ASTM D5960-2003 Standard Specification for Technical Grade Ethylene Dichloride《工业品位的二氯化乙烯的标准规范》.pdf

《ASTM D5960-2003 Standard Specification for Technical Grade Ethylene Dichloride《工业品位的二氯化乙烯的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5960-2003 Standard Specification for Technical Grade Ethylene Dichloride《工业品位的二氯化乙烯的标准规范》.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 5960 03Standard Specification forTechnical Grade Ethylene Dichloride1This standard is issued under the fixed designation D 5960; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

2、parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers technical grade ethylenedichloride.2.

3、 Referenced Documents2.1 ASTM Standards:D 2108 Test Method for Color of Halogenated OrganicSolvents and Their Admixtures (Platinum-Cobalt Scale)2D 2111 Test Methods for Specific Gravity of HalogenatedOrganic Solvents and Their Admixtures2D 2989 Test Method for Acidity-Alkalinity of HalogenatedOrgani

4、c Solvents and Their Admixtures2D 3401 Test Methods for Water in Halogenated OrganicSolvents and Their Admixtures2D 6806 Practice for Analysis of Halogenated Solvents andTheir Admixtures by Gas Chromatography22.2 U. S. Government Documents:49 CFR 100 to 199 Department of Transportation Hazard-ous Ma

5、terials Regulations329 CFR 1919.1200 Department of Labor, OSHA Regula-tions on Hazard Communications33. Chemical Composition3.1 Technical grade ethylene dichloride shall conform to therequirements prescribed in Table 1.4. Packaging and Package Marking4.1 Package and label industrial or commercial qu

6、antities inaccordance with DOT regulations 49 CFR 100 to 199, and inaccordance with state and local regulations, and with OSHAregulations found in 29 CFR 1910.1200.5. Keywords5.1 ethylene dichloride;1,2-dichloroethaneASTM International takes no position respecting the validity of any patent rights a

7、sserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time

8、 by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will re

9、ceive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM In

10、ternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or thr

11、ough the ASTM website(www.astm.org).1This specification is under the jurisdiction of ASTM Committee D26 onHalogenated Organic Solvents and Fire Extinguishing Agents and is the directresponsibility of Subcommittee D26.02 on Vapor Degreasing.Current edition approved June 10, 2003. Published August 200

12、3. Originallyapproved in 1996. Last previous edition approved in 1997 as D 596097.2Annual Book of ASTM Standards, Vol 15.05.3The Code of Federal Regulations may be obtained from the Superintendent ofDocuments, U. S. Government Printing Office, Washington, DC 20402.TABLE 1 Technical Grade Ethylene Di

13、chloride RequirementsProperty Specification Test MethodColor, Pt-Co, max 10 D 2108Ethylene Dichloride, Weight %, min 99.8 D 6806Specific Gravity, 25/25C 1.2481.252 D 2111Acidity (as HCl), ppm, max 10 D 2989Water, ppm, max 200 D 34011Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.