ASTM D6542-2005(2010) 7500 Standard Practice for Tonnage Calculation of Coal in a Stockpile《计算堆料中煤吨数计算的标准操作规程》.pdf

《ASTM D6542-2005(2010) 7500 Standard Practice for Tonnage Calculation of Coal in a Stockpile《计算堆料中煤吨数计算的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6542-2005(2010) 7500 Standard Practice for Tonnage Calculation of Coal in a Stockpile《计算堆料中煤吨数计算的标准操作规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6542 05 (Reapproved 2010)Standard Practice forTonnage Calculation of Coal in a Stockpile1This standard is issued under the fixed designation D6542; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revi

2、sion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice is used to calculate the mass (commonlyexpressed in tons) of coal in a storage pile using the volume ofthe stockp

3、ile by Test Method D6172 and the density of the coaldetermined by Test Method D6347/D6347M.1.2 This practice is applicable to all ranks of coal.1.3 The user of this standard determines when the densityvalues provided by the survey require an adjustment formoisture.1.4 The values stated in either inc

4、h-pounds or SI units are tobe regarded separately as standard. Within the text, the SI unitsare shown in brackets. The values stated in each system are notexact equivalents; therefore, each system must be used inde-pendently of the other. Combining values from the two systemscan result in nonconform

5、ance with the specification.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations

6、prior to use.2. Referenced Documents2.1 ASTM Standards:2D121 Terminology of Coal and CokeD2013 Practice for Preparing Coal Samples for AnalysisD3173 Test Method for Moisture in the Analysis Sample ofCoal and CokeD3302 Test Method for Total Moisture in CoalD6172 Test Method for Determining the Volume

7、 of BulkMaterials Using Contours or Cross Sections Created byDirect Operator Compilation Using Photogrammetric Pro-ceduresD6347/D6347M Test Method for Determination of BulkDensity of Coal Using Nuclear Backscatter Depth DensityMethods3. Terminology3.1 DefinitionsThere are no terms in this practice t

8、hatrequire new or other than dictionary definitions. Many terms inthis Practice may be found in Terminology D121.4. Significance and Use4.1 The physical inventory of tons of coal in a stockpile, ascalculated by this practice, may be used for accounting and taxpurposes.4.2 The inventory results may b

9、e compared to other esti-mates of the inventory, such as:4.2.1 Tons from a previous inventory less tons shipped orconsumed.4.2.2 Tons estimated to have been received (from conveyor,rail or truck weights) less tons shipped or consumed.5. Procedure5.1 Determine if the reported tonnage should be on ana

10、s-determined basis, or some other moisture adjusted basis. Ifthe moisture content was determined on the density-measurement samples (see Test Method D6347/D6347M), thenthe density data (and the tonnage) can be calculated to a drybasis or to another moisture-containing basis.5.1.1 Use Eq 1 or Eq 2 to

11、 adjust the as-determined densityto a different moisture basis. The percent moisture determinedin accordance with Test Methods D3173, D3302,orD2013 inthe samples collected according Test Method D6347/D6347Mis used in Eq 1 or Eq 2.5.1.2 Use Eq 1 to adjust the average density values to a drybasis:Ddry

12、5 Ddet3S1 2Mdet100D(1)where:Ddry= density in lb/ft3(kg/m3) on a dry basis,Ddet= density in lb/ft3(kg/m3) on an as-determined mois-ture basis, andMdet= % moisture, as determined on the density sample.1This practice is under the jurisdiction of ASTM Committee D05 on Coal andCoke and is the direct resp

13、onsibility of Subcommittee D05.07 on PhysicalCharacteristics of Coal.Current edition approved Sept. 1, 2010. Published January 2011. Originallyapproved in 2000. Last previous edition approved in 2005 as D654205 DOI:10.1520/D6542-05R10.2For referenced ASTM standards, visit the ASTM website, www.astm.

14、org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.3 Use E

15、q 2 to adjust the as-determined density values tosome other moisture basis such as as-received, as-shipped,as-stockpiled, etc.Dadj5 Ddet3S100 2 Madj100 2 MdetD(2)where:Dadj= density in lb/ft3(kg/m3) on a desired moisture basis,Ddet= density in lb/ft3(kg/m3) on an as-determined mois-ture basis, andMa

16、dj= % moisture, at the desired moisture basis, andMdet= % moisture, as determined on the density sample.5.2 Calculate the tons of coal in the stockpile using Eq 3:T 5D *Vt(3)where:T = total stockpile tons,D = mean of density samples in lb/ft3kg/m3 (from TestMethod D6347/D6347M),V = total volume of s

17、tockpile in ft3m3 (from Test MethodD6172), andt = 2000 lb/t (short ton) 1000 kg/Mg (metric tonne).6. Confidence Interval Calculation6.1 A measurement is stated as a quantity, plus or minussome confidence interval, at some level of significance. In thecase of volume, this translates to total volume (

18、in ft3), plus orminus some tolerance factor (stated as percent of total volume),calculated at a significance level consistent with Annex A5 ofTest Method D6347/D6347M, D6172.6.2 The tolerance for the inventory results combines thetolerances, in %, of the density survey data and the volumetricdata ac

19、cording to Eq 4:C 5 =D21 A2(4)where:C = combined tolerances of density and volume in %,D = tolerance of density test in percent (from Test MethodD6347/D6347M), andA = tolerance of volumetric survey in percent (from TestMethod D6172).7. Report7.1 The minimum information to be reported is as follows:7

20、.1.1 The owner(s) and location of the stockpile.7.1.2 The dates when the density and the volume weredetermined.7.1.3 Tons of coal in the stockpile as calculated by Eq 3.7.1.4 The density and volume values used in the calcula-tions.7.1.5 The moisture defining the basis on which the densitywas calcula

21、ted.7.1.6 The confidence interval in percent.8. Precision and Bias8.1 PrecisionThe precision of the result is given by Eq 4.8.2 BiasSince there is no acceptable reference method fordetermining the bias for the procedure for tonnage, bias has notbeen determined.9. Keywords9.1 density; stockpile; tonn

22、age; tons; volumeASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of

23、 such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for a

24、dditional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to

25、 the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D6542 05 (2010)2