ASTM A1001-2001(2006) Standard Specification for High Strength Steel Castings in Heavy Sections《重型型钢中高强度钢铸件的标准规范》.pdf

《ASTM A1001-2001(2006) Standard Specification for High Strength Steel Castings in Heavy Sections《重型型钢中高强度钢铸件的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM A1001-2001(2006) Standard Specification for High Strength Steel Castings in Heavy Sections《重型型钢中高强度钢铸件的标准规范》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 1001 01 (Reapproved 2006)Standard Specification forHigh Strength Steel Castings in Heavy Sections1This standard is issued under the fixed designation A 1001; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year o

2、f last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers cast alloy steels in the normal-ized and tempered or quenched and tempered condition, ins

3、ection sizes through 37 in. (940 mm), suitable for high straingradient conditions such as those encountered in hooks, shack-les, support frames, and other lifting devices. The classes ofsteel in this specification are weldable only with qualifiedprocedures.1.2 Section range and class selection will

4、depend on designand service conditions. Users should note that this specificationcontemplates mechanical property gradients.1.3 The values stated in inch-pound units or SI units are tobe regarded separately as standard. Within the text, the SI unitsare shown in brackets. The values stated in each sy

5、stem are notexact equivalents; therefore, each system must be used inde-pendently of the other. Combining values from the two systemsmay result in non-conformities with the specification. Inch-pound units are applicable for material ordered to this Speci-fication and SI units for material ordered to

6、 this Specification.1.4 If, by agreement, castings are to be supplied in apartially completed condition, that is, all of the provisions ofthe product specification have not been filled, then the materialmarking (see Section 15) and certification (see Section 14) areto reflect the extent to which the

7、 product specification require-ments have been met.2. Referenced Documents2.1 ASTM Standards:A 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 609/A 609M Practice for Castings, Carbon, Low-Alloy,and Martensitic Stainless Steel, Ultrasonic ExaminationThereofA 703/A 703M Spec

8、ification for Steel Castings, GeneralRequirements, for Pressure-Containing PartsE94 Guide for Radiographic ExaminationE 165 Test Method for Liquid Penetrant ExaminationE 709 Guide for Magnetic Particle ExaminationE 1019 Test Methods for Determination of Carbon, Sulfur,Nitrogen, and Oxygen in Steel a

9、nd in Iron, Nickel, andCobalt AlloysE 1447 Test Method for Determination of Hydrogen inTitanium and Titanium Alloys by the Inert Gas FusionThermal Conductivity/Infrared Detection MethodE 1806 Practice for Sampling Steel and Iron for Determi-nation of Chemical Composition2.2 Manufacturers Standardiza

10、tion of the Value and Fit-tings Industry Standards:MSS SP-55 Quality Standard for Steel Castings VisualMethod23. General Conditions for Delivery3.1 Materials furnished to this Specification shall conformto the applicable requirements of SpecificationA 703/A 703M,including the supplementary requireme

11、nts that are indicated onthe purchase order.3.2 Terminology and test methods shall be in accordancewith Test Methods and Definitions A 370.3.3 In the case of conflict between requirements of thisspecification and referenced specifications, the former shallprevail.4. Ordering Information4.1 It shall

12、be the responsibility of the purchaser to specifyall requirements that are necessary for material ordered underthis specification. Such requirements to be considered include,but are not limited to, the following:4.1.1 A description of the casting by pattern number or afully dimensional and tolerance

13、d drawing,4.1.2 ASTM designation and year of issue,4.1.3 Section range and class of steel (see Table 1),4.1.4 Definition of inspection methods, extent of examina-tion, frequency, casting quality zones, and acceptance criteria(see Section 11).4.1.5 Product marking locations (see Section 15),4.1.6 Cer

14、tification report options (see Section 14),4.1.7 Options in the specification (see 1.4 and 11.6), and1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel, and Related Alloys and is the direct responsibility of SubcommitteeA01.18 on Castings.Current edition app

15、roved March 1, 2006. Published March 2006. Originallyapproved in 1999. Last previous edition approved in 2001 as A 1001 - 01.2Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602.1Copyright ASTM International, 100 Barr

