ASTM A491-2007 Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric《镀铝钢链环栏栅结构的标准规范》.pdf

《ASTM A491-2007 Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric《镀铝钢链环栏栅结构的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM A491-2007 Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric《镀铝钢链环栏栅结构的标准规范》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 491 07Standard Specification forAluminum-Coated Steel Chain-Link Fence Fabric1This standard is issued under the fixed designation A 491; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A nu

2、mber in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers aluminum-coated steel chain-link fence fabric, aluminum-coated before weaving.1.2 The values stated in inch-po

3、und units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:2A 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 700 Practices for Packaging, Marking, and LoadingMethods for Steel Products for

4、ShipmentA 817 Specification for Metallic-Coated Steel Wire forChain-Link Fence Fabric and Marcelled Tension Wire2.2 Federal Standard:3Fed. Std. No. 123 Marking for Shipment, Civil Agencies2.3 Military Standards:3MIL-STD-129 Marking for Shipment and StorageMIL-STD-163 Steel Mill Products, Preparation

5、 for Ship-ment and Storage3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 chain link fence fabrica fencing material made fromsteel wire helically wound and interwoven in such a manner asto provide a continuous mesh without knots or ties except inthe form of knuckling or of twi

6、sting the ends of the wires toform the selvage of the fabric.3.1.2 diamond countthe number of diamond openingsfrom one edge of the fabric to the other. The diamond count ofa given fabric shall begin at the first completed diamond at oneedge and continue to the unfinished (12) or full opening at theo

7、ther edge.3.1.3 knucklinga term used to describe the type of selvageobtained by interlocking adjacent pairs of wire ends and thenbending the wire ends back into a loop. The loop shall beclosed or nearly closed to a measurement less than the diameterof the wire.3.1.4 twistinga term used to describe t

8、he type of selvageobtained by twisting adjacent pairs of wire ends together in aclose helix of 112 machine turns, which is equivalent to 3 fulltwists, and cutting the wire ends at an angle. The wire endsbeyond the twist shall be at least14 in. 6.4 mm long. Thistype of selvage is not used on fabric w

9、ith a mesh size of lessthan 2 in. 50.8 mm.4. Ordering Information4.1 Orders for chain-link fence fabric purchased to thisspecification shall include the following information:4.1.1 Quantity (Section 14),4.1.2 Size of mesh (Section 7),4.1.3 Size of wire (Section 8),4.1.4 Height of fabric (Section 9),

10、4.1.5 Diamond count, if specified (Section 6),4.1.6 Type of selvage (Section 10),4.1.7 Certification if required (Section 17), and4.1.8 ASTM designation and year of issue.4.2 All rolls of fencing accepted by the purchaser shall bebilled on the basis of the original footage of the rolls beforesamplin

11、g, unless changed by contractual arrangement.NOTE 1A typical ordering description is as follows: 25 rolls, 50 fteach, chain-link fence fabric, aluminum-coated, 2 in. mesh. 0.148 in. wire,60 in. high, knuckled both selvages, to ASTM A 491XX.1This specification is under the jurisdiction of ASTM Commit

12、tee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved Sept. 15, 2007. Published October 2007. Originallyapproved in 1963. Last previous edition approved in 2003 as A 491 - 03.2For referenced ASTM standards, visit the

13、 ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia

14、, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Materials5.1 The wire from which the fabric is woven shall conformto all requirements of Specification A 817 for Type I coating.6. Weave6.1 The wire shal

15、l be woven throughout in the form ofapproximately uniform square mesh, having parallel sides andhorizontal and vertical diagonals of approximately uniformdimensions. The top and bottom of the fabric shall be knuckledor twisted as specified in Section 10.6.2 Typical diamond count for each standard he

16、ight isshown in Table 1. Other diamond counts are permissibleprovided that they are consistent within a lot. The purchaserhas the option to specify the diamond count (4.1.5).7. Size of Mesh7.1 The size of mesh shall be as indicated in Table 2 (seeFig. 1).7.2 The permissible variation from the specif

17、ied size ofmesh shall be 618 in. 63.2 mm for all mesh sizes over 1 in.25 mm, and 6116 in. 61.6 mm for all mesh sizes 1 in.25.4 mm and under.7.3 The size of mesh shall be determined by measuring theminimum clear distance between the wires forming the parallelsides of the mesh, and determined as the a

