ASTM B745 B745M-2012 Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains《下水道和排水系统用波纹铝管的标准规格》.pdf

《ASTM B745 B745M-2012 Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains《下水道和排水系统用波纹铝管的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B745 B745M-2012 Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains《下水道和排水系统用波纹铝管的标准规格》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B745/B745M 97 (Reapproved 2005) B745/B745M 12Standard Specification forCorrugated Aluminum Pipe for Sewers and Drains1This standard is issued under the fixed designation B745/B745M; the number immediately following the designation indicates the yearof original adoption or, in the case o

2、f revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers corrugated aluminum pipe intended for use for storm water drainage,

3、underdrains, the constructionof culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrialwastes.1.2 This specification does not include requirements for bedding, backfill, or the relationship between earth-cover load and sheetthi

4、ckness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection ofsheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The purchaser mustcorrelate the above factors and also the co

5、rrosion and abrasion requirements of the field installation with the sheet thickness. Thestructural design of corrugated aluminum pipe and the proper installation procedures are given in Practices B790/B790M andB788/B788M, respectively. A procedure for using life-cycle cost analysis techniques to ev

6、aluate alternative drainage systemdesigns using corrugated metal pipe is given in Practice A930.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used i

7、ndependently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate saf

8、ety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareA307 Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile StrengthA563

9、 Specification for Carbon and Alloy Steel NutsA563M Specification for Carbon and Alloy Steel Nuts (Metric)A930 Practice for Life-Cycle Cost Analysis of Corrugated Metal Pipe Used for Culverts, Storm Sewers, and Other BuriedConduitsB209 Specification for Aluminum and Aluminum-Alloy Sheet and PlateB20

10、9M Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and TubesB221M Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)B316/B316M Specificatio

11、n for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and RodsB633 Specification for Electrodeposited Coatings of Zinc on Iron and SteelB666/B666M Practice for Identification Marking of Aluminum and Magnesium ProductsB695 Specification for Coatings of Zinc Mechanically Deposited on Iron and

12、SteelB744/B744M Specification for Aluminum Alloy Sheet for Corrugated Aluminum PipeB788/B788M Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe1 This specification is under the jurisdiction of ASTM Committee B07 on Light Metals and Alloys and is the direct respon

13、sibility of Subcommittee B07.08 on CorrugatedAluminum Pipe and Corrugated Aluminum Structural Plate.Current edition approved Sept. 1, 2005Nov. 1, 2012. Published September 2005 December 2012. Originally approved in 1985. Last previous edition approved in 19972005as B745/B745M 97.B745/B745M 97 (2005)

14、. DOI: 10.1520/B0745_B0745M-97R05.10.1520/B0745_B0745M-12.2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.

15、This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior edi

16、tions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-295

17、9. United States1B790/B790M Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, StormSewers, and Other Buried ConduitsC443 Specification for Joints for Concrete Pipe and Manholes, Using Rubber GasketsD1056 Specification for Flexible Cellular MaterialsSpo

18、nge or Expanded RubberF467 Specification for Nonferrous Nuts for General UseF467M Specification for Nonferrous Nuts for General Use (Metric)F468 Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General UseF468M Specification for Nonferrous Bolts, Hex Cap Scre

19、ws, and Studs for General Use (Metric)F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric) (Withdrawn 2012)3F593 Specification for Stainless Steel Bolts, Hex Cap Screws, and StudsF594 Specification for Stainless Steel NutsF738M Specification for Stainless Stee

20、l Metric Bolts, Screws, and StudsF836M Specification for Style 1 Stainless Steel Metric Nuts (Metric)2.2 AASHTO Standard:4T 249 Test for Helical Lock Seam Corrugated Pipe3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 fabricatorthe producer of the pipe.3.1.2 manufacturerthe pr

21、oducer of the sheet.3.1.3 purchaserthe purchaser of the finished product.4. Classification4.1 The corrugated aluminum pipe covered by this specification is classified as follows:4.1.1 Type IThis pipe shall have a full circular cross-section, with a single thickness of corrugated sheet, fabricated wi

22、thannular (circumferential) or helical corrugations.4.1.2 Type IAThis pipe shall have a full circular cross-section, with an outer shell of corrugated sheet and an inner liner ofsmooth (uncorrugated) sheet, fabricated with helical corrugations and lock seams.4.1.3 Type IRThis pipe shall have a full

