ASTM C1503-2001 Standard Specification for Silvered Flat Glass Mirror《镀银平镜的标准规范》.pdf

《ASTM C1503-2001 Standard Specification for Silvered Flat Glass Mirror《镀银平镜的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1503-2001 Standard Specification for Silvered Flat Glass Mirror《镀银平镜的标准规范》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 1503 01Standard Specification forSilvered Flat Glass Mirror1This standard is issued under the fixed designation C 1503; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthes

2、es indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the requirements for silveredflat glass mirrors of rectangular shape supplied as cut sizes,stock sheets or as lehr ends and to

3、which no further processing(such as edgework or other fabrication) has been done.1.2 This specification covers the quality requirements ofsilvered annealed monolithic clear and tinted flat glass mirrorsupto6mm(14 in.) thick. The mirrors are intended to be usedindoors for mirror glazing, for componen

4、ts of decorativeaccessories or for similar uses.1.3 This specification does not address safety glazing ma-terials nor requirements for mirror applications. Consult modelbuilding codes and other applicable standards for safetyglazing applications.1.4 Mirrors covered in this specification are not inte

5、nded foruse in environments where high humidity or airborne corrosionpromoters, or both, are consistently present (such as swimmingpool areas, ocean-going vessels, chemical laboratories andother corrosive environments).1.5 The dimensional values stated in metric units are to beregarded as the standa

6、rd. The inch-pound units given inparentheses are for information only.1.6 The following safety hazards caveat pertains only to thetest method portion Section 7 of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the respon

7、sibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory require-ments prior to use.2. Referenced Documents2.1 Reference to these documents shall be the latest issueunless otherwise specified by the authority applying this

8、specification:2.2 ASTM Standards:B 117 Practice for Operating Salt Spray (Fog) Apparatus2C 162 Terminology of Glass glazing; mirror; reflectance; reflective coating;silveredThe American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in conne

9、ctionwith any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any suchpatent rights, and the risk of infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsi

10、ble technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Headquarters. Your comments will receive careful consideration at

11、 a meeting of the responsibletechnical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make yourviews known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM, 100 Barr Harbor Drive, PO Box C

12、700, West Conshohocken, PA 19428-2959, United States.Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website (www.astm.org).C 15035