ASTM B744 B744M-2005 Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe《波纹铝管用铝合金薄板的标准规范》.pdf

《ASTM B744 B744M-2005 Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe《波纹铝管用铝合金薄板的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM B744 B744M-2005 Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe《波纹铝管用铝合金薄板的标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 744/B 744M 05Standard Specification forAluminum Alloy Sheet for Corrugated Aluminum Pipe1This standard is issued under the fixed designation B 744/B 744M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of l

2、ast revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers aluminum alloy sheets used inthe fabrication of corrugated aluminum pipe intended for usefo

3、r storm water drainage, underdrains, culverts, and similaruses. The material is furnished corrugated in cut lengths, anduncorrugated in coils and cut lengths.1.2 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown

4、in brackets. The values stated in eachsystem are not exact equivalents; therefore, each system shallbe used independently of the other. Combining values from thetwo systems may result in nonconformance with the standard.1.3 This standard does not purport to address all of thesafety concerns, if any,

5、 associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B 209 Specification for Aluminum and Aluminum-AlloyS

6、heet and PlateB 209M Specification for Aluminum and Aluminum-AlloySheet and Plate MetricB 666/B 666M Practice for Identification Marking of Alu-minum and Magnesium Products2.2 American National Standards:2H35.2 Dimensional Tolerances for Aluminum Mill ProductsH35.2M Dimensional Tolerances for Alumin

7、um Mill Prod-ucts Metric3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 fabricatorthe producer of the pipe.3.1.2 manufacturerthe producer of the sheet.3.1.3 purchaserthe purchaser of the finished pipe.4. Ordering Information4.1 Orders for materials under this specification sha

8、ll in-clude the following information:4.1.1 Name of material (aluminum alloy sheet for corru-gated aluminum pipe),4.1.2 This specification designation (including number,year, and revision letter if applicable), as ASTM B 744 _for inch-pound units orASTM B 744M _ for SI units, and4.1.3 Specified shee

9、t thickness, using only those thicknesseslisted in Table 1.4.1.4 For sheet ordered in coils:4.1.4.1 Sheet width,4.1.4.2 Coil size requirements (specify maximum outsidediameter (OD), acceptable inside diameter (ID), and maximumweight), and4.1.4.3 Total quantity (mass).4.1.5 For sheet ordered flat in

10、cut lengths:4.1.5.1 Sheet width and length,4.1.5.2 Total quantity (mass or number of sheets), and4.1.5.3 Maximum mass or number of sheets in a lift.4.1.6 For sheet ordered corrugated:4.1.6.1 Sheet width (overall) and length,4.1.6.2 Corrugation size (pitch and depth) (see 8.4),4.1.6.3 Total quantity

11、(mass or number of sheets), and4.1.6.4 Maximum mass or number of sheets in a lift.4.2 Additionally, orders for materials under this specifica-tion shall include the following information when requested bythe purchaser:4.2.1 Whether certification is required.NOTE 1Typical ordering descriptions are as

12、 follows: (1) Aluminumalloy sheet for corrugated aluminum pipe, conforming to ASTMB 744 _; 0.060-in. thickness; 1000 sheets, 2512 by 60 in., with 223by12 in. corrugations; maximum 300 sheets per lift. (2) Aluminum alloysheet for corrugated aluminum pipe, conforming to ASTMB 744M _; 2.67-mm thickness

13、 by 760-mm width; 25 000 kg total;coils 1200 mm OD max, 600 mm ID min, 5000 kg max each coil; certifiedwith test report.1This specification is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibility of Subcommittee B07.08 onAluminum Culvert.Current edi

14、tion approved June 1, 2005. Published June 2005. Originallyapproved in 1985. Last previous edition approved in 1999 as B 744/B 744M 99.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume inf

15、ormation, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Chemical Composition5.1 The sheet material

16、 shall conform to the chemical com-position limits in Specifications B 209 B 209M.6. Mechanical Requirements6.1 The sheet material shall conform to the requirements formechanical properties specified in Specification B 209B 209M, when tested prior to corrugating or other fabrica-tion.NOTE 2Sheet mat

17、erial tested after corrugating and other fabricatingshould conform to the specified tensile and yield strength requirements,but due to cold working, conformance to the elongation requirements maynot be obtained.7. General Requirements7.1 Aluminum alloy sheets or coils supplied under thisspecificatio

18、n shall conform to the applicable requirements ofSpecification B 209 B 209M (as appropriate) for alclad alloy3004-H34 for riveted pipe or alclad alloy 3004H32 for helicalpipe.8. Dimensions and Tolerances8.1 Sheet thickness shall conform to dimensions prescribedin Table 1.8.2 The thickness of claddin

19、g shall be as specified inSpecification B 209 B 209M.8.3 Permissible variations in flat width, length and square-ness shall be in accordance with ANSI H35.2 H35.2M.8.4 Corrugations shall form smooth continuous curves andtangents. The dimensions of the corrugations shall be inaccordance with Table 2.

