ASTM B744 B744M-2015 Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe《波纹铝管用铝金属薄板的标准规格》.pdf

《ASTM B744 B744M-2015 Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe《波纹铝管用铝金属薄板的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B744 B744M-2015 Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe《波纹铝管用铝金属薄板的标准规格》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B744/B744M 05 (Reapproved 2011)B744/B744M 15Standard Specification forAluminum Alloy Sheet for Corrugated Aluminum Pipe1This standard is issued under the fixed designation B744/B744M; the number immediately following the designation indicates the yearof original adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers aluminum alloy sheets used in the fabrication of corrugated alumi

3、num pipe intended for use forstorm water drainage, underdrains, culverts, and similar uses. The material is furnished corrugated in cut lengths, and uncorrugatedin coils and cut lengths.1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the

4、 text, the SI unitsare shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be usedindependently of the other. Combining values from the two systems may result in nonconformance with the standard.1.3 This standard does not purport to address all

5、 of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B209 Specification for

6、Aluminum and Aluminum-Alloy Sheet and PlateB209M Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)B666/B666M Practice for Identification Marking of Aluminum and Magnesium Products2.2 American National Standards:2H35.2 Dimensional Tolerances for Aluminum Mill ProductsH35.2M Dimen

7、sional Tolerances for Aluminum Mill Products Metric3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 fabricatorfabricator, nthe producer of the pipe.3.1.2 manufacturermanufacturer, nthe producer of the sheet.3.1.3 purchaserpurchaser, nthe purchaser of the finished pipe.4. Orderi

8、ng Information4.1 Orders for materials under this specification shall include the following information:4.1.1 Name of material (aluminum alloy sheet for corrugated aluminum pipe),4.1.2 This specification designation (including number, year, and revision letter if applicable), as ASTM B744 _ forinch-

9、pound units or ASTM B744M _ for SI units, and4.1.3 Specified sheet thickness, using only those thicknesses listed in Table 1.4.1.4 For sheet ordered in coils:4.1.4.1 Sheet width,4.1.4.2 Coil size requirements (specify maximum outside diameter (OD), acceptable inside diameter (ID), and maximumweight)

10、, and4.1.4.3 Total quantity (mass).1 This specification is under the jurisdiction of ASTM Committee B07 on Light Metals and Alloys and is the direct responsibility of Subcommittee B07.08 on CorrugatedAluminum Pipe and Corrugated Aluminum Structural Plate.Current edition approved May 1, 2011May 1, 20

11、15. Published May 2011May 2015. Originally approved in 1985. Last previous edition approved in 20052011 asB744/B744M 05.B744/B744M 05 (2011). DOI: 10.1520/B0744_B0744M-05R11.10.1520/B0744_B0744M-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service a

12、t serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous ver

13、sion. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes sec

14、tion appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.5 For sheet ordered flat in cut lengths:4.1.5.1 Sheet width and length,4.1.5.2 Total quantity (mass or number of sheets), and4.1.5.3 Maximum m

15、ass or number of sheets in a lift.4.1.6 For sheet ordered corrugated:4.1.6.1 Sheet width (overall) and length,4.1.6.2 Corrugation size (pitch and depth) (see 8.4),4.1.6.3 Total quantity (mass or number of sheets), and4.1.6.4 Maximum mass or number of sheets in a lift.4.2 Additionally, orders for mat

16、erials under this specification shall include the following information when requested by thepurchaser:4.2.1 Whether certification is required.NOTE 1Typical ordering descriptions are as follows: (1) Aluminum alloy sheet for corrugated aluminum pipe, conforming to ASTM B744 _;0.060-in. thickness; 100

17、0 sheets, 2512 by 60 in., with 223 by 12 in. corrugations; maximum 300 sheets per lift. (2) Aluminum alloy sheet for corrugatedaluminum pipe, conforming to ASTM B744M _; 2.67-mm2.67 mm thickness by 760-mm760 mm width; 25 000 kg total; coils 1200 mm OD max,600 mm ID min, 5000 kg max each coil; certif