16、Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.1.8 The supplementary requirements desired.5. Test Block Requirements5.1 The supplier shall produce a minimum of one test blockfor each heat.5.2 Test block configuration shall be in accordance with Fig.1.Astandard draft ang

17、le is permitted over the length “L” of thetest block provided the minimum cylinder diameter is greaterthan “T” given in Table 2.5.3 Test block size shall be in accordance with Table 2 forspecified section range. The section range selection made bythe purchaser (see 4.1.3) should consider casting sec

18、tion sizeand geometry, service conditions, mechanical property corre-lations developed by the supplier, or other important factors.5.4 Tension and Charpy impact tests shall be performed onspecimens taken from both the 1/8T and 3/8T locations andshall be oriented within the 8-in. (203-mm) midsection

19、asshown in Fig. 1.5.5 Oxygen and nitrogen gas content tests shall be per-formed on specimens taken from the 3/8T location and shall bewithin the 8 in. (203 mm) midsection as shown in Fig. 1.6. Materials and Manufacture6.1 The steel shall be made by electric furnace process withmethods to conform to

20、the maximum gas levels given in Table3. These methods may include a special refining process suchas argon-oxygen-decarburization (AOD).6.2 Heat treatment procedure shall be reported to the pur-chaser by the supplier for the specified section range, class, andgrade.TABLE 1 Required Mechanical Propert

21、iesChemistryGradeATensile Strengthksi (MPa)Yield Strength, min ksi(MPa) at 0.2 % OffsetElongation, 2 in (50mm) or 4d, min, %Reduction of Area,min %Charpy V-Notch, MinAverage, ft-lb (J)SectionRangeClass T/8B3T/8BT/8B3T/8BT/8B3T/8BT/8B3T/8BT/8B3T/8B1 A I, II 110 (760) 100 (690) 90 (620) 80 (550) 18 15

22、 36 30 25 (34) 15 (20)1 B I 105 (725) 95 (655) 85 (585) 76 (525) 15 11 30 22 25 (34) 15 (20)1 C I 90 (620) 80 (550) 70 (485) 63 (435) 17 13 34 26 25 (34) 15 (20)2 A I 110 (760) 100 (690) 90 (620) 80 (550) 18 15 36 30 25 (34) 15 (20)2 B I 105 (725) 95 (655) 85 (585) 76 (525) 16 12 32 24 25 (34) 15 (2

23、0)2 C I 90 (620) 80 (550) 70 (485) 63 (435) 18 14 36 28 25 (34) 15 (20)3 A I, III 110 (760) 100 (690) 90 (620) 80 (550) 18 15 36 30 25 (34) 15 (20)3 B I 105 (725) 95 (655) 85 (585) 76 (525) 17 13 34 26 25 (34) 15 (20)3 C I 90 (620) 80 (550) 70 (485) 63 (435) 19 16 38 32 25 (34) 15 (20)4 A I, II 110

24、(760) 100 (690) 90 (620) 80 (550) 18 15 36 30 25 (34) 15 (20)4 B I 105 (725) 95 (655) 85 (585) 76 (525) 19 16 38 32 25 (34) 15 (20)4 C I 90 (620) 80 (550) 70 (485) 63 (435) 21 18 42 36 25 (34) 15 (20)5 A I, II 110 (760) 100 (690) 90 (620) 80 (550) 18 15 36 30 25 (34) 15 (20)5 B I 105 (725) 95 (655)

25、85 (585) 76 (525) 19 16 38 32 25 (34) 15 (20)5 C I 90 (620) 80 (550) 70 (485) 63 (435) 21 18 42 36 25 (34) 15 (20)6 A I 110 (760) 100 (690) 90 (620) 80 (550) 18 15 36 30 25 (34) 15 (20)6 B I 105 (725) 95 (655) 85 (585) 76 (525) 19 16 38 32 25 (34) 15 (20)6 C I 90 (620) 80 (550) 70 (485) 63 (435) 21