20、8.5 Covering width of corrugated sheet shall be in accor-dance with Table 3. Covering width is the distance between thecrests of the extreme corrugations. There is no establishedtolerance for overall width since the covering width and lipdimensions are the governing factors for the formed product.Th

21、e lip dimension of corrugated sheet shall be in accordancewith Table 4. This dimension is measured along the radialcurvature from the crest of the corrugation to the edge of thesheet.9. Sampling and Testing9.1 Sampling and testing shall be according to SpecificationB 209 B 209M. The manufacturer sha

22、ll make adequate testsand measurements to ensure that the material produced com-plies with this specification.9.1.1 Test results including chemical composition, mechani-cal properties, and cladding thickness shall be maintained bythe sheet manufacturer for seven years and shall be madeavailable to t

23、he fabricator and purchaser upon request, forexamination at the manufacturers facility unless otherwiseagreed upon.9.2 The fabricator or the purchaser may make such tests asare necessary to determine the acceptability of the material orto verify the correctness of a certification.9.3 Mechanical prop

24、erties shall be determined on sheetprior to corrugating or other fabricating, except tests may bemade after fabrication by the purchaser for tensile and yieldstrengths.10. Rejection10.1 Material tested by the purchaser and found not con-forming to this specification may be rejected.11. Certification

25、11.1 When specified in the purchase order or contract, amanufacturers certification shall be furnished to the purchaserof the sheet (fabricator) or to the purchaser of the finished pipestating that samples representing each lot have been tested andinspected in accordance with this specification and

26、the require-ments have been met. When specified in the purchase order orcontract, a report of the mechanical test results and thechemical composition limits shall be furnished.NOTE 3As the identity of the sheet is not maintained from the originalingot production, if numerical results are required by

27、 the purchaser, testsTABLE 1 Sheet ThicknessASpecified Thickness Minimum Thicknessin. mm in. mm0.048 1.22 0.045 1.140.060 1.52 0.057 1.440.075 1.91 0.072 1.820.105 2.67 0.101 2.550.135 3.43 0.130 3.290.164 4.17 0.158 3.99AThickness is measured at any point on the sheet not less than38 in. or 10 mmfr

28、om an edge, and if corrugated, on the tangents of corrugations.TABLE 2 Corrugation RequirementsNominal Size Maximum PitchAMinimum DepthBInside RadiusNominal MinimumB744All values in in.223 by12 278 0.48 11/16 0.53by1 314 0.95 9/16 0.5B744MAll values in mm68 by 13 73 12 17 1275 by 25 83 24 14 12APitc

29、h is measured from crest to crest of corrugations, at 90 to the direction of the corrugations.BDepth is measured as the vertical distance from a straightedge resting on the corrugation crests to the bottom of the intervening valley.TABLE 3 Covering Width Tolerance For Corrugated SheetCovering Width,

30、 in. mmTolerance Overand Underin. mmTo 24 610, inclusive14 6.5Over 24 610 to 36 915, inclusive38 9.5Over 36 915 to 48 1220, inclusive12 13B 744/B 744M 052should be performed on the finished sheet.12. Product Marking12.1 Each corrugated sheet furnished for use in annularcorrugated pipe shall be ident

31、ified by the sheet manufacturershowing the following:12.1.1 Name or trademark of sheet manufacturer,12.1.2 Alloy and temper,12.1.3 Specified thickness,12.1.4 Date of corrugating by a six-digit number indicatingin order the year, month, and day of the month, and12.1.5 ASTM designation number.12.2 Coi

32、ls and cut-length flat sheets shall be similarlymarked by the manufacturer (except 12.1.4) at 2 to 5-ft 0.6 to1.5 m intervals, or the information shall be included on a tagso that the fabricator can mark the sheet at the time offabrication.12.3 The marking shall be applied to the sheet by apermanent

33、 method such as coining in accordance with PracticeB 666/B 666M.13. Keywords13.1 aluminum pipe; aluminum sheet; culvertSUMMARY OF CHANGESCommittee B07 on Light Metals and Alloys has identified the locations of selected changes to this standardssince the last issue (B 744/B 744M 99) that may impact i

34、ts use.(1) Deleted the reference to the helical (corrugation) for the3004H34 alclad alloy in Section 7. 3004H32 is the onlytemper being used by the fabricators for helical corrugatedaluminum pipe.(2) Deleted the 0.036 specified thickness from Table 1. Thisthickness of sheet is not being used.(3) Del

35、eted the 6 by 1in. and 150 by 25 mm corrugation fromTable 2. this is an unstable corrugation in aluminum and hasnot been fabricated for many years.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users o

36、f this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every fiv

37、e years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical c

38、ommittee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA

39、 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 4 Corrugated Sheet Lip DimensionsNominal CorrugationSizeLip DimensionMinimum Maximumin. mm in. mm in. mm223 by12 68 by 1334 191516 243 by 1 75 by 2578 22 118 28B 744/B 744M 053