18、ied with test report.5. Chemical Composition5.1 The sheet material shall conform to the chemical composition limits in Specifications B209 B209M.6. Mechanical Requirements6.1 The sheet material shall conform to the requirements for mechanical properties specified in Specification B209 B209M,when tes

19、ted prior to corrugating or other fabrication.NOTE 2Sheet material tested after corrugating and other fabricating should conform to the specified tensile and yield strength requirements, but dueto cold working, conformance to the elongation requirements may not be obtained.7. General Requirements7.1

20、 Aluminum alloy sheets or coils supplied under this specification shall conform to the applicable requirements ofSpecification B209 B209M (as appropriate) for alclad alloy 3004-H34 for riveted pipe pipe, and either alclad alloy 3004-H34or alclad alloy 3004H32 for helical pipe, but limited to only al

21、clad alloy 3004-H32 for production of spiral rib pipe.8. Dimensions and Tolerances8.1 Sheet thickness shall conform to dimensions prescribed in Table 1.8.2 The thickness of cladding shall be as specified in Specification B209 B209M.8.3 Permissible variations in flat width, length and squareness shal

22、l be in accordance with ANSI H35.2 H35.2M.8.4 Corrugations shall form smooth continuous curves and tangents. The dimensions of the corrugations shall be in accordancewith Table 2.TABLE 1 Sheet ThicknessASpecified Thickness Minimum Thicknessin. mm in. mm0.048 1.22 0.045 1.140.060 1.52 0.057 1.440.075

23、 1.91 0.072 1.820.105 2.67 0.101 2.550.135 3.43 0.130 3.290.164 4.17 0.158 3.99TABLE 1 Sheet ThicknessASpecified Thickness Minimum Thicknessin. mm in. mm0.048 1.22 0.045 1.140.060 1.52 0.057 1.440.075 1.91 0.072 1.820.105 2.67 0.101 2.550.135 3.43 0.130 3.290.164 4.17 0.158 3.99A Thickness is measur

24、ed at any point on the sheet not less than 38 in. or 10 mmfrom an edge, and if corrugated, on the tangents of corrugations.B744/B744M 1528.5 Covering width of corrugated sheet shall be in accordance with Table 3. Covering width is the distance between the crestsof the extreme corrugations. There is

25、no established tolerance for overall width since the covering width and lip dimensions arethe governing factors for the formed product. The lip dimension of corrugated sheet shall be in accordance with Table 4. Thisdimension is measured along the radial curvature from the crest of the corrugation to

26、 the edge of the sheet.9. Sampling and Testing9.1 Sampling and testing shall be according to Specification B209 B209M. The manufacturer shall make adequate tests andmeasurements to ensure that the material produced complies with this specification.9.1.1 Test results including chemical composition, m

27、echanical properties, and cladding thickness shall be maintained by thesheet manufacturer for seven years and shall be made available to the fabricator and purchaser upon request, for examination atthe manufacturers facility unless otherwise agreed upon.9.2 The fabricator or the purchaser may make s

28、uch tests as are necessary to determine the acceptability of the material or toverify the correctness of a certification.9.3 Mechanical properties shall be determined on sheet prior to corrugating or other fabricating, except tests may be made afterfabrication by the purchaser for tensile and yield

29、strengths.10. Rejection10.1 Material tested by the purchaser and found not conforming to this specification may be rejected.11. Certification11.1 When specified in the purchase order or contract, a manufacturers certification shall be furnished to the purchaser of thesheet (fabricator) or to the pur

30、chaser of the finished pipe stating that samples representing each lot have been tested and inspectedin accordance with this specification and the requirements have been met. When specified in the purchase order or contract, a reportof the mechanical test results and the chemical composition limits

