ASD-STAN PREN 4710-06-2014 Aerospace series Quick release fastening systems for non-structural applications Part 06 Stud - quick-release and locking (Edition P 1).pdf
《ASD-STAN PREN 4710-06-2014 Aerospace series Quick release fastening systems for non-structural applications Part 06 Stud - quick-release and locking (Edition P 1).pdf》由会员分享,可在线阅读,更多相关《ASD-STAN PREN 4710-06-2014 Aerospace series Quick release fastening systems for non-structural applications Part 06 Stud - quick-release and locking (Edition P 1).pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4710-06 Edition P 1 February 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Descriptors: ENGLISH VER
2、SION Aerospace series Quick release fastening systems for non-structural applications Part 06: Stud - quick-release and locking Srie arospatiale Fixations rapides filetes pour applications non-structurales Partie 06 : Pion dmontage et verrouillage rapide Luft- und Raumfahrt Druckverschlsse nicht-str
3、ukturelle Anwendungen Teil 06: Bolzen - Schnell Auslsend und Schlieend This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace In
4、dustry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identifica
5、tion of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then
6、 to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 28 February 2014 Comments should be sent within six months after the date of publication to ASD-STAN Mechanica
7、l Domain Copyright 2014 by ASD-