Marker pen type applicator.7.1.3 Dropper or syringe.7.1.4 Othe
21、r device with the ability to apply a drop, strip, orspot.7.2 Drawdown Baronly for draw-down test.7.3 Instrument or devices for measuring temperature andhumidity.8. Materials8.1 Swab, drop and draw-down tests.8.1.1 Test liquids.8.1.1.1 The original publication on the swab test4specifiedthe liquids in
22、 Table 1 (listed along with their surface tensions).This set of liquids has a large surface tension gap between 24and 35 dynes/cm.8.1.1.2 Test Method D2578 specifies mixtures of formamideand ethylene glycol monomethyl ether (both reagent grade).Mixtures can be designed so as to produce any combinati
23、on ofsurface tension values.8.1.1.3 The drop test publications5,6specify mixtures ofethanol and water, but do not give details of the proportions.8.1.1.4 Nordtest Method NT poly 1763includes a table ofsurface tensions for ethanol/water mixtures at 23C, whichgives values ranging from 22 to 72 mN/m in
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD754120113750STANDARDPRACTICEFORESTIMATINGCRITICALSURFACETENSIONS 临界 表面张力 估算 规程 PDF

链接地址:http://www.mydoc123.com/p-525754.html