ASD-STAN PREN 6055-2018 Aerospace series - Rod-end with bearing per EN 4265 in corrosion resisting steel external threaded shank - Dimensions and loads - Inch series (Edition P 2).pdf

《ASD-STAN PREN 6055-2018 Aerospace series - Rod-end with bearing per EN 4265 in corrosion resisting steel external threaded shank - Dimensions and loads - Inch series (Edition P 2).pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 6055-2018 Aerospace series - Rod-end with bearing per EN 4265 in corrosion resisting steel external threaded shank - Dimensions and loads - Inch series (Edition P 2).pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 6055 Edition P2 February 2018 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.org ICS: Descriptors: ENG

2、LISH VERSION Aerospace series Rod-end with bearing per EN 4265 in corrosion resisting steel, external threaded shank Dimensions and loads Inch series Luft- und Raumfahrt senkopf mit Gelenklager nach EN 4265 aus korrosionsbestndigem Stahl, mit Auengewinde Mae und Belastungen Inch Reihe Srie arospatia

3、le Embout rotule lisse en acier par EN 4265 rsistant la corrosion avec le filetage extrieur Dimensions et charges Srie en inches This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization).

4、It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is a

5、ffected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transfor

6、mation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves that: “This document is publishe

7、d by ASD-STAN for the needs of the European Aerospace Industry. The use of this standard is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” ASD-STAN reviews each standard a

8、nd technical report at least every five years at which time it may be revised, reaffirmed, stabilized or cancelled. ASD-STAN invites you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system

9、or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1stFebruary 2018 Comments should be

10、 sent within six months after the date of publication to ASD-STAN Mechanical Domain prEN 6055:2018 (E) 2 Contents Page Foreword 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Symbols and Definition . 6 4 Requirements . 6 4.1 Configuration, dimensions, tolerances and mass 6 4.2 Surface roughne

11、ss . 6 4.3 Right or left hand thread 9 4.4 With or without longitudinal groove 10 4.5 Material 10 4.6 Surface treatment 10 4.7 Loads . 11 4.8 Clearance . 12 4.9 Temperature range and lubricant . 12 5 Designation. 13 6 Marking 13 7 Technical specification . 13 8 Quality management systems 13 (normati

12、ve) Verification of fatigue loads 14 Annex AA.1 Standard rod end fatigue spectrum . 14 A.2 Method . 14 (informative) Standard evolution form . 15 Annex BBibliography . 16 prEN 6055:2018 (E) 3 Foreword This document (prEN 6055:2018) has been prepared by the Aerospace and Defence Industries Associatio

13、n of Europe Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member of ASD, prior to its presentation to CEN. prEN 6055:2018 (E) 4

14、Introduction This document is published at edition P2. Former P1 and drafts may exist of Airbus development only but without any ASD-STAN official publication. In consequence configuration management discrepancies with these unofficial documents are under Airbus responsibility. prEN 6055:2018 (E) 5

15、1 Scope This European standard specifies the characteristics of adjustable rod ends consisting of: a spherical plain bearing, metal to metal, in corrosion resisting steel, wide series (EN 4265); a rod-end with threaded shank with an optional longitudinal groove for locking purposes. They are intende

16、d for use in fixed or moving parts of the aircraft structure and their control mechanisms. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cite

17、d applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2133, Aerospace series Cadmium plating of steels with specified tensile strength 1 450 MPa, copper, copper alloys and nickel alloys1) EN 2424, Aerospace series Marking of aerospace

18、 products EN 4265, Aerospace series Bearing spherical plain, metal to metal in corrosion resisting steel Wide series Dimensions and loads Inch series2)EN 6099, Aerospace series Rod-end with spherical plain bearing, metal to metal Technical Specification2)ISO 1132-1, Rolling bearings Tolerances Part

19、1: Terms and definitions ISO 3161, Aerospace UNJ threads General requirements and limit dimensions ISO 3353-1, Aerospace Lead and runout threads Part 1: Rolled external threads ISO 3353-2, Aerospace Lead and runout threads Part 2: Internal threads ISO 8074, Aerospace Surface treatment of austenitic

20、stainless steel parts MIL-PRF-23827, Grease, aircraft and instrument, gear and actuator screw, NATO Code No.G-354 metric3) MIL-PRF-46010, Lubricant, solid film, heat cured, corrosion inhibiting, NATO Code-S-17384)MIL-PRF-81322, Grease, aircraft, general purpose, wide temperature range, NATO Code-G-3

21、954)NAS 559, Lock-rod end (key type)4)1) Published as ASD-STAN Standard at the date of publication of this European standard (www.asd-stan.org). 2) In preparation at the date of publication of this European standard (www.asd-stan.org). 3) Published by: Department of Defense (DoD), the Pentagon, Wash

22、ington, D.C., 20307, USA. 4) Published by: Aerospace Industries Association of America, Inc. (AIA), 1250 Eye Street, N.W., Washington, D.C. 20005-3924, USA prEN 6055:2018 (E) 6 SAE AMS 5643, Steel, corrosion resistant, bars wire, forgings, tubing and rings 16Cr-4.0Ni-0.30(Cb+Ta)-4.0Cu solution heat