23、circular cross-section, with a single thickness of smooth sheet, fabricated with helicalribs projecting outwardly.4.1.4 Type IIThis pipe shall be a Type I pipe which has been reformed into a pipe-arch, having an approximately flat bottom.4.1.5 Type IIAThis pipe shall be a Type IA pipe which has been

24、 reformed into a pipe-arch, having an approximately flatbottom.4.1.6 Type IIRThis pipe shall be a Type IR pipe which has been reformed into a pipe-arch, having an approximately flatbottom.4.1.7 Type IIIThis pipe, intended for use as underdrains or for underground disposal of water, shall be a Type I

25、 pipe whichhas been perforated to permit the in-flow or out-flow of water.4.1.8 Type IIIRThis pipe, intended for the underground disposal of water or for subsurface drainage, shall be a Type IR pipewhich has been perforated to permit the outflow or inflow of water.4.2 Perforations in Type III pipe a

26、re classified as Class 1 or Class 2 and perforations in Type IIIR pipe are classified as Class4, as described in 8.3.2.5. Ordering Information5.1 Orders for material to this specification shall include the following information as necessary, to adequately describe thedesired product:5.1.1 Name of ma

27、terial (corrugated aluminum pipe),5.1.2 ASTM designation and year of issue, as B745-_ for inch-pound units or B745M-_ for SI units,5.1.3 Type of pipe (4.1),5.1.4 Method of fabrication for Type I and Type II pipe (7.1),5.1.5 Diameter of circular pipe (8.1.1), or span and rise of pipe-arch section (8.

28、2.1),5.1.6 Length, either total length or length of each piece and number of pieces,5.1.7 Description of corrugations (7.2),5.1.8 Sheet thickness (8.1.2),5.1.9 Coupling bands, number, and type (9.1) if special type is required,3 The last approved version of this historical standard is referenced on

29、www.astm.org.4 Available from American Association of State Highway and Transportation Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001.B745/B745M 1225.1.10 Gaskets for coupling bands, if required (9.3),5.1.11 For perforated pipe, the class of perforations. If no class is

30、specified for Type III pipe, Class 1 perforations will befurnished. Type IIIR pipe is furnished with Class 4 perforations only (8.3.2.1 and 8.3.2.3),5.1.12 Certification, if required (13.1), and5.1.13 Special requirements.6. Materials6.1 Aluminum Sheet for PipeAll pipe fabricated under this specific

31、ation shall be formed from aluminum-alloy sheetconforming to Specification B744/B744M.6.2 Aluminum Sheet for Coupling BandsThe sheet used in fabricating coupling bands shall conform to SpecificationB744/B744M.6.3 RivetsThe material used for rivets in riveted pipe shall conform to the requirements of

32、 Specification B316/B316M foralloy 6053-T4, with 6053-T61 and alloy 5056 H32, to meet or exceed the following mechanical properties:Tensile Strength, min, ksi MPa 25 170Yield Strength, min, ksi MPa 14 95Shear Strength, min, ksi MPa 15 105Elongation in 2 in., 50 mm, or 4x dia., min, % 16Elongation in

33、 2 in., 50 mm, or 4x dia., min, % 14 95If bolts and nuts are substituted for rivets (see 7.3.1), they shall meet the following requirements for either steel bolts and nuts,stainless steel bolts and nuts, or aluminum alloy bolts and nuts:Bolts NutsFor B745 pipe(Steel) A307 A563, Gr. A(Stainless Steel

34、) F593, Alloy Grp 1, 2, or 3 F594, Alloy Grp 1, 2, or 3(Aluminum Alloy) F468, Alloy 6061-T6 F467, Alloy 6061-T6For B745M pipe(Steel)(Stainless Steel)F568M, Cl. 4.6F738M, Alloy Grp A1, A2,or A4A563M, Cl. 5F836M, Alloy Grp A1, A2,or A4(Aluminum Alloy) F468M, Alloy 6061-T6 F467M, Alloy 6061-T6The steel

35、 bolts and nuts shall be hot-dip galvanized in conformance with Specification A153/A153M, or be mechanicallygalvanized in conformance with Specification B695 Class 40.6.4 Hardware for Coupling BandsBolts and nuts for coupling bands shall conform to the requirements shown in 6.3 exceptfor the coating

