ASME B16 24-2016 Cast Copper Alloy Pipe Flanges Flanged Fittings and Valves Classes 150 300 600 900 1500 and 2500《铸铜合金管法兰 法兰配件和阀门 等级为150 300 600 900 1500和2500》.pdf

《ASME B16 24-2016 Cast Copper Alloy Pipe Flanges Flanged Fittings and Valves Classes 150 300 600 900 1500 and 2500《铸铜合金管法兰 法兰配件和阀门 等级为150 300 600 900 1500和2500》.pdf》由会员分享，可在线阅读，更多相关《ASME B16 24-2016 Cast Copper Alloy Pipe Flanges Flanged Fittings and Valves Classes 150 300 600 900 1500 and 2500《铸铜合金管法兰 法兰配件和阀门 等级为150 300 600 900 1500和2500》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、AN AMERICAN NATIONAL STANDARD ASME B16.24-2016(Revision of ASME B16.24-2011)Cast Copper Alloy Pipe Flanges, Flanged Fittings, and ValvesClasses 150, 300, 600, 900, 1500, and 2500ASME B16.24-2016(Revision of ASME B16.24-2011)Cast Copper Alloy PipeFlanges, FlangedFittings, and ValvesClasses 150, 300,

2、600, 900,1500, and 2500AN AMERICAN NATIONAL STANDARDTwo Park Avenue New York, NY 10016 USADate of Issuance: October 31, 2016The next edition of this Standard is scheduled for publication in 2021.ASME issues written replies to inquiries concerning interpretations of technical aspects of thisStandard.

3、 Periodically certain actions of the ASME B16 Committee may be published as Cases.Cases and interpretations are published on the ASME Web site under the Committee Pages athttp:/cstools.asme.org as they are issued.Errata to codes and standards may be posted on the ASME Web site under the Committee Pa

4、ges toprovide corrections to incorrectly published items, or to correct typographical or grammatical errorsin codes and standards. Such errata shall be used on the date posted.The Committee Pages can be found at http:/cstools.asme.org/. There is an option available toautomatically receive an e-mail

5、notification when errata are posted to a particular code or standard.This option can be found on the appropriate Committee Page after selecting “Errata” in the “PublicationInformation” section.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was

6、developed under procedures accredited as meeting the criteria for American NationalStandards. The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate. The proposed code or standard

7、 was madeavailable for public review and comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.ASME does not take any

8、position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent, nor assumes any such liability. Users of a code

9、 or standard are expresslyadvised that determination of the validity of any such patent rights, and the risk of infringement of such rights, isentirely their own responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted asgovernme

10、nt or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies, which precludes the issuance of interpretations by individuals.No part of this document may be reprod

11、uced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersTwo Park Avenue, New York, NY 10016-5990Copyright 2016 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.C

12、ONTENTSForeword ivCommittee Roster . viCorrespondence With the B16 Committee viiSummary of Changes ixList of Changes in Record Number Order xi1 Scope . 12 General . 13 PressureTemperature Ratings 24 Size and Method of Designating Openings 85 Marking . 86 Materials 107 Flange and Valve Body Dimension

13、s . 118 Fitting and Valve Dimensions . 119 Bolting and Gaskets . 1210 Tolerances. 1211 Pressure Testing . 13Figure1 Method of Designating Outlets of Reducing Fittings . 9Tables1 PressureTemperature Ratings for ASTM B61 Alloy C92200 and ASTM B62 AlloyC83600 . 32 Dimensions of Class 150 Threaded Compa

14、nion and Blind Flanges for Alloys C83600and C92200 43 Dimensions of Class 150 Elbows, Tees, Crosses, Laterals, True Ys (Straight Sizes),and Reducers 54 Dimensions of Class 300 Threaded Companion and Blind Flanges for Alloys C83600and C92200 65 Dimensions of Class 300 Elbows, Tees, Crosses, Laterals,

15、 True Ys (Straight Sizes),and Reducers 76 PressureTemperature Ratings for ASTM B148 Alloy C95200 Flanges . 87 PressureTemperature Ratings for ASTM B148 Alloy C95400 Flanges . 8Mandatory AppendicesI Dimensions of Fittings in U.S. Customary Units . 15II ASTM B148 Valve Construction Supplemental Requir

16、ements . 21III References 24Nonmandatory AppendicesA Quality System Program 25B Method Used for Establishing PressureTemperature Ratings 26iiiFOREWORDThe development of the first Bronze Flanged Standard began in 1910 to eliminate the confusionprevailing in the trade with respect to bronze flange dim

17、ensions and service ratings. The workculminated and was published in 1914 under the title “1914 Brass Standard Flange Dimensions”for 150-lb and 250-lb (now Class 150 and Class 250) steam pressures.This was superseded in 1928 by the Manufacturers Standardization Society of Valves andFittings Industry

18、 (MSS) “Standard Practice” SP-2, which contained changes to provide inter-changeability with the American Cast-Iron Flange Standards for 125-lb (now Class 125) andClass 250 stream pressures. Subsequent revisions were issued in 1930 and 1936. In the latter, anew column of thickness for 300-lb (now Cl