23、treated, precipitation hardenable TR 4475, Aerospace series Bearings and mechanical transmissions for airframe applications Vocabulary 3 Symbols and Definition Symbols of limit deviations are in accordance with definitions of ISO 1132-1. maximum angle of tilt of the outer ring with respect to the in

24、ner ring, with the spherical surface of the outer ring being completely in contact with the inner ring Cspermissible static radial load dmpsingle plane mean bore diameter deviation dsdeviation of a single bore diameter Cppush out load Cffatigue load For definitions and vocabulary, see TR 4475. 4 Req

25、uirements 4.1 Configuration, dimensions, tolerances and mass Configuration, dimensions, tolerances and mass should be according to Figure 1 and Table 1. Table 1 and Table 5: Dimensions and tolerances are expressed in millimeters (inches). Figure 1: Dimensions and tolerances for Ra max. are expressed

26、 in m (in). Values apply after surface treatment. 4.2 Surface roughness Surface roughness should be according to Figure 1. Surface roughness is measured before surface treatment. prEN 6055:2018 (E) 7 Key a) runout according to ISO 3353. b) thread, pitch diameter. c) groove as per NAS 559. d) usable

27、length for groove. e) 0,127 to 0,381 (0.005 to 0.015) radius or chamfer 45 Figure 1 Configuration prEN 6055:2018 (E) 8 Table 1 Dimensions, tolerances and mass Dia-meter codeaD3 D4bd D1 D2 B C Type of thread UNJF-3A Limit deviation 0 0,127 0,051 nominal max. dmp ds Bearing diameter min. (0 (0.005) 0.

28、002) 03 0.3125-24 7,249 (0.2854) 4,826 (0.1900) 15,875 (0.6250) 7,620 (0.300) 11,100 (0.437) 8,560 (0.337) 04 6,350 (0.2500) 041 05 7,937 (0.3125) 17,463 (0.6875) 9,144 (0.360) 8,306 (0.327) 06 0.3750-24 8,837 (0.3479) 9,525 (0.3750) 20,638 (0.8125) 11,836 (0.466) 12,700 (0.500) 10,566 (0.416) 07 0.

29、4375-20 10,287 (0.4050) 11,113 (0.4375) 23,017 (0.9062) 13,640 (0.537) 14,275 (0.562) 11,481 (0.452) 71 08 0.5000-20 11,875 (0.4675) 12,700 (0.5000) 25,400 (1.0000) 15,418 (0.607) 15,878 (0.625) 13,081 (0.515) 0 0 10 0.6250-18 14,958 (0.5889) 15,875 (0.6250) 0,013 0,013 30,163 (1.1875) 18,974 (0.747

30、) 19,050 (0.750) 14,656 (0.577) (0 (0 0.0005) 0.0005) 12 0.7500-16 18,019 (0.7094) 19,050 (0.7500) 34,925 (1.3750) 21,463 (0.845) 22,225 (0.875) 16,256 (0.640) 14 0.8750-14 21,046 (0.8286) 22,225 (0.8750) 41,275 (1.6250) 25,273 (0.995) 19,431 (0.765) 16 1.2500-12 30,376 (1.1959) 25,400 (1.0000) +0,0

31、03 0,015 (+0.0001 0.0006) 53,975 (2.1250) 32,233 (1.269) 34,925 (1.375) 25,781 (1.015) prEN 6055:2018 (E) 9 Dia-meter codeab1 b2 l1 l2 l3 r cA Mass 0 +0,127 0,254 +1,524 0,762 +1,524 0,76 0,254 0,254 g/piece 0,127 0 (0 (+0.0050 (0.010) (+0.060 0.030) (+0.060 0.030) (0.010) min. (0.010) 0.0050) 0) 03

32、 6,604 (0.260) 1,575 (0.062) 39,675 (1.562) 25,400 (1.000) 25,400 (1.000) 6,477 (0.255) 16,0 20,498 (0.807) 33 04 041 52,095 (2.051) 37,008 (1.457) 37,008 (1.457) 36 05 47,625 (1.875) 26,975 (1.062) 26,975 (1.062) 15,5 22,911 (0.902) 39 06 7,899 (0.311) 2,362 (0.093) 49,225 (1.938) 31,750 (1.250) 31

33、,750 (1.250) 9,5 26,010 (1.024) 62 07 9,398 (0.370) 53,975 (2.125) 34,925 (1.375) 34,925 (1.375) 11,0 29,210 (1.150) 83 71 66,129 (2.606) 90 08 11,074 (0.436) 61,925 (2.438) 38,100 (1.500) 38,100 (1.500) 9,5 34,011 (1.339) 126 10 13,741 (0.541) 3,175 (0.125) 66,675 (2.625) 41,275 (1.625) 41,275 (1.6

34、25) 12,0 38,710 (1.524) 192 12 16,840 (0.663) 73,025 (2.875) 44,450 (1.750) 44,450 (1.750) 8,077 (0.318) 14,0 45,110 (1.776) 290 14 19,736 (0.777) 3,962 (0.156) 85,725 (3.375) 47,625 (1.875) 47,625 (1.875) 6,0 51,410 (2.024) 437 16 28,854 (1.136) 4,750 (0.187) 104,775 (4.125) 53,975 (2.125) 53,975 (