26、18 42 36 25 (34) 15 (20)7 A I 110 (760) 100 (690) 90 (620) 80 (550) 18 15 36 30 25 (34) 15 (20)7 B I 105 (725) 95 (655) 85 (585) 76 (525) 19 16 38 32 25 (34) 15 (20)7 C I 90 (620) 80 (550) 70 (485) 63 (435) 21 18 42 36 25 (34) 15 (20)ASee 7.1. Chemistry other than these listed can be used if propert

27、ies are met.BSee Fig. 1FIG. 1 Test Block ConfigurationTABLE 2 Section Range Definition and Test Block DimensionsSectionRangeSection Size, in (mm) Test Block Dimensions, in (mm)AOver Not Over T L1 3 (76) 5 (127) 4 (102) 8 (203)2 5 (127) 7 (178) 6 (152) 8 (203)3 7 (178) 11 (279) 9 (229) 9 (229)4 11 (2

28、79) 15 (381) 13 (330) 13 (330)5 15 (381) 21 (533) 18 (457) 18 (457)6 21 (533) 29 (737) 25 (635) 25 (635)7 29 (737) 37 (940) 33 (813) 33 (813)ASee Fig. 1.TABLE 3 Maximum Gas Content LevelsSectionRangeNitrogen,ppmOxygen,ppmOxygenAnalysisTolerance, ppmOxygenAnalysisLimit, ppmA1 110 100 30 1302 110 100

29、30 1303 100 90 27 1174 100 90 27 1175 90 80 24 10468 7 1 9177060 8 78ASpecification compliance level is average value of three determinations, see10.3A 1001 01 (2006)26.2.1 Multiple austenitizing is permitted.6.2.2 Multiple tempering is permitted. The minimum finaltempering temperature shall not be

30、less than 1100F (593C).Post weld heat treatment shall not be less than 1050F (566C).6.3 Test block(s) may be heat treated separately from thecastings they represent.6.3.1 Test block(s) shall be heat treated in the same produc-tion heat treat equipment, in the same facility, and to the sameprocedure

31、as the castings to be produced. Test block(s) areexcluded from post weld heat treatment (see 12.2.9).6.3.2 The test block(s) tempering temperature shall bewithin 6 25F (14C) of the casting tempering temperature.6.4 Heat treatment charts showing time and temperatureshall be prepared and held availabl

32、e for inspection by thepurchaser.7. Chemical Composition7.1 Supplier shall select the casting chemistry Grade fromTable 1 for the section range, and class specified by thepurchaser.7.1.1 Chemical composition shall conform to Table 4 forGrades II and III.7.1.2 Grade I designates the use of an alterna

33、te chemistryselected by the supplier.Alternate chemistries shall conform tothe allowable element ranges and limits given in Table 5.7.2 A product analysis shall be made for specificationconformance. The product analysis shall be performed on aspecimen taken from the test block(s) in Section 5 and sh

34、all befrom the 3/8T location and shall be within the 8 in. (203 mm)midsection as shown in Fig. 1. The supplier shall perform theproduct analysis in addition to any other process controlanalysis.7.3 Retests for conformance are permitted in accordancewith Section 13.8. Tension Test8.1 Tension tests sh

35、all be performed on test specimens takenfrom test block(s) as determined in Section 5.8.1.1 One tension test specimen is required at each of the1/8T and 3/8T locations and shall be oriented within the 8 in.(203 mm) midsection as shown in Fig. 1.8.1.2 Tension test specimens shall be machined to the f

36、ormand dimension shown in Fig. 4 of Test Methods and DefinitionsA 370 and tested in accordance with those test methods.8.2 Mechanical properties shall conform to the requirementsgiven in Table 1.8.3 Retests for conformance are permitted in accordancewith Section 13.9. Charpy Impact Test9.1 Charpy im

37、pact tests shall be performed on test speci-mens taken from test block(s) as determined in Section 5. Oneset of Charpy impact test specimens is required at each of the1/8T and 3/8T locations and shall be oriented within the 8 in.(203 mm) midsection as shown in Fig. 1.9.2 Charpy impact tests shall be

