ASTM D86-2016a Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure《大气压力下石油产品和液体燃料蒸馏的标准试验方法》.pdf

《ASTM D86-2016a Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure《大气压力下石油产品和液体燃料蒸馏的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D86-2016a Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure《大气压力下石油产品和液体燃料蒸馏的标准试验方法》.pdf（35页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D86 16D86 16aStandard Test Method forDistillation of Petroleum Products and Liquid Fuels atAtmospheric Pressure1This standard is issued under the fixed designation D86; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, t

2、he year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This test method covers

3、the atmospheric distillation of petroleum products and liquid fuels using a laboratory batchdistillation unit to determine quantitatively the boiling range characteristics of such products as light and middle distillates,automotive spark-ignition engine fuels with or without oxygenates (see Note 1),

4、 aviation gasolines, aviation turbine fuels, dieselfuels, biodiesel blends up to 20 %, marine fuels, special petroleum spirits, naphthas, white spirits, kerosines, and Grades 1 and 2burner fuels.NOTE 1An interlaboratory study was conducted in 2008 involving 11 different laboratories submitting 15 da

5、ta sets and 15 different samples ofethanol-fuel blends containing 25 % volume, 50 % volume, and 75 % volume ethanol. The results indicate that the repeatability limits of these samplesare comparable or within the published repeatability of the method (with the exception of FBP of 75 % ethanol-fuel b

6、lends). On this basis, it can beconcluded that Test Method D86 is applicable to ethanol-fuel blends such as Ed75 and Ed85 (Specification D5798) or other ethanol-fuel blends withgreater than 10 % volume ethanol. See ASTM RR:D02-1694 for supporting data.21.2 The test method is designed for the analysi

7、s of distillate fuels; it is not applicable to products containing appreciablequantities of residual material.1.3 This test method covers both manual and automated instruments.1.4 Unless otherwise noted, the values stated in SI units are to be regarded as the standard. The values given in parenthese

8、s areprovided for information only.1.5 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause centralnervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Cautionshould be taken when handl

9、ing mercury and mercury containing products. See the applicable product Material Safety Data Sheet(MSDS) for details and EPAs websitehttp:/www.epa.gov/mercury/faq.htmfor additional information. Users should be awarethat selling mercury and/or mercury containing products into your state or country ma

10、y be prohibited by law.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior t

11、o use.2. Referenced Documents2.1 All standards are subject to revision, and parties to agreement on this test method are to apply the most recent edition ofthe standards indicated below, unless otherwise specified, such as in contractual agreements or regulatory rules where earlierversions of the me

12、thod(s) identified may be required.2.2 ASTM Standards:3D97 Test Method for Pour Point of Petroleum ProductsD323 Test Method for Vapor Pressure of Petroleum Products (Reid Method)1 This test method is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and

13、is the direct responsibility of SubcommitteeD02.08 on Volatility.In the IP, the equivalent test method is published under the designation IP 123. It is under the jurisdiction of the Standardization Committee.Current edition approved July 1, 2016Aug. 1, 2016. Published August 2016. Originally approve

14、d in 1921. Last previous edition approved in 20152016 asD86 15.D86 16. DOI: 10.1520/D0086-16.10.1520/D0086-16A.2 Supporting data have been filed at ASTM International Headquarters and may be obtained by requesting Research Report RR:D02-1694.3 For referencedASTM standards, visit theASTM website, www

15、.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of wha

16、t changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the

17、 official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D4057 Practice for Manual Sampling of Petroleum and Petroleum ProductsD4175 Terminology Relating to Pe

18、troleum Products, Liquid Fuels, and LubricantsD4177 Practice for Automatic Sampling of Petroleum and Petroleum ProductsD4953 Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)D5190 Test Method for Vapor Pressure of Petroleum Products (Automatic Method) (Withdrawn 2

19、012)4D5191 Test Method for Vapor Pressure of Petroleum Products (Mini Method)D5798 Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition EnginesD5842 Practice for Sampling and Handling of Fuels for Volatility MeasurementD5949 Test Method for Pour Point of Petroleum Produc

