ASD-STAN TR 7000-1-2002 Aerospace Series Non-Metallic Materials Rules for the Drafting and Presentation of Material Standards Part 1 General Rules (Edition 1 Supersedes prEN 7000-1.pdf

《ASD-STAN TR 7000-1-2002 Aerospace Series Non-Metallic Materials Rules for the Drafting and Presentation of Material Standards Part 1 General Rules (Edition 1 Supersedes prEN 7000-1.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN TR 7000-1-2002 Aerospace Series Non-Metallic Materials Rules for the Drafting and Presentation of Material Standards Part 1 General Rules (Edition 1 Supersedes prEN 7000-1.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、AECMA Technical Report TR 7000-1 Rapport Technique AECMA Edition 1 AECMA Fach bericht June 2002 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION Jn Gulledelle 94 - 8-1200 Brussels -Tel. + 32 2 775 81 10 - Fax. + 32 2 775 81 11 - www.aecma-stan.org Edition approved for

2、publication 28 June 2002 ICs: Descriptors: Extra copies can be supplied by B.N.A.E. Technopolis 54 - 199, rue Jean-Jacques Rousseau Non-metallic Material Domain 92138 ISSY - LES - MOULINEAUX CEDEX - FRANCE ENGLISH VERSION Aerospace series Non-metallic materials Rules for the drafting and presentatio

3、n of material standards Part 1 : General rules Supersedes prEN 7000-1 Edition PI September 1998 Srie arospatiale Luft- und Raumfahrt Matriaux non-mtalliques Nichtmetallische Werkstoffe Rgles pour la prparation et la prsentation des normes de materiaux Partie I : Rgles gnrales Regeln fr die Erstellun

4、g und die Gestaltung von Werkstoffnormen Teil 1: Allgemeine Regeln This Technical Report was drawn up by the Non-metallic Material Domain of AECMA-STAN. The reason which led to the publication of the document as a Technical Report is explained in the foreword. I I I I Copyright 2002 O by AECMA-STA/

5、Page 2 TR 7000-1 : 06-02 Foreword The main task of AECMA-STAN is to prepare EN standards. In exceptional circumstances, however, the publication of a Technical Report of one of the following types may be proposed : - type 1, the subject is still under technical development requiring wider exposure ;

6、 - type 2, a Technical Committee has collected data of a different kind from that which is normally published as a European Standard. The Non-metallic Material Domain decided to publish this document in the form of a Technical Report of type 2 in order to facilitate the updating of this document. Co

7、ntents Page Introduction . 1 Scope . 2 Normative references . 3 4 5 O Definitions, symbols and abbreviations . Rules for drafting and presentation . Rules for completion of tables Annex A (normative) Form 1: Table 1 Annex B (normative) Form 2: Tables 2 to 4 . . . Annex C (normative) Optional charact

8、eristics 3 3 3 3 5 7 10 11 12 Page 3 TR 7000-1 06-02 O Introduction This standard is part of the series of TR non-metallic materials standards for aerospace applications. The general organisation of this series is described in EN 4385. This document is a level 2 document as defined in EN 4385. 1 Sco

9、pe This standard specifies the general rules for the drafting and presentation of non-metallic material standards, for aerospace applications. It is supported by additional rules specific to each family, defined in TR 7000-2 onwards. 2 Normative references This European Standard incorporates by date

10、d or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the next and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard o

11、nly when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. IS0 31-0 IS0 31-1 IS0 31-3 IS0 31-4 IS0 31-1 1 IS0 1000 EN 4385 TR 7000-2 Quantities and units - Pari O: General principles Quantities and units - Part 1 : Space an

12、d time Quantities and units - Part 3: Mechanics Quantities and units - Part 4: Heat Quantities and units - Part 11: Mathematical signs and symbols for use in the physical sciences and technology SI units and recommendations for the use of their multiples and of certain other units Aerospace series -

13、 Non-metallic materials - General organisation of standardisation - Links between types of standards 1) Aerospace series - Non-metallic materials - Rules for the drafting and presentation of material standards - Part 2: Rubbers 2) 3 Definitions, symbols and abbreviations 3.1 Defi nit ions For the pu

14、rpose of this standard the following definitions apply: 3.1.1 material standard a standard specifying a series of requirements relating to a non-metallic material, which may be a semi- finished product, such as: - one or more delivery conditions, - one reference set of processing conditions for acce

