ASTM D6754-2002 Standard Specification for Ketone Ethylene Ester Based Sheet Roofing《酮乙烯酯基薄板屋面材料标准规范》.pdf

《ASTM D6754-2002 Standard Specification for Ketone Ethylene Ester Based Sheet Roofing《酮乙烯酯基薄板屋面材料标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6754-2002 Standard Specification for Ketone Ethylene Ester Based Sheet Roofing《酮乙烯酯基薄板屋面材料标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 6754 02Standard Specification forKetone Ethylene Ester Based Sheet Roofing1This standard is issued under the fixed designation D 6754; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numb

2、er in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers flexible sheet made fromketone ethylene ester (KEE) as the primary polymer intendedfor use in single ply roofing

3、 membrane exposed to the weather.The sheet shall be reinforced with fabric.1.2 In-place roof system design criteria, such as fire resis-tance, field-seaming strength, material compatibility, upliftresistance, in-situ shrinkage, among others, are factors thatmust be considered, but are beyond the sco

4、pe of this specifi-cation.1.3 The following precautionary caveat pertains to the testmethods portion only, Section 8, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to es

5、tablish appropriate safety and healthpractices and determine the applicability of regulatory require-ments prior to use.2. Referenced Documents2.1 ASTM Standards:D 471 Test Method for Rubber PropertyEffect of Liq-uids2D 751 Test Methods for Coated Fabrics3D 1079 Terminology Relating to Roofing, Wate

6、rproofing,and Bituminous Materials4D 1204 Test Method for Linear Dimensional Changes ofNonrigid Thermoplastic Sheeting or Film at ElevatedTemperature4D 2136 Test Method for Coated FabricsLow-Temperature Bend Test2D 3045 Practice for Heat Aging of Plastics Without Load5D 3389 Test Method for Coated F

7、abrics Abrasion Resis-tance (Rotary Platform, Double-head Abrader)3D 5602 Test Method for Static Puncture Resistance ofRoofing Membrane Specimens6D 5635 Test Method for Dynamic Puncture Resistance ofRoofing Membrane Specimens6G 21 Practice for Determining Resistance of SyntheticPolymeric Materials t

8、o Fungi7G 151 Practice for Exposing Nonmetallic Materials in Ac-celerated Test Devices that Use Laboratory Light Sources7G 154 Practice for Operating Florescent Light Apparatusfor UV Exposure of Nonmetallic Materials7G 155 Practice for Operating Xenon Arc Light Apparatusfor Exposure of Non-Metallic

9、Materials73. Terminology3.1 DefinitionsTerminology D 1079 shall apply to thisspecification.3.2 ketone ethylene ester (KEE), na high molecularweight thermoplastic copolymer of ethylene, containing carbonmonoxide and either vinyl acetate or acrylate monomer whichare incorporated to provide softness an

10、d polarity.83.3 polymer content, nin this specification, polymer con-tent shall be defined as polymeric materials which are in thesolid state at room temperature, and are high (greater than50 000 Mw) in molecular weight. Other ingredients, known tothe art of polymer compounding, such as certain waxe

11、s,stabilizers, and other additives, while polymeric in nature arenot considered to be part of the base polymer system.4. Materials and Manufacture4.1 The sheet shall be formulated from the appropriatepolymers and other compounding ingredients. The KEE poly-mer shall be a minimum of 50 % by weight of

12、 the polymercontent of the sheet.4.2 The sheet shall be reinforced internally with a fabric.4.3 To make seam and repairs, the sheet shall be capable ofbeing bonded watertight to itself during the design service lifeof the sheets. The manufacturer shall recommend a suitablemethod. Design service life

13、 is defined as the designated timeperiod of intended system performance.5. Physical Properties5.1 The sheet shall conform to the physical requirements1This specification is under the jurisdiction of ASTM Committee D08 onRoofing, Waterproofing, and Bituminous Materials and is the direct responsibilit

14、y ofSubcommittee D08.18 on Nonbituminous Organic Roof Coverings.Current edition approved Jan. 10, 2002. Published March 2002.2Annual Book of ASTM Standards, Vol 09.01.3Annual Book of ASTM Standards, Vol 09.02.4Annual Book of ASTM Standards, Vol 08.01.5Annual Book of ASTM Standards, Vol 08.02.6Annual

15、 Book of ASTM Standards, Vol 04.04.7Annual Book of ASTM Standards, Vol 14.04.8Ester groups of the vinyl acetate or acrylate are pendant from the ethylenebackbone and reduce crystallinity, which provides flexibility. Carbon monoxidegroups within the polymer backbone provide polarity. The KEE polymer

16、is thereforea flexible polymer, which is miscible with other polymers of similar polarity.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.prescribed in Table 1.5.2 Individual specimens must meet or exceed table values.6. Dimensions a