18、verage of tworeadings taken at right angles to each other.8. Size of Wire8.1 Chain-link fabric shall be fabricated from wire diam-eters as listed in Specification A 817, with a permissiblevariation from the specified diameter of the coated wire of60.005 in. 60.13 mm.9. Height of Fabric9.1 Chain-link

19、 fabric shall be furnished in the standardheights shown in Table 2. Custom order fabric is available inheights to and including 20 ft. 6.56 m. The height of fabricshall be the overall dimension from ends of twists or knuckles.The permissible variation from the specified height shall be 61in. 625 mm

20、for standard selvage on fabric with mesh sizes 1in. 25 mm and over and 612 in. 613 mm for all fabric withmesh sizes less than 1 in. 25 mm.10. Selvage10.1 Unless otherwise specified by the purchaser, fabricswith 2- or 218-in. 50- or 54-mm mesh, in heights 60 in. 1520mm and under shall be knuckled at

21、both selvages. Fabric 72in. 1830 mm high and over shall be knuckled at one selvageand twisted at the other.10.2 The selvages of fabrics with meshes of less than 2 in.50 mm shall be knuckled.NOTE 2Caution: Twisted selvages for fence fabric under 72 in. 1830mm in height are not recommended because of

22、consumer safety consid-erations.11. Weight of Aluminum Coating11.1 The weight of aluminum coating on the wire in thefabric shall be as specified in Specification A 817, for the wirediameter used (see Table 3).12. Breaking Strength12.1 Wire constituting the fabric shall meet the minimumbreaking stren

23、gth listed in the Breaking Strength Table ofSpecification A 817 (see Table 4) when tested in accordancewith Test Methods and Definitions A 370. Specimens used toestablish conformance with this requirement shall consist ofindividual pickets from a section of the fence fabric. Thespecimen shall be of

24、sufficient length so as to be firmly grippedin the testing machine after straightening. The actual gagelength (distance between jaws) of the specimen shall be limitedto the undeformed length of wire between two adjacentstraightened bends.13. Workmanship, Finish, and Appearance13.1 Chain-link fence f

25、abric shall be produced by methodsrecognized as good commercial practices.13.2 Excessive roughness, blisters, and flaking shall benoted. These and other defects, if present to any considerableextent, shall provide a basis for rejection.NOTE 3Rust formations on the cut ends of the wire at the fabrics

26、elvages are inherent characteristics of this material and do not warrantrejection of the fabric.14. Standard Length of Rolls14.1 The standard length of roll shall be 50 ft 15.24 m 61 % except as otherwise agreed upon at the time of purchase.TABLE 1 Typical Diamond CountANOTE 1Other diamond counts ar

27、e permitted (see 6.2).NOTE 2 For fabric heights over 144 in., see Section 9.Nominal Diameter CoatedWire, in.Size ofMesh, in.Height of Fence Fabric, in.36 42 48 60 72 84 96 108 120 1440.192 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.1

28、48 1 20 23 27 33 39 45 53 61 67 790.148 114 . . . . . . 23 29 35 41 46 52 56 700.135 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.120 2 1012 1212 1412 1712 2012 2412 . . . .0.120 134 . . . . . . 3112 3512 3912 47120.120 114 . . . . . . 23 29 35 41 46 52 58 700.120 1 20 23 27 33 39 45 53 61 6

29、7 790.113 218 912 1112 1312 1612 1912 . . . . .ASee Appendix X1 for metric equivalents.A49107214.2 The length of roll shall be determined by unrolling aroll of fabric on a flat surface and exerting tension byappropriate means to remove all slack. The tension appliedshall not reduce the actual height

30、 of the fabric by more than116in./ft 5.3 mm/m of height or by more than12 in. 12.7 mm,whichever is less.15. Sampling and Number of Tests15.1 One roll from every 50 rolls or fraction thereof in a lotshall be taken at random as a sample for test purposes. In nocase shall less than two samples be teste

31、d except when the lotis less than 10 rolls only one roll shall be selected for thesample.15.2 Sample rolls selected shall be inspected for weave(Section 6), size of mesh (Section 7), diamond count (6.2), wiresize (Section 8), height of fabric (Section 9), selvage (Section10) and length (Section 14).