15、ptance test and qualification purposes which may differ from the use condition intended by the user, - series of technical requirements for these different conditions NOTE A material standard may also specify one or more than one use condition, providing that the variants are not interconvertable. S

16、uch cases shall be clearly identified by the designation system given in the material standard. 1) Published as AECMA Prestandard at the date of publication of this standard 2) Published as AECMA Technical Report at the date of publication of this standard Page 4 TR 7000-1 : 06-02 3.1.2 family of no

17、n-metallic material a group of non-metallic materials characterised by basic descriptions generally in semi-finished product forms such as but not exclusively: - rubbers, - sealants, - transparent plastics, - glass, - adhesives, - anaerobic polymerizable compounds, - honeycombs, - paints, - reinforc

18、ement fibre, - preimpregnates, - textiles 3.1.3 semi-finished products a generic term used to indicate that the material as delivered is in an intermediate form to that occuring in the final component This term may refer to the following: - adhesives where one delivered condition may be a two-part m

19、ix and the final use condition is the cured adhesive; - preimpregnates, which are subsequently shaped to produce a part with specified characteristics; - honeycomb which may be shaped and formed. 3.1.4 type of semi-finished products semi-finished product forms (sheets, rolls, tube, cloths, liquids,

20、paste etc.) associated with the relevant family of non-metallic materials 3.1.5 final condition of use the condition of the material in which no further processing (except machining or shaping) is required before use 3.2 Symbols and abbreviations For the purpose of this standard, the following symbo

21、ls and abbreviations shall apply: Abbreviations shall be taken from IS0 31. The following for sizes and units shall be taken from IS0 31-1, IS0 31-3, IS0 31-4, IS0 31-11 and IS0 1000. The following are typical symbols used: - %”for thickness; - ”b”for width; - lfor length; - Dfor outside diameter; -

22、 “”for inside diameter; - “afor temperature; - “f”for time; - “RH”for relative humidity. NOTE The abbreviation “min.”, for minimum shall not be used. When it is necessary to state a minimum or maximum value this shall be done using the symbols , , alternatively the word shall be written in full. The

23、 exception to this in when “min.” and ”max.” are defined for other uses within abbreviations, e.g. Rmax. or - The family of the non-metallic material; - Form or forms, written in singular or plural, in conformity with the language used and, if appropriate, the method of production andlor final use;

24、- Dimensions if appropriate; - Relevant mechanical or physical limits if appropriate. 4.2 Clause O: Introduction When required, this clause shall read: O Introduction This standard is part of the series of EN non-metallic materials standards for aerospace applications. The general organisation of th

25、is series is described in EN 4385. This standard is a level 3 document as defined in EN 4385. It has been prepared in accordance with (hserf relevant TR 7000 Part number). 4.3 Clause I: Scope This clause shall read: Scope This standard specifies the requirements relating to . (repeat all the informa

26、tion in the title in a grammatical sequence that satisfies the language used . for aerospace applications. (Followed by any additional information, as necessaty, to clarify the field of application). 4.4 Clause 2: References This clause shall read: 2 This European Standard incorporates by dated or u

27、ndated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only whe

28、n incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Nor ma tive refe re n ces Footnotes shall indicate: - for AECMA documents the relevant status (if not EN), - for other documents the body responsible for the publication (

29、except ISOAEC). Page 6 TR 7000-1 : 06-02 4.5 4.5.1 Clause 3.1: Definitions This clause shall read : Clause 3: Definitions, symbols and abbreviations 3.1 Definitions For the purpose of this standard, the following definitions apply: 3.1.1 Sub-case numbering In the column requirement at the left side

30、a sub-case number is given, The definition of these sub- case numbers is as follows: Sub-case number Definitions - Technical specification I Test method 2 Frequency of testing 3 Sample type 4 Test piece definition 5 Conditioning of test piece 6 Testing condition 7 Acceptance criteria NOTE 1 standard

31、, e.g. in the reference to the technical standard (characteristic number 1.004). The absence of a sub-case indicates that the necessary information is given in table 1 of this All the necessary information which does not appear is to be found in the referenced technical specification or the relevant

32、 test method. NOTE 2 In this material standard, batch acceptance test titles and sub-cases 7 acceptance criteria are highlighted in the form of bold frame and bold characters to show they are mandatory for routine release of the material. 3.1.2 Other definitions Continue sub-clause numbering as nece