38、 performed in accordancewith A 703/A 703M S8.1 at 40F (40C) temperature.9.3 Acceptance criteria shall be in accordance with A 703/A 703M S8.2 method and conform to the average absorbedenergy values given in Table 1.9.4 Minimum single specimen value shall not be less than 5ftlbs (7 J) below the avera

39、ge absorbed energy values given inTable 1.9.5 Retests for conformance are permitted in accordancewith Section 13.10. Gas Content Requirements10.1 Oxygen and nitrogen gas content tests shall be per-formed on test specimens taken from the test block(s) asdetermined in Section 5. Gas content tests shal

40、l be performedon specimens taken from the 3/8T location and shall be withinthe 8 in. (203 mm) midsection as shown in Fig. 1.10.2 Hydrogen gas content tests shall be performed on ladlespecimens for section ranges 4-7 and results reported.Acarriergas infusion method may be used with samplers and instr

41、u-mentation in accordance with Practice E 1806 and Test MethodE 1447 respectively.TABLE 4 Chemical Grade Composition (Maximum PercentUnless Range is Given)GradeI II IIIElement: See Table 5 .to .toCarbon . . . 0.20 to 0.28 0.20 to 0.28Manganese . . . 1.00 to 1.40 1.00 to 1.40Phosphorus . . . 0.02 0.0

42、3Sulfur . . . 0.015 0.025Silicon . . . 0.30 to 0.60 0.30 to 0.60Nickel . . . 1.00 to 1.30 1.00 to 1.30Chromium . . . 0.80 to 1.20 0.80 to 1.20Molybdenum . . . 0.60 to 0.85 0.60 to 0.85Aluminum . . . 0.03 0.07Residual Elements: See Table 5Zirconium . . .AACopper . . .Titanium . . .Tungsten . . .AAVan

43、adium . . .Columbium . . .Boron . . .AATotal Content ofResidual Elements. . . 0.60 0.60AReported for Information OnlyTABLE 5 Element Tolerance Ranges and Maximum Limits forAlternate ChemistriesElement Average ofDeclared Range,(%)Maximum Range(%)Maximum Limit(%)Carbon All 0.08 0.35Manganese 1.00$1.00

44、0.300.40.Phosphorus All . . . 0.02Sulfur All . . . 0.015Nickel 1.50$1.500.300.50.Chromium 1.50$1.500.400.50.Molybdenum All 0.25 . . .Aluminum All 0.04 0.06Vanadium All 0.10 . . .CopperA. . .TitaniumA. . .ColumbiumA. . .ZirconiumA. . .NitrogenA. . .AReported for information only.A 1001 01 (2006)310.3

45、 Oxygen and nitrogen gas content tests shall be per-formed in accordance with Test Methods E 1019. Oxygencontent for specification compliance shall be taken as theaverage value of three determinations.10.4 Oxygen and nitrogen gas content requirements of steelused for the castings shall conform to th

46、e requirements given inTable 3.10.5 Retests for conformance are permitted in accordancewith Section 13.11. Quality11.1 The purchaser shall establish casting quality zones thatinclude, at a minimum, a shell and a core depth zone (See Fig.2).11.2 Non-destructive examination for specification con-forma

47、nce shall be of the final heat treated condition.11.3 Casting shell zone surface shall be visually examinedand graded in accordance with MSS SP-55.Acceptance criteriashall be as specified in the purchase order.11.4 Casting shell zone surface shall be examined fordiscontinuities by magnetic particle

48、or liquid penetrant inspec-tion, or both, in accordance with Practice E 709 and TestMethod E 165 respectively. Personnel performing the exami-nation shall have at least ASNT Level II qualification in theinspection method used and shall be qualified by personshavingASNT Level III qualification. Inspe

49、ction method, extentof examination, frequency, and acceptance criteria shall be asspecified in the purchase order.11.5 Casting shell and core zones shall be examined forinternal defects by ultrasonic or radiographic inspection, orboth, in accordance with Practice A 609/A 609 M and GuideE94respectively. Personnel performing the examination shallhave at least ASNT Level II qualification in the inspectionmethod used and shall be qualified by persons having ASNTLevel III qualification. Inspection method, extent of examina-tion, frequency, and acceptance criteria for each zo