19、ass 300) flanges was added.In the 1937 edition, illustrations and dimensions of bronze-flanged fittings were added. Thiswas edited and reprinted in 1943 to conform to the U.S. Department of Commerce, NationalBureau of Standards, Simplified Practice Recommendation R-183-42, and to the War ProductionB

20、oard Limitation Order L-252, dated January 23, 1943.In the 1946 edition, the pressuretemperature ratings were added for the Class 150 and Class 300standards and the dimensions for that reference to the Class 250 standard were omitted. LimitationOrder L-252 was canceled on April 28, 1945. The period

21、of government prohibition of manufactureand civilian use of the Class 250 standard (during the life of Order L-252) caused no hardshipon the part of either the manufacturer or the consumer, indicating that this pressure class inbronze products did not warrant being recognized as a standard.This Stan

22、dard was reviewed and reaffirmed in 1949. In October 1951, MSS ceded it to SectionalCommittee B16 on Pipe Flanges and Flanged Fittings for review and possible approval as anAmerican Standard.Following approval of the sectional committee and sponsor organizations, it was sent to theAmerican Standards

23、 Association (ASA), now the American National Standards Institute (ANSI),for approval and designation as an American Standard. This was granted on February 27, 1953.In 1961, following the organization of Subcommittee No. 11 (now Subcommittee J), the 1953edition was revised. Chief among the changes r

24、ecommended was the deletion of reference tobrass. This resulted from an action of ASTM redefining the alloys that could properly be calledbronze. Several other changes that brought the Standard up to date were also approved by theB16 Committee, with approval designation as an American Standard being

25、 granted onJuly 20, 1962.Subcommittee J, in keeping with regulations of ANSI, reviewed the Standard in 1969. Onlyminor changes were made. Among these were the presentation of pressuretemperature ratingsin tabular form, and the gasket-retaining grooves being made permissible rather than recom-mended.

26、 Final approval of the changes was granted by ANSI on January 27, 1971.A revision was undertaken in 1977, and several changes were proposed. Foremost among thesewas the addition of metric equivalents and the elimination of the optional gasket-retaininggrooves. In addition, the Standard was extensive

27、ly revised editorially. Following approvals bySubcommittee J and the Standards Committee, ANSI granted its approval on June 26, 1979.In 1982, the American National Standard Committee B16 was reorganized as anASME Committee, operating under procedures accredited by ANSI.In 1991, the scope of the Stan

28、dard was changed from bronze pipe flanges and fittings to castcopper alloy flanges and flanged fittings, and it was expanded to include class designations 150,300, 600, 900, 1500, and 2500. The 1991 edition also established U.S. Customary units as thestandard, and editorial revisions were made to im

29、prove the text. Following approval by theStandards Committee and ASME, the 1991 edition of the Standard was approved as an AmericanNational Standard by ANSI on February 1, 1991, with the new designation ASME B16.24-1991and the new title “Cast Copper Alloy Pipe Flanges and Flanged Fittings.”In 2001,

30、the Standard was revised to include Nonmandatory Appendix A, Quality SystemProgram. Editorial revisions were made for clarification. Following approval by the B16 StandardsivCommittee and the ASME Supervisory Board, the Standard was approved as an AmericanNational Standard by ANSI on October 24, 200

31、1.In the 2006 edition, metric units became the primary reference units while maintainingU.S. Customary units in either parenthetical or separate forms. Requirements for Class 400 flangeswere omitted from the Standard. In addition, several editorial revisions were made for clarity.Following approval

32、by the Standards Committee and the ASME Board, ASME B16.24-2006, CastCopper Alloy Pipe Flanges and Flanged Fittings: Classes 150, 300, 600, 900, 1500, and 2500 wasapproved as an American National Standard by ANSI on November 9, 2006.In the 2011 edition, references to ASME Standards were revised to n

33、o longer list specificedition years; the latest edition of ASME publications applies unless stated otherwise. Materialsmanufactured to other editions of the referenced ASTM standards have been permitted to beused to manufacture fittings meeting the requirements of this Standard as long as the fittin

34、gmanufacturer verifies the material meets the requirements of the referenced edition. Followingapproval by the Standards Committee and the ASME Board on PTCS, the 2011 revision wasapproved as an American National Standard by ANSI on August 9, 2011, with the designationASME B16.24-2011.In this 2016 e

35、dition, provisions have been made to revise the scope and table readings, and anew Mandatory Appendix and a new Nonmandatory Appendix have been added. Followingthe approval by the ASME B16 Standards Committee, approval as an American National Standardwas given by ANSI on September 23, 2016, with the

36、 new designation ASME B16.24-2016 andthe new title “Cast Copper Alloy Pipe Flanges, Flanged Fittings, and Valves: Classes 150, 300,600, 900, 1500, and 2500.”vASME B16 COMMITTEEStandardization of Valves, Flanges, Fittings, and Gaskets(The following is the roster of the Committee at the time of approv