20、ts (Automatic Pressure Pulsing Method)D5950 Test Method for Pour Point of Petroleum Products (Automatic Tilt Method)D5985 Test Method for Pour Point of Petroleum Products (Rotational Method)D6300 Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and

21、 LubricantsD6708 Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purportto Measure the Same Property of a MaterialE1 Specification for ASTM Liquid-in-Glass ThermometersE77 Test Method for Inspection and Verification of ThermometersE1272 Specifi

22、cation for Laboratory Glass Graduated CylindersE1405 Specification for Laboratory Glass Distillation Flasks2.3 Energy Institute Standards:5IP 69 Determination of Vapour PressureReid MethodIP 123 Petroleum ProductsDetermination of Distillation CharacteristicsIP 394 Determination of Air Saturated Vapo

23、ur PressureIP Standard Methods for Analysis and Testing of Petroleum and Related Products 1996Appendix A3. Terminology3.1 Definitions:3.1.1 decomposition, nof a hydrocarbon, the pyrolysis or cracking of a molecule yielding smaller molecules with lowerboiling points than the original molecule.3.1.2 d

24、ecomposition point, nin distillation, the corrected temperature reading that coincides with the first indications ofthermal decomposition of the specimen.3.1.3 dry point, nin distillation, the corrected temperature reading at the instant the last drop of liquid evaporates from thelowest point in the

25、 flask.3.1.4 dynamic holdup, nin D86 distillation, the amount of material present in the neck of the flask, in the sidearm of the flask,and in the condenser tube during the distillation.3.1.5 emergent stem effect, nthe offset in temperature reading caused by the use of total immersion mercury-in-gla

26、ssthermometers in the partial immersion mode.3.1.5.1 DiscussionIn the partial immersion mode, a portion of the mercury thread, that is, the emergent portion, is at a lower temperature than theimmersed portion, resulting in a shrinkage of the mercury thread and a lower temperature reading.3.1.6 end p

27、oint (EP) or final boiling point (FBP), nthe maximum corrected thermometer reading obtained during the test.3.1.6.1 DiscussionThis usually occurs after the evaporation of all liquid from the bottom of the flask. The term maximum temperature is a frequentlyused synonym.3.1.7 front end loss, nloss due

28、 to evaporation during transfer from receiving cylinder to distillation flask, vapor loss duringthe distillation, and uncondensed vapor in the flask at the end of the distillation.3.1.8 fuel ethanol (Ed75-Ed85), nblend of ethanol and hydrocarbon of which the ethanol portion is nominally 75 % to 85 %

29、by volume denatured fuel ethanol. D41753.1.9 initial boiling point (IBP), nin D86 distillation, the corrected temperature reading at the instant the first drop ofcondensate falls from the lower end of the condenser tube.4 The last approved version of this historical standard is referenced on www.ast

30、m.org.5 Available from Energy Institute, 61 New Cavendish St., London, WIG 7AR, U.K., http:/www.energyinst.org.uk.D86 16a23.1.10 percent evaporated, nin distillation, the sum of the percent recovered and the percent loss.3.1.10.1 percent loss, n in distillation, one hundred minus the percent total r

31、ecovery.3.1.10.2 corrected loss, npercent loss corrected for barometric pressure.3.1.11 percent recovered, nin distillation, the volume of condensate collected relative to the sample charge.3.1.11.1 percent recovery, nin distillation, maximum percent recovered relative to the sample charge.3.1.11.2

32、corrected percent recovery, nin distillation, the percent recovery, adjusted for the corrected percent loss.3.1.11.3 percent total recovery, nin distillation, the combined percent recovery and percent residue.3.1.12 percent residue, nin distillation, the volume of residue relative to the sample char

33、ge.3.1.13 rate of change (or slope), nthe change in temperature reading per percent evaporated or recovered, as described in 13.2.3.1.14 sample charge, nthe amount of sample used in a test.3.1.15 temperature lag, nthe offset between the temperature reading obtained by a temperature sensing device an

34、d the truetemperature at that time.3.1.16 temperature measurement device, na thermometer, as described in 6.3.1, or a temperature sensor, as described in 6.3.2.3.1.16.1 temperature reading, nthe temperature obtained by a temperature measuring device or system that is equal to thethermometer reading

