ASTM B140 B140M-2012 Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod Bar and Shapes《铜锌铅杆材(铅红黄铜或硬青铜)、棒材和型材标准规格》.pdf
《ASTM B140 B140M-2012 Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod Bar and Shapes《铜锌铅杆材(铅红黄铜或硬青铜)、棒材和型材标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B140 B140M-2012 Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod Bar and Shapes《铜锌铅杆材(铅红黄铜或硬青铜)、棒材和型材标准规格》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B140/B140M 07 B140/B140M 12Standard Specification forCopper-Zinc-Lead (Red Brass or Hardware Bronze) Rod,Bar, and Shapes1This standard is issued under the fixed designation B140/B140M; the number immediately following the designation indicates the yearof original adoption or, in the cas
2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This spec
3、ification establishes the requirements for copper-zinc-lead (leaded red brass or hardware bronze) rod, bar, andshapes of UNS Copper Alloy Nos. C31400, C31600, and C32000 available for general and screw machine applications.1.2 UnitsThe values Values stated in either inch-pound units or SI units are
4、to be regarded separately as standard. Within thetext, SI units are shown in brackets. The values in each system aremay not be exact equivalents; therefore, each system shall beused independently of the other. Combining values from the two systems may result in nonconformance with the specification.
5、2. Referenced Documents2.1 ASTM Standards:2B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and ForgingsB601 Classification for Temper Designations for Copper and Copper AlloysWrought and CastB846 Terminology for Copper and Copper AlloysE8E8/E8M
6、Test Methods for Tension Testing of Metallic MaterialsE8M Test Methods for Tension Testing of Metallic Materials Metric (Withdrawn 2008)3E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)3E478 Test Methods for Chemical Analysis of Copper Alloys3
7、. General Requirements3.1 The following sections of Specification B249/B249M constitute a part of this specification:3.1.1 Terminology (B846),3.1.2 Materials and Manufacture,3.1.3 Workmanship, finish, and appearance,3.1.4 Sampling,3.1.5 Number of Tests and Retests,3.1.6 Specimen Preparation,3.1.7 Te
8、st Methods,3.1.8 Significance of Numerical Limits,3.1.9 Inspection,3.1.10 Rejection and Rehearing,3.1.11 Certification,3.1.12 Test Reports (Mill),Report,3.1.13 Product Marking,3.1.14 Packaging and Package Marking, and3.1.15 SupplementalSupplementary Requirements.3.2 In addition, when a section with
9、a title identical to one of those referenced in 3.1 appears in this specification, it containsadditional requirements thatwhich supplement those which appear appearing in Specification B249/B249M.4. Ordering Information4.1 Include the following information specified choices when placing orders for p
10、roducts under this specification:specification,as applicable:4.1.1 ASTM designation and year of issue,*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.2 Copper Alloy
11、UNS No. designation (Scope),4.1.3 Temper designation (Temper Section),4.1.4 Dimensionsdiameter, distance between parallel surfaces,4.1.5 How furnished; length, specific or stock, with or without ends,4.1.6 Quantity; total weight or length, or number of pieces of each temper, form, and alloy.alloy, a
12、nd4.1.5 Dimensionsdiameter, distance between parallel surfaces,4.1.6 How furnished; specific lengths with or without ends, and4.1.7 If product is purchased for agencies of the U.S. government. (Intended application, general use or automatic screwmachine use (Straightness Tolerance).B249/B249M).4.2 T
13、he following options are available to this specification and should be specified in the contract or purchase but may not beincluded unless specified at the time of placing of the order when required:4.2.1 Heat identificationCertification (Specification B249/B249Mor traceability details,),4.2.2 Certi
14、fication Mill Test Reports (Specification B249/B249M), and4.2.3 Mill Test Reports (Specification If product is purchased for agencies of the U.S. Government (B249/B249M).5. Material and Manufacture5.1 Material:5.1.1 The material of manufacture shall be a form (cast billets, logs, or rods) of Copper
15、Alloy UNS Nos. C31400, C31600, orC32000 of such purity and soundness as to be suitable for processing into the products prescribed herein.5.2 Manufacture:5.2.1 The product shall be manufactured by such hot working, cold working, straightening, and annealing processes as toproduce a uniform wrought s
16、tructure in the finished product.6. Chemical Composition6.1 The material shall conform to the chemical composition requirements in Table 1 for the Copper Alloy UNS No. designationspecified in the ordering information.6.1.1 These composition limits do not preclude the presence of other elements. By a
17、greement between the manufacturer and thepurchaser, limits may be established and analysis required for unnamed elements.6.2 For alloys in which zinc is listed as the “remainder,” either copper or zinc may be taken as the difference between the sumof results of all other elements determined and 100
18、%. When copper is so determined, that difference value shall conform to therequirements given in Table 1.6.3 When all elements in Table 1 are determined, the sum of the results shall be 99.6 % minimum.7. Temper7.1 Tempers, The standard tempers, as defined in Classification B601, available to for pro
19、ducts described in this specificationare O60 (soft anneal), H02 (half-hard), and H04 (hard).8. Mechanical Property Requirements8.1 Tensile Strength Requirements:1 This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcom
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB140B140M2012STANDARDSPECIFICATIONFORCOPPERZINCLEADREDBRASSORHARDWAREBRONZERODBARANDSHAPES 铜锌铅杆材铅红

链接地址:http://www.mydoc123.com/p-460444.html