32、15.3 If any specimen tested fails to meet the requirements ofthis specification, the roll represented by the specimen shall berejected and two additional rolls shall be inspected, both ofTABLE 2 Sizes of Wire and MeshANOTE For fabric heights over 144 in., see 9.1.Specified Diameter ofCoated Wire, in

33、.Size, Coated Wire Gage Size of Mesh, in.BHeight of Fence Fabric, in.0.192 6 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148C9114 ., ., 48, 60, 72, 84, 96, 108, 120, 1440.148 9 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.135 10 2 36, 42, 48, 60, 7

34、2, 84, 96, 108, 120, 1440.120 11 2 36,42,48,60,72,840.120 11 134 96,108, 120, 1440.120C11 114 ., ., 48, 60, 72, 84, 96, 108, 120, 1440.120 11 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 1158D36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 1112D36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 1138D

35、36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.113 1112 218 36,42,48,60,72ASee Appendix X1 for metric equivalents.BSee Fig. 1 for mesh dimensions for58 in.,12 in., and38 in. fence fabric.CThis mesh size and smaller is recommended for swimming pools.DThese sizes are designed for security purposes.Selvage

36、, S Height, H, in. Width, W, in.38 in. mesh343412 in. mesh1516151658 in. mesh 118 118FIG. 1 Mesh Dimensions for38 in.,12 in., and58 in. FenceFabricTABLE 3 Minimum Weight of Aluminum Coating for Type ISpecified Diameter ofCoated Wire, in. mmMinimum Weight of Coating,oz/ft2g/m2 of uncoated wire surfac

37、e0.192 4.88 0.40 1220.148 3.76 0.40 1220.135 3.43 0.40 1220.120 3.05 0.35 1070.113 2.87 0.30 92TABLE 4 Breaking StrengthSpecified Diameter of CoatedWire, in. mmBreaking Strength, min,lbf N0.192 4.88 2170 96500.148 3.76 1290 57400.135 3.43 1290 57400.120 3.05 850 37800.113 2.87 750 3340A491073which s

38、hall meet the requirements in every respect; otherwise,the lot represented by the samples may be rejected.16. Inspection16.1 Unless otherwise specified in the purchase order orcontract, the manufacturer is responsible for the performanceof all inspection and test requirements specified in this speci

39、-fication. Except as otherwise specified in the purchase order orcontract, the manufacturer may use his own or any othersuitable facilities for the performance of the inspection and testrequirements unless disapproved by the purchaser at the timethe order is placed. The purchaser shall have the righ

40、t toperform any of the inspection and tests set forth in thisspecification when such inspections and tests are deemednecessary to assure that the material conforms to prescribedrequirements.17. Certification17.1 When specified in the purchase order or contract, aproducers or suppliers certification

41、shall be furnished to thepurchaser that the material was manufactured, sampled, tested,and inspected in accordance with this specification and hasbeen found to meet the requirements. When specified in thepurchase order or contract, a report of the test results shall befurnished.18. Packaging, Markin

42、g, and Loading18.1 Each length of chain-link fence fabric shall be tightlyrolled and firmly tied. Each roll shall carry a tag showing thetype of coating, the specified wire size, mesh size, the specifiedlength and height of fabric in the roll, ASTM DesignationA 491, and the name or mark of the manuf

43、acturer.18.2 Unless otherwise specified, packaging, marking andloading for shipment shall be in accordance with PracticesA 700.18.3 When specified in the contract or order, and for directprocurement by or direct shipment to the U.S. government,when Level A is specified, preservation, packaging, and

44、pack-ing shall be in accordance with Level A requirements ofMIL-STD-163.18.4 When specified in the contract or order, and for directprocurement by or direct shipment to the U.S. government,marking for shipment, in addition to the requirements specifiedin the contract or order, shall be in accordance

45、 with MIL-STD-129 for U.S. military agencies and in accordance with Fed. Std.No. 123 for civil agencies.19. Keywords19.1 aluminum coated (aluminized) iron and steel articles;aluminum coated (aluminized) steel chain link fence fabric;chain link fence; steel; coatings; aluminum (aluminized);fence/fenc

46、ing materials; chain linkAPPENDIX(Nonmandatory Information)X1. Approximate Metric Equivalents for Table 1 and Table 2TABLE X1.1 Approximate Metric Equivalents for Table 1 andTable 2Sizes of Wire and Mesh Height of Fence Fabricin. mm in. mm0.192 4.88 36 9100.148 3.76 42 10700.135 3.43 48 12200.120 3.

47、05 60 15200.113 2.87 72 18301 25 84 2130114 32 . .134 44 96 24402 50 108 27402! 54 120 3050144 3660A491074ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised tha

48、t determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reappro

49、ved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committe