35、described in 3.1.16.3.3.1.16.2 corrected temperature reading, nthe temperature reading, as described in 3.1.16.1, corrected for barometric pressure.3.1.16.3 thermometer reading (or thermometer result), nthe temperature of the saturated vapor measured in the neck of theflask below the vapor tube, as

36、determined by the prescribed thermometer under the conditions of the test.3.1.16.4 corrected thermometer reading, nthe thermometer reading, as described in 3.1.16.3, corrected for barometricpressure.4. Summary of Test Method4.1 Based on its composition, vapor pressure, expected IBP or expected EP, o

37、r combination thereof, the sample is placed in oneof four groups. Apparatus arrangement, condenser temperature, and other operational variables are defined by the group in whichthe sample falls.4.2 A 100 mL specimen of the sample is distilled under prescribed conditions for the group in which the sa

38、mple falls. Thedistillation is performed in a laboratory batch distillation unit at ambient pressure under conditions that are designed to provideapproximately one theoretical plate fractionation. Systematic observations of temperature readings and volumes of condensate aremade, depending on the nee

39、ds of the user of the data. The volume of the residue and the losses are also recorded.4.3 At the conclusion of the distillation, the observed vapor temperatures can be corrected for barometric pressure and the dataare examined for conformance to procedural requirements, such as distillation rates.

40、The test is repeated if any specified conditionhas not been met.4.4 Test results are commonly expressed as percent evaporated or percent recovered versus corresponding temperature, eitherin a table or graphically, as a plot of the distillation curve.5. Significance and Use5.1 The basic test method o

41、f determining the boiling range of a petroleum product by performing a simple batch distillation hasbeen in use as long as the petroleum industry has existed. It is one of the oldest test methods under the jurisdiction of ASTMCommittee D02, dating from the time when it was still referred to as the E

42、ngler distillation. Since the test method has been in usefor such an extended period, a tremendous number of historical data bases exist for estimating end-use sensitivity on products andprocesses.5.2 The distillation (volatility) characteristics of hydrocarbons have an important effect on their saf

43、ety and performance,especially in the case of fuels and solvents. The boiling range gives information on the composition, the properties, and thebehavior of the fuel during storage and use.Volatility is the major determinant of the tendency of a hydrocarbon mixture to producepotentially explosive va

44、pors.5.3 The distillation characteristics are critically important for both automotive and aviation gasolines, affecting starting,warm-up, and tendency to vapor lock at high operating temperature or at high altitude, or both. The presence of high boiling pointcomponents in these and other fuels can

45、significantly affect the degree of formation of solid combustion deposits.5.4 Volatility, as it affects rate of evaporation, is an important factor in the application of many solvents, particularly those usedin paints.5.5 Distillation limits are often included in petroleum product specifications, in

46、 commercial contract agreements, processrefinery/control applications, and for compliance to regulatory rules.D86 16a36. Apparatus6.1 Basic Components of the Apparatus:6.1.1 The basic components of the distillation unit are the distillation flask, the condenser and associated cooling bath, a metalsh

47、ield or enclosure for the distillation flask, the heat source, the flask support, the temperature measuring device, and the receivingcylinder to collect the distillate.6.1.2 Figs. 1 and 2 are examples of manual distillation units.6.1.3 In addition to the basic components described in 6.1.1, automate

48、d units also are equipped with a system to measure andautomatically record the temperature and the associated recovered volume in the receiving cylinder.6.2 A detailed description of the apparatus is given in Annex A2.6.3 Temperature Measuring Device:6.3.1 Mercury-in-glass thermometers, if used, sha

49、ll be filled with an inert gas, graduated on the stem and enamel backed. Theyshall conform to Specification E1 or IP Standard Methods for Analysis and Testing of Petroleum and Related Products1996AppendixA, or both, for thermometersASTM 7C/IP 5C andASTM 7F for the low range thermometers, andASTM 8C/IP6C and ASTM 8F for the high range thermometers.6.3.1.1 Thermometers that have been exposed for an extended period above an observed temperature of 370 C shall not bereused without a verification of the ice point or checked as prescribed in Sp