33、ssary. 4.5.2 This clause shall read : Clause 3.2 : Symbols and abbreviations 3.2 Symbols and abbreviations For the purpose of this standard, the following symbols and abbreviation apply: Followed by a list of symbols and abbreviations. 4.6 Clause 4: Requirements The material standard requirements ar

34、e given in a series of tables. The format of these tables, and rules for their completion, are given in clauses 3.1.1, 5.1 and 5.2 of this standard. Within each material standard, the following clause shall be used: 4 Requirements The required characteristics are given in: Table 1 : General requirem

35、ents Table 2: Requirements in the delivery condition Table 3: Requirements as processed to characteristic number 1 .O13 Table 4: Environmental testing requirements as processed to characteristic number 1 .O1 3. Page 7 TR 7000-1 : 06-02 - I 2 3 4 5 6 7 5 Rules for completion of tables Technical speci

36、fication Test method Frequency of testing Sample type Test piece definition Conditioning of test piece Testing condition Acceptance criteria 5.1 Format of tables 5.1.1 Table I: see Annex A This form is mandatory irrespective of the family of non-metallic material. The actual format is dependent on t

37、he family of non-metallic material. This form describes the general characteristics of the product, and is applicable to all non-metallic material standards. 5.1.2 This form shall be used for each of the following three tables for which it is required to specify requirements. When required optional

38、characteristic selected from annex C shall be completed as follows: Tables 2 to 4: see Annex B Table 2, requirements in the delivery condition (column 0 optional (see figure 1): add line or case number). Table 3, requirements as processed to characteristic number 1.013 (column 0 optional: add line o

39、r case number). Table 4, environmental testing requirements as processed to characteristic number 1 .O13 (column 0 optional: add line or case number). The characteristic numbers, (see annex C) shall be written in column (see figure I), and shall be pre-fixed with the table number. When more than one

40、 characteristic number applies for a particular requirement, both characteristic numbers shall be shown in column 0. The characteristic titles shall be written in column 0 (see figure I), including any information to clarify the requirements. Column (see figure I) shall be completed with a sub-case

41、number corresponding to the information to be given in column 0 (see figure 1) and selected from the following: 0 Case number or line number (optional) I Characteristic number 0 Characteristic Sub-case number 7 - Figure I Page 8 TR 7000-1 : 06-02 - A sub-case shall be omitted, if the necessary infor

42、mation is given in the technical specification referenced in 1.004. - If all the necessary information is contained in the technical specification, the sub-case is opened by stating “see EN xxxx“. In this case a hyphen is inserted in the third column. No other sub-case number will be given. - If the

43、 technical specification or the test method: - does not give any information, - only gives partial information, - or gives a choice, or if the requirements differ from those given in the technical specification or test method, then sub- cases 1 !o 7 shall be completed as required with the necessary

44、information. - Column 0 is completed, in accordance with the specific instructions given in the relevant dash numbered part of this standard. Values which will be agreed during qualification shall be expressed as a range in the material standard, e: No “X values to be specified in material standards

45、. It is only necessary to complete those sub-cases for which information is required to be specified. 5.2 5.2.1 General The column 0 (see figure 1) is optional. If used, the case number shall be consecutive. Alternatively, it can be replaced by a consecutive line numbering as indicated in the dash n

46、umber part. If there is insufficient width in a column then information shall be repeated below and marked “continued“. General instructions for completion of the tables 5.2.2 Table 1 See annex A. If material is supplied in its final condition of use, for characteristic number 1.013, write: I I vies

47、sing condition Supplied in final condition of use 5.2.3 Tables 2 to 4 This form shall be filled in accordance with the relevant part of this standard (see TR 7000-2 onwards). If all the characteristics covered by that particular table are not required, keep the table heading and write: No requiremen

48、ts I If the characteristics covered by table 2 are the same as table 3 (.e. delivery condition is final condition of use) then keep the table 2 heading and write: No requirements: see table 3. NOTE material standards. Test requirements shown in the technical specification are only mandatory when ref

49、erenced in the Page 9 TR 7000-1: 06-02 Where one or more of the test requirements defined as follows: - test method, - frequency of testing, - sample type, - test piece definition, - condition of test piece, - testing condition, - acceptance criteria are not specified or differ from the requirements of the technical specification or test method, they shall be included by means of one or more sub-case numbers in accordance with the instructions given in 4.4.2. 5.2.4 Batch release testing In the material standards, batch release test titles a