36、 on steel bolts and nuts. Steel bolts, nuts, and other threaded steel items used with coupling bands shall be zinc coatedby one the following processes: hot-dip process as provided in Specification A153/A153M, electroplating process as provided inSpecification B633 Class FE/ZN 8, or mechanical proce

37、ss as provided in Specification B695 Class 8. Other steel hardware itemsused with coupling bands shall be zinc-coated by one of the following processes: hot-dip process as provided in SpecificationA153/A153M; electroplating process as provided in Specification B633 Class FE/ZN 25; or mechanical proc

38、ess as provided inSpecification B695 Class 25. Aluminum angles and lugs shall conform to the requirements of Specification B221 or B221M foralloy 6063-T6.6.5 GasketsIf gaskets are used in couplings, they shall be a band of expanded rubber meeting the requirements ofSpecification D1056 for the “RE” c

39、losed cell grades, or O-rings meeting the requirements of Specification C443.7. Fabrication7.1 General RequirementsPipe shall be fabricated in full circular cross-section.7.1.1 Type I pipe shall have annular corrugations with lap joints fastened with rivets or shall have helical corrugations with ac

40、ontinuous lock seam extending from end to end of each length of pipe. As there are important differences in the structuralcharacteristics of annular, riveted pipe versus helical pipe, it is important for the purchaser to stipulate, for Type I and Type II pipe,the method of fabrication desired. If th

41、e method of fabrication is not stated in the ordering information, the fabrication method shallbe at the option of the fabricator.7.1.2 Type IA pipe shall be fabricated with a smooth liner and helically corrugated shell integrally attached at helical lock seamsextending from end to end of each lengt

42、h of pipe. The shell shall have corrugations of nominal 223 (or 3 in. 68 or 75 mm pitch.7.1.3 Type IR pipe shall be fabricated with helical ribs projecting outward with a continuous lock seam extending from end toend of each length of pipe.7.2 CorrugationsThe corrugations shall be either annular or

43、helical as provided in 7.1. The direction of the crests and valleysof helical corrugations shall not be less than 60 from the axis of the pipe for pipe diameters larger than 21 in. 525 mm, and notless than 45 from the axis for pipe diameters of 21 in. 525 mm and smaller.7.2.1 For Type I and IA pipe,

44、 corrugations shall form smooth continuous curves and tangents. The dimensions of thecorrugations shall be in accordance with Table 1 for the size indicated in the order.B745/B745M 1237.2.2 For Type IR pipe, the corrugations shall be essentially rectangular ribs projecting outward from the pipe wall

45、. Thedimensions and spacings of the ribs shall be in accordance with Table 2 for the size indicated in the order. See also Fig. 1. Forthe 1112 in. 292 mm rib spacing, a stiffener shall be included midway between the ribs, if the sheet between the ribs does notinclude a lock seam. This stiffener shal

46、l have a nominal radius of 0.25 in. 6.4 mm and a minimum height of 0.20 in. 5.1 mmtoward the outside of the pipe.NOTE 1The nominal dimensions and properties for smooth corrugations and for ribs are given in Practice B790/B790M.7.3 Riveted SeamsThe longitudinal seams shall be staggered to the extent

47、that no more than three thicknesses of sheet arefastened by any rivet. Pipe to be reformed into pipe-arch shape shall also meet the longitudinal seam requirement of 8.2.2.NOTE 2Fabrication of pipe without longitudinal seams in 120 of arc, so that the pipe may be installed without longitudinal seams

48、in the invert, issubject to negotiation between the purchaser and fabricator.7.3.1 The size of rivets, number per corrugation, and width of lap at the longitudinal seam shall be as stated in Table 3,depending on sheet thickness, corrugation size, and diameter of pipe. For pipe with 1 in. 25 mm deep

49、corrugations, 12-in. MetricM12 diameter bolts and nuts may be used in lieu of rivets on a one-for-one replacement ratio. Circumferential seams shall beriveted using rivets of the same size as for longitudinal seams and shall have a maximum rivet spacing of 6 in. 150 mm, measuredon centers, except that six rivets will be sufficient in 12-in. 300-mm diameter pipe.TABLE 1 Corrugation Requirements for Type I, IA, II, IIA, and IIIPipeNominal Size MaximumPitchA MinimumDepthB Inside RadiusCNominal MinimumB745 (in.)112 by