ASTM D5164-2005(2011) Standard Specification for Propylene Glycol and Dipropylene Glycol《丙二醇和二丙基丙二醇的标准规范》.pdf

《ASTM D5164-2005(2011) Standard Specification for Propylene Glycol and Dipropylene Glycol《丙二醇和二丙基丙二醇的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5164-2005(2011) Standard Specification for Propylene Glycol and Dipropylene Glycol《丙二醇和二丙基丙二醇的标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D5164 05 (Reapproved 2011)Standard Specification forPropylene Glycol and Dipropylene Glycol1This standard is issued under the fixed designation D5164; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last re

2、vision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers propylene glycol and dipropy-lene glycol for use in the preparation of surface coatings.1.2 The fo

3、llowing applies to all specified limits in thisstandard; for purposes of determining conformance with thisstandard, an observed value or a calculated value shall berounded off “to the nearest unit” in the last right-hand digitused in expressing the specification limit, in accordance withthe rounding

4、-off method of Practice E29.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 For specific hazard information and guidance, see thesuppliers Material Safety Data Sheets.2. Referenced Documents2.1 ASTM Standards:2D1209 Test

5、 Method for Color of Clear Liquids (Platinum-Cobalt Scale)D4052 Test Method for Density, Relative Density, and APIGravity of Liquids by Digital Density MeterD5386 Test Method for Color of Liquids Using TristimulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine Conforman

6、ce with SpecificationsE202 Test Methods for Analysis of Ethylene Glycols andPropylene GlycolsE300 Practice for Sampling Industrial Chemicals2.2 U.S. Federal Specification:PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packagingof33. Properties3.1 Propylene glycol or dipropylene glycol shall conform t

7、othe respective properties shown in Table 1.4. Sampling4.1 The material shall be sampled in accordance withPractice E300.5. Test Methods5.1 The properties enumerated in this specification shall bedetermined in accordance with Test Methods E202.5.2 The apparent specific gravity can also be determined

8、 inaccordance with Test Method D4052.6. Packaging and Package Marking6.1 Package size shall be agreed upon between the pur-chaser and the supplier.6.2 Packaging shall conform to applicable carrier rules andregulations or when specified shall conform to Fed. Spec.PPP-C-2020.7. Keywords7.1 dipropylene

9、 glycol; propylene glycol1This specification is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates.Current edition approved Feb. 1, 2011. P

10、ublished February 2011. Originallyapproved in 1991. Last previous edition approved in 2005 as D5164 05. DOI:10.1520/D5164-05R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume informatio

11、n, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.TABLE 1 Requirements for Propylene Glycol and DipropyleneGlycolProperty Propyle

12、ne Glycol Dipropylene GlycolApparent specific gravity20/20C 1.0375 to 1.0390 1.020 to 1.025or or or25/25C 1.0351 to 1.0366 1.016 to 1.021Color, Pt-Co units, maxA15 15Distillation range, 760 mmHgInitial Boiling Point, C min 185 228Dry point, C, max 190 236Water, wt %, max 0.2 0.2Acidity, as acetic ac

13、id, wt %, max 0.005 0.01Propylene glycol, wt %, max NAB1.0Dipropylene glycol, wt %, max 1.0 NABTripropylene glycol, wt %, max NAB1.0Iron, ppm, max 0.5 1.0AInstrumental Pt-Co color determined by Test Method D5386 have been shownto have no statistically significant difference from Pt-Co color determin

14、ed by TestMethod D1209. However, it is not known whether n-butyl alcohol was part of thesample set included in the interlaboratory study.BNA = not applicable.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Cons

15、hohocken, PA 19428-2959, United States.SUMMARY OF CHANGESCommittee D01.35 has identified the location of selected changes to this standard since the last issue(D5164 91 (2000) that may impact the use of this standard.(1) Added reference to Practice E29 in Scope section.(2) Added Practice E29 and Tes

16、t Methods D1209 and D5386 tolist of Referenced Documents.(3) Changed specs limits for apparent specific gravity in Table1.(4) Added new Note A to Table 1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.

17、Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed ev

18、ery five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible tech

19、nical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohoc

20、ken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D5164 05 (2011)2