31、shall be furnished.TABLE 2 Corrugation RequirementsNominal Size Maximum PitchA Minimum DepthB Inside RadiusNominal MinimumB744All values in in.223 by 12 278 0.48 11/16 0.53 by 1 314 0.95 9/16 0.5B744MAll values in mm68 by 13 73 12 17 1275 by 25 83 24 14 12TABLE 2 Corrugation RequirementsNominal Size

32、 Maximum PitchA Minimum DepthB Inside RadiusNominal MinimumB744All values in in.223 by 12 278 0.48 11/16 0.53 by 1 314 0.95 9/16 0.5B744MAll values in mm68 by 13 73 12 17 1275 by 25 83 24 14 12A Pitch is measured from crest to crest of corrugations, at 90 to the direction of the corrugations.B Depth

33、 is measured as the vertical distance from a straightedge resting on the corrugation crests to the bottom of the intervening valley.TABLE 3 Covering Width Tolerance For Corrugated SheetCovering Width, in. mmTolerance Overand Underin. mmTo 24 610, inclusive 14 6.5Over 24 610 to 36 915, inclusive 38 9

34、.5Over 36 915 to 48 1220, inclusive 12 13TABLE 3 Covering Width Tolerance For Corrugated SheetCovering Width, in. mmTolerance Overand Underin. mmTo 24 610, inclusive 14 6.5Over 24 610 to 36 915, inclusive 38 9.5Over 36 915 to 48 1220, inclusive 12 13B744/B744M 153NOTE 3As the identity of the sheet i

35、s not maintained from the original ingot production, if numerical results are required by the purchaser, tests shouldbe performed on the finished sheet.12. Product Marking12.1 Each corrugated sheet furnished for use in annular corrugated pipe shall be identified by the sheet manufacturer showingthe

36、following:12.1.1 Name or trademark of sheet manufacturer,12.1.2 Alloy and temper,12.1.3 Specified thickness,12.1.4 Date of corrugating by a six-digit number indicating in order the year, month, and day of the month, and12.1.5 ASTM designation number.12.2 Coils and cut-length flat sheets shall be sim

37、ilarly marked by the manufacturer (except 12.1.4) at 2 to 5-ft 0.6 to 1.5 mintervals, or the information shall be included on a tag so that the fabricator can mark the sheet at the time of fabrication.12.3 The marking shall be applied to the sheet by a permanent method such as coining in accordance

38、with PracticeB666/B666M.13. Keywords13.1 aluminum pipe; aluminum sheet; culvertSUMMARY OF CHANGESCommittee B07B07 on Light Metals andAlloys has identified the locationslocation of selected changes to thisstandardsstandard since the last issue (insertB744/B744M 99) designation and year date) that may

39、 impact itsuse.the use of this standard. (May 1, 2015.)(1) Deleted the reference to the helical (corrugation) for the 3004H34 alclad alloy in Section 7. 3004H32 is the only temper beingused by the fabricators for helical corrugated aluminum pipe.(1) Revised subsection 7.1(2) Deleted the 0.036 specif

40、ied thickness from Table 1. This thickness of sheet is not being used.(3) Deleted the 6 by 1in. and 150 by 25 mm corrugation from Table 2. this is an unstable corrugation in aluminum and has notbeen fabricated for many years.TABLE 4 Corrugated Sheet Lip DimensionsNominal CorrugationSizeLip Dimension

41、Minimum Maximumin. mm in. mm in. mm223 by 12 68 by 13 34 19 1516 243 by 1 75 by 25 78 22 118 28TABLE 4 Corrugated Sheet Lip DimensionsNominal CorrugationSizeLip DimensionMinimum Maximumin. mm in. mm in. mm223 by 12 68 by 13 34 19 1516 243 by 1 75 by 25 78 22 118 28B744/B744M 154ASTM International ta

42、kes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own r

43、esponsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addres

44、sed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at th

45、e address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 155