17、nd Permissible Variations6.1 The width and length of the sheet shall be agreed uponbetween the purchaser and the supplier as part of the purchasecontract. The width and length tolerance shall be +3 % -0 %after permitting the sheet to relax1hat236 1C (73 6 2F).6.2 The thickness and thickness toleranc

18、e shall be agreedupon between the purchaser and supplier as part of thepurchase contract, subject to the minimum requirement inTable 1.7. Workmanship, Finish, and Appearance7.1 The sheet, including factory seams if present, shall bewatertight and be visually free of pinholes, particles of foreignmat

19、ter, undispersed raw materials, protruding reinforcement,and other manufacturing defects that might affect serviceabil-ity.7.2 The sheet shall be visually free of nicks and cuts, voids,thin areas, delaminations, moisture-bound fabric, or otherdefects.7.3 Edges of the sheet shall be straight and flat

20、 so that theymay be seamed to one another.8. Test Methods8.1 Thickness, OverallTest Method D 751.8.2 Thickness, Coating Over Reinforcement OpticalMethodsee Annex A1, Optical Method for Measurement ofThickness of Coating.8.3 Breaking StrengthTest Method D 751, Procedure BStrip Method.8.4 Elongation a

21、t BreakTest Method D 751.8.5 Tearing StrengthTest Method D 751, Procedure BTongue Tear Method, 200-mm (8-in.) by 250-mm (10-in.)specimen size. Test at 5.0 mm/s (12 in./min).8.6 Linear Dimensional ChangeTest Method D 1204, 1 hat 100 6 2C (212 6 5F).8.7 Fabric AdhesionTest Method D 751, 5.0-mm/s (12-i

22、n./min) jaw speed.8.8 Heat AgingPractice D 3045, at 80 6 2C (176 6 4F)for 56 days 6 2h.8.8.1 After Heat Aging Low Temperature BendTestMethod D 2136, at -35 6 1C (-30 6 2F).8.9 Low Temperature BendTest Method D 2136 at -35 61C (-30 6 2F).8.10 Water AbsorptionTest Method D 471, Procedure forexposure t

23、o one side only in water, at 70 6 2C (158 6 4F)for 166 h.8.11 Factory Seam StrengthTest Method D 751, GrabMethod.8.12 Hydrostatic ResistanceTest Method D 751, MethodA, Procedure 1.8.13 Static Puncture TestTest Method D 5602, at a load of45 kg (99 lbf) min. at 23 6 1C (73 6 2F).8.14 Dynamic Puncture

24、TestTest Method D 5635, at en-ergy of 10 J min. 23 6 1C (73 6 2F).8.15 Accelerated Weathering TestPractice G 155, 5000 hxenon arc light exposure. Practice using daylight filter 0.35W/m2at 340 nm; deionized water; 102-min light exposure,18-min light and spray; black panel temperature (63 6 2C)relativ

25、e humidity (50 6 5 %).8.16 Accelerated Weathering TestPractice G 154, 5000 hfluorescent lamp UVA-340, cycle 8-h light at 70 6 3C (158 65.5F), 4-h condensation at 50 6 3C (122 6 5.5F).8.17 Fungi ResistancePractice G 21, 28 days.8.18 Abrasion TestTest Method D 3389, using the H-18Wheel and 1000-g load

26、. Run until fabric is visible.8.19 DimensionsTest Method D 751, after unrolling orunfolding and permitting the sheet to relax for1hat236 lC(73 6 2F).9. Inspection and Special Testing9.1 The manufacturer shall inspect and test the product toassure compliance of the product with this standard.9.2 The

27、purchaser may, in the contract, order special tests,which the supplier shall be required to make beyond thosedescribed in Table 1.9.3 If the results of any tests do not conform to therequirements of this specification, retesting to determine con-formity shall be performed as agreed upon between thep

28、urchaser and supplier.10. Rejection and Resubmittal10.1 Failure to conform to any one of the requirementsprescribed in this specification shall constitute grounds forrejection. The seller shall have the right to reinspect therejected shipment and resubmit the lot after removal of thosepackages not c

29、onforming to the specified requirements.11. Product Marking11.1 The sheet shall be identified on the side intended to beTABLE 1 Physical Requirements of the KEE-ReinforcedMembranePropertyThickness, min., mm (in.) 0.79 (0.031)Thickness over fiber, min., mm (in.) 0.15 (0.006)Breaking strength, strip ,

30、 N (lbf) 1175 (265)Elongation at break, strip, min., % 15Tearing strength, min., N (lbf) 335 (75)Lineal dimension change, max., % 1.3Fabric adhesion, min., N/m (lbf/in.) 225 (13)Retention of properties after heat aging:Breaking strength, strip, min., % of original 90Elongation at break, strip, min.,