35、2.125) 9,703 (0,382) 14,5 70,510 (2.776) 1140 aThe diameter code corresponds to nominal diameter d in 1/16 inch. b Rolled threads according to ISO 3161.c The acceptance value is the maximum value for user. 4.3 Right or left hand thread Right or left hand thread should be according to Table 2. Table

36、2 Right or left hand thread Code Right or left hand thread R right hand thread L left hand thread prEN 6055:2018 (E) 10 4.4 With or without longitudinal groove With or without longitudinal groove should be according to Table 3. Table 3 With or without longitudinal groove Code With or without longitu

37、dinal groove K with longitudinal groove F without longitudinal groove 4.5 Material Inner ring: See product standard EN 4265. Outer ring: See product standard EN 4265. Rod end body: See AMS 5643, hardness 35 HRC 42. 4.6 Surface treatment Surface treatment as defined in chapter 5 (designation) with fo

38、llowing codes: Rod end body: code T: passivated according to ISO 8074; code P: cadmium plating and chromating according to EN 2133, 10 m to 20 m (400 in to 800 in); exception: threads, 5 m to 15 m (200 in to 600 in); bearing: See EN 4265. prEN 6055:2018 (E) 11 4.7 Loads Loads should be according to

39、Table 4. Table 4 Loads Diameter codea Radial Axial static proof loadc, gFatigue loaddPermissible static loads Ultimate load 2 106cycles kN kN kN kN CsbCpCf03 10,7e16,1e4,7 3,3 04 20,0 30,0 041 20,0 30,0 05 20,0 h 30,0 5,2 3,3 06 28,8 43,2 7,6 4,8 07 36,8 55,3 8,4 6,1 71 08 57,2f85,8f9,3 9,4 10 66,6

40、99,9 11,1 11,0 12 88,3 132,5 14,4 14,5 14 102,4 153,6 17,0 16,9 16 231,1 346,6 22,2 38,1 aThe diameter code corresponds to nominal diameter d in 1/16 inch. bDefinition and testing according to EN 6099, Annex A. cDefinition and testing according to EN 6099, Annex B. dDefinition and testing according

41、to Annex A (EN 6099, Annex D). (permissible surface pressure: 100 MPa on smallest rodend-section) attention: the thread-rod must support this fatique load. eLimited by bolt bending. fLimited by rod thread. gAfter removing the load no permanent displacement of the bearing in the rod-end greater than

42、0,10 mm is permitted. prEN 6055:2018 (E) 12 4.8 Clearance Clearance should be according to Table 5. Table 5 Clearance Diameter code ClearanceaRadial Axial normal reduced normal reduced Code N Code P Code N Code P max. max. 03 0,010 to 0,030 (0.0004 to 0.0012) 0,002 to 0,010 (0.0001 to 0.0004) 0,120

43、(0.0047) 0,035 (0.0014) 04 041 05 06 07 71 08 0,010 to 0,050 (0.0004 to 0.0020) 0,002 to 0,010 (0.0001 to 0.0004) 0,229 (0.0090) 10 0,003 to 0,012 (0.0001 to 0.0005) 0,040 (0.0016) 12 0,004 to 0,015 (0.0002 to 0.0006) 0,050 (0.0020) 14 16 aDefinition and testing according to EN 6099, Annex C. 4.9 Te

44、mperature range and lubricant They shall be used in the temperature range 55 C to 150 C. As they are lubricated by means of the following greases: code A: grease as per MIL-PRF-23827 type 1, operating temperature range 73 C to 121 C; code B: grease as per MIL-PRF-81322, operating temperature range 5

45、4 C to 177 C. The range of application for bearings lubricated with grease per code A is limited to 121 C. In both cases the spherical surface of the outer or inner ring, have to be provided with a dry-film lubricant as per MIL-PRF-46010 or equivalent (anti-seizing protection). prEN 6055:2018 (E) 13

46、 5 Designation EXAMPLE NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking Marking should be according to EN 2424, style A. 7 Technical specification Marking should be according to according to EN 6099. 8 Quality management systems The ma

47、nufacturers operations shall be an approved production organisation for aerospace products and shall demonstrate that it has implemented and is able to maintain a quality management system (e. g. according to EN 9100 or another in aerospace accepted and established quality management system). The qu

48、alification procedure for aerospace standard products (e. g. according to EN 9133 or another in aerospace accepted and established qualification procedure) shall be used and documented according to the specified tests if not otherwise agreed between customer and supplier. prEN 6055:2018 (E) 14 Annex

49、 A(normative) Verification of fatigue loads A.1 Standard rod end fatigue spectrum See Figure A.1. A.2 Method The loading shall be tensionedwith the maximum load equal to the fatigue load given on applicable EN standard and with the minimum load equal to 10 % of the fatigue load see typical fatigue spectrum in Figure A.1. Loads shall be maintained within 2 % and testing speed shall not exceed 50 Hz. Rod ends shall