37、al of this Standard.)STANDARDS COMMITTEE OFFICERSR. M. Bojarczuk, ChairC. E. Davila, Vice ChairC. Ramcharran, SecretarySTANDARDS COMMITTEE PERSONNELA. Appleton, Alloy Stainless Products Co., Inc.J. E. Barker, Dezurik Water ControlsR. W. Barnes, Anric Enterprises, Inc.P. Milankov, Alternate, Consulta

38、ntK. Barron, Ward ManufacturingD. C. Bayreuther, Metso Automation, Flow Control DivisionW. B. Bedesem, ConsultantR. M. Bojarczuk, ExxonMobil Research and Engineering Co.A. M. Cheta, Qatar Shell GTLM. A. Clark, NIBCO, Inc.G. A. Cuccio, Capitol Manufacturing Co.J. DAvanzo, Fluoroseal ValvesC. E. Davil

39、a, Crane EnergyD. R. Frikken, Becht Engineering Co.R. B. Hai, RBH AssociatesSUBCOMMITTEEJCOPPER AND COPPER ALLOY FLANGES, FLANGED FITTINGS, AND SOLDER JOINT FITTINGSA. G. Kireta, Jr., Chair, Copper Development Association, Inc.M. A. Clark, Vice Chair, NIBCO, Inc.E. Lawson, Secretary, The American So

40、ciety of MechanicalEngineersJ. A. Ballanco, JB Engineering and Code Consulting PCS. L. Cavanaugh, Cavanaugh ConsultingW. E. Chapin, Professional Code Consulting, LLCA. Ciechanowski, NSF InternationalD. R. Frikken, Becht Engineering Co.viG. A. Jolly, ConsultantM. Katcher, Haynes InternationalT. A. Mc

41、Mahon, Emerson Process ManagementM. L. Nayyar, NICEW. H. Patrick, The Dow Chemical Co.D. Rahoi, ConsultantC. Ramcharran, The American Society of Mechanical EngineersR. A. Schmidt, CanadoilJ. Tucker, FlowserveF. R. Volgstadt, Volgstadt however, they should not contain proprietary names orinformation.

42、viiRequests that are not in the format described above may be rewritten in the appropriate formatby the Committee prior to being answered, which may inadvertently change the intent of theoriginal request.ASME procedures provide for reconsideration of any interpretation when or if additionalinformati

43、on that might affect an interpretation is available. Further, persons aggrieved by aninterpretation may appeal to the cognizant ASME Committee or Subcommittee. ASME does not“approve,” “certify,” “rate,” or “endorse” any item, construction, proprietary device, or activity.Attending Committee Meetings

44、. The B16 Standards Committee regularly holds meetingsand/or telephone conferences that are open to the public. Persons wishing to attend any meetingand/or telephone conference should contact the Secretary of the B16 Standards Committee.viiiASME B16.24-2016SUMMARY OF CHANGESFollowing approval by the

45、 ASME B16 Committee and ASME, and after public review,ASME B16.24-2016 was approved by the American National Standards Institute on September23, 2016.ASME B16.24-2016 includes the following changes identified by a margin note, (16). In addition,the title of the Standard was updated to include valves

46、. The Record Numbers listed below areexplained in more detail in the “List of Changes in Record Number Order” following this Summaryof Changes.Page Location Change (Record Number)1 1 Revised in its entirety (15-1068)2.2 Reference to Mandatory Appendix IIIupdated2.5 Revised to include valves (15-2830

47、)2.6 Revised to include valves (15-2830)2 3.1 (1) Subparagraphs (b) and (c) revised intheir entirety (15-863)(2) Subparagraph (d) deleted (15-863)3.3 References to paras. 6.5 and 6.6 updated(15-863)3.4 Revised to include valves (15-863)3.5 Revised (15-863)3.6 Revised to include valves (15-863)8 Tabl

48、e 6 Revised in its entirety (15-863)Table 7 Added (15-863)4.1 Revised to include valves (15-2830)5.1 Revised to include valves (15-863)5.1.2 Revised (15-863)5.1.3 Revised to include valves (15-2830)10 5.1.4 Revised to include valves (15-2830)5.1.5 Revised to include valves (15-2830)6.2.3 Revised (15

49、-863)6.2.3.4 Revised (15-2830)6.4 Added, and following paragraphsredesignated (15-2830)6.5 (1) Revised to include valves (15-2830)(2) References to paras. 6.5.1 and 6.5.2updated (15-2830)6.5.1 Revised to include valves (15-2830)6.5.2 Revised to include valves (15-2830)ixPage Location Change (Record Number)11 7 Title revised (15-863)7.1.1 Revised (15-863)7.1.2 Revised (15-863)7.1.3 Added (15-2830)7.2 Metric equivalent revised (15-2830)7.6 Revised in its entirety (11-560)7.9 Revised to include valves (15-2830)8 Title revised (15-2830)12 8.1.6 Added, and following paragraphredesi