31、 % of original 90Low-temperature bend after heat aging passLow-temperature bend passChange in weight after exposure in water, max, % 0.0, +6.0Factory seam strength, min., N (lbf) 1780 (400)Hydrostatic resistance, min., MPa (psi) 3.5 (500)Static puncture resistance passDynamic puncture resistance pas

32、sAccelerated weathering test after 5000-h xenon arc light exposureCracking (73 magnification) noneCrazing (73 magnification) noneAccelerated weathering test after 5000-h fluorescent light exposureCracking (73 magnification) noneCrazing (73 magnification) noneFungi resistanceSustained growth no growt

33、hDiscoloration noneAbrasion test, min., cycles 1500D 67542exposed to the weather with this ASTM designation, the nameof the manufacturer or supplier, and KEE. The type ofidentification is at the manufacturers option. Such identifica-tion shall occur at intervals not to exceed3m(9ft10in.) in thelong

34、direction. The identification shall be applied in such amanner as to be legible five years from installation. Identifi-cation shall not be required when so specified by the purchaser.12. Packaging and Package Marking12.1 The material shall be rolled on a substantial core andpackaged in a standard co

35、mmercial manner unless otherwisespecified in the contract or order.12.2 Shipping container shall be marked with the name ofthe material, the stock and lot numbers, and the ASTMdesignation number, the size and quantity, the name of themanufacturer or the supplier, and the number of the contract orord

36、er.13. Keywords13.1 flexible sheet; KEE; reinforcing fabrics; reinforcingfibers; roofing; seams; single-ply roofing membraneANNEX(Mandatory Information)A1. OPTICAL METHOD FOR MEASUREMENT OF THICKNESS OF COATINGA1.1 ScopeA1.1.1 This is a method for measuring the thickness of thecoating over fiber bac

37、king or reinforcing fabric.A1.2 Measurement MethodA1.2.1 PrincipleThe thickness of coating material overfiber, fabric, or scrim can be observed with a standardreflectance microscope. Measurement is made with a calibratedeyepiece.A1.2.2 Apparatus:A1.2.2.1 Microscope,603 with reticle.A1.2.2.2 Light So

38、urceIf light source on the microscope isnot adequate, a small high-intensity lamp may also be used.A1.2.2.3 Stage Micrometer, 0.0254-mm (0.001-in.) divi-sions.A1.2.3 Calibration Procedure:A1.2.3.1 Place a standard reflectance stage micrometer inplace of the specimen.A1.2.3.2 Turn on microscope light

39、 source.A1.2.3.3 Position the reticle eyepiece and the micrometersuch that the scales are superimposed. Focus the specimen andreticle by turning the vertical adjustment knob.A1.2.3.4 Locate a point at which both scales line up. Countthe number of micrometer divisions away. Measure to thenearest 0.01

40、25 mm (0.0005 in. or 0.5 mil). Increasing thenumber of divisions measured may optimize the calibration.A1.2.3.5 Repeat the calibration three times and average theresults. A calibration example is given below:If four reticle divisions (RD) are found equal to 4.5 mi-crometer divisions (MD), then:1 (RD

41、) 4.5/4 (MD) or (RD) = 1.125(MD)Since 1 micrometer division is also equal to 25.4 m (0.001in. or 1.0 mil), therefore:1 (RD) = 28.6 m (0.001 125 in. or 1.125 mils) or the calibration fac-torA1.2.4 Specimen Analysis:A1.2.4.1 Carefully center a sharp single edge razor orequivalent over the fiber inters

42、ections along the x-x axis.A1.2.4.2 Make a clean bias cut completely through thesheet.A1.2.4.3 Remove the razor-cut section and mount in com-mon putty with the cut surface facing upward.A1.2.4.4 Observe the cut surface with the eyepiece reticle.Measure the thickness of the coating on either side of

43、thethread intersection by counting the number of reticle divisions(to the nearest one-half division).A1.2.4.5 Sample three areas of the coatings and average theresults.A1.3 Calculation and ReportA1.3.1 Multiply the number of reticle divisions representingthe thickness of the coating by the calibrati

44、on factor. Report theaverage results from three areas of the coating to the nearest12.7 m (0.0005 in. or 0.5 mils).A1.4 Precision and BiasA1.4.1 PrecisionMeasurements are accurate to 6 12.7m (0.005 in. or 0.5 mils) when the thickness is about 0.5 mm(0.020 in. or 20 mils).A1.4.2 BiasSince there is no

45、 accepted reference materialsuitable for determining the bias for measuring coating thick-ness, no statement on bias is being made.D 67543ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this st

46、andard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years a

47、ndif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee,

48、 which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 67544