ASTM B465-2009 Standard Specification for Copper-Iron Alloy Plate Sheet Strip and Rolled Bar《铜铁合金板、薄板、带材和轧制棒材的标准规范》.pdf
《ASTM B465-2009 Standard Specification for Copper-Iron Alloy Plate Sheet Strip and Rolled Bar《铜铁合金板、薄板、带材和轧制棒材的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM B465-2009 Standard Specification for Copper-Iron Alloy Plate Sheet Strip and Rolled Bar《铜铁合金板、薄板、带材和轧制棒材的标准规范》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B465 09Standard Specification forCopper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar1This standard is issued under the fixed designation B465; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision
2、. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification establishes Copper Alloy UNS N
3、os.C19200, C19210, C19400, C19500, C19700, and C19720plate, sheet, strip, and rolled bar.1.2 UnitsValues stated in inch-pound units are to beregarded as standard. The values given in parentheses aremathematical conversions to SI units, which are provided forinformation only and are not considered st
4、andard.2. Referenced Documents2.1 ASTM Standards:2B193 Test Method for Resistivity of Electrical ConductorMaterialsB248 Specification for General Requirements for WroughtCopper and Copper-Alloy Plate, Sheet, Strip, and RolledBarB601 Classification for Temper Designations for Copperand Copper AlloysW
5、rought and CastB846 Terminology for Copper and Copper AlloysE8 Test Methods for Tension Testing of Metallic Materials3E54 Test Methods for ChemicalAnalysis of Special Brassesand Bronzes4E62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Methods)E75 Test Methods for Chemic
6、al Analysis of Copper-Nickeland Copper-Nickel-Zinc AlloysE112 Test Methods for Determining Average Grain SizeE478 Test Methods for ChemicalAnalysis of CopperAlloysE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)3. General Requirements3.1 The following sections of Sp
7、ecification B248 constitutea part of this specification:3.1.1 Terminology,3.1.2 Materials and Manufacture,3.1.3 Workmanship, Finish, and Appearance,3.1.4 Sampling,3.1.5 Number of Tests and Retests,3.1.6 Specimen Preparation,3.1.7 Test Methods (except chemical analysis),3.1.8 Significance of Numerica
8、l Limits,3.1.9 Inspection,3.1.10 Rejection and Rehearing,3.1.11 Certification,3.1.12 Test Reports (Mill),3.1.13 Packaging and Package Marking, and3.1.14 Supplementary Requirements.3.2 In addition, when a section with a title identical to thatreferenced in 3.1 appears in this specification, it contai
9、nsadditional requirements which supplement those appearing inSpecification B248.4. Terminology4.1 DefinitionsFor definitions of terms related to copperand copper alloys, refer to Terminology B846.5. Ordering Information5.1 Include the following information when placing ordersfor product under this s
10、pecification:5.1.1 ASTM designation and year of issue (for exampleB465XX),5.1.2 Copper Alloy UNS No. designation (for example,C19200),5.1.3 Temper (Section 8),5.1.4 DimensionsThickness, width, length, and so forth(Section 13),5.1.5 FormPlate, sheet, strip, or rolled bar,5.1.6 How FurnishedCoils (rol
11、ls), specific lengths orstock lengths, with or without ends,1This specification is under the jurisdiction ofASTM Committee B05 on Copperand CopperAlloys and is the direct responsibility of Subcommittee B05.01 on Plate,Sheet, and Strip.Current edition approved Oct. 1, 2009. Published November 2009. O
12、riginallyapproved in 1968. Last previous edition approved in 2004 as B465 04. DOI:10.1520/B0465-09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Doc
13、ument Summary page onthe ASTM website.3Withdrawn.4Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1
14、9428-2959, United States.5.1.7 Quantitytotal weight each form, temper, and size,and5.1.8 When material is purchased for agencies of the U.S.government (Section 12).5.2 The following options are available under this specifi-cation and should be specified in the contract or purchase orderwhen required
15、:5.2.1 Type of EdgeSlit, sheared, sawed, square corners,round corners, rounded edges, or full rounded edges,5.2.2 Width and straightness tolerances (appropriate table inSpecification B248),5.2.3 Heat identification or traceability details,5.2.4 Certification, and5.2.5 Mill test report.6. Material an
16、d Manufacture6.1 Material:6.1.1 The material of manufacture shall be a cast bar, cake,or slab, of Copper Alloy UNS No. C19200, C19210, C19400,C19500, C19700, or C19720 as specified in the orderinginformation, and of such purity and soundness as to be suitablefor processing into the products prescrib
17、ed herein.6.1.2 In the event heat identification or traceability isrequired, the purchaser shall specify the details desired.NOTE 1Because of the discontinuous nature of the processing ofcastings into wrought products, it is not practical to identify a specificcasting analysis with a specific quanti
18、ty of finished product.6.2 Manufacture:6.2.1 The product shall be manufactured by such hot-working, cold-working, and annealing processes as to producea uniform wrought structure in the finished product.6.2.2 The product shall be hot- or cold-worked to thefinished size, and subsequently annealed, wh
19、en required, tomeet the temper properties specified.6.2.3 EdgesSlit edges shall be furnished unless otherwisespecified in the contract or purchase order.7. Chemical Composition7.1 The material shall conform to the requirements pre-scribed in Table 1 for the Copper Alloy UNS No. designationspecified
20、in the ordering information.7.1.1 These composition limits do not preclude the presenceof other elements. Limits may be established and analysisrequired for unnamed elements by agreement between themanufacturer and the purchaser.7.2 Copper, when specified as the remainder, may be takenas the differe
21、nce between the sum of results for specifiedelements and 100 %.7.3 When all elements listed in Table 1 for the designatedalloy are determined, the sum of results shall be 99.8 %minimum, except for C19720 which shall be 99.5 % minimum.8. Temper8.1 As defined in Classification B601, products shall bep
22、roduced in tempers O60 (soft annealed), O61 (annealed), O50(light annealed), O82 (annealed to temper -12 hard), H01 (14hard), H02 (12 hard), H03 (34 hard), H04 (hard), H06 (extrahard), HR02 (12 hard and stress relieved), HR04 (hard andstress relieved), H08 (spring), H10 (extra spring), and H14(super
23、 spring).NOTE 2The purchaser should confer with the manufacturer or sup-plier for the availability of product in a specific alloy, temper, and form,since all tempers are subject to manufacturing limitations.NOTE 3Properties of special tempers not listed in this specificationare subject to agreement
24、between the manufacturer and purchaser.9. Grain Size for Annealed Tempers9.1 Grain SizeNo grain size requirements have beenestablished for tempers O50, O60, and O61; however, theproduct material shall be fully recrystallized when examined inaccordance with Test Methods E112.10. Physical Property Req
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB4652009STANDARDSPECIFICATIONFORCOPPERIRONALLOYPLATESHEETSTRIPANDROLLEDBAR 铁合金 薄板 轧制 标准规范 PDF

链接地址:http://www.mydoc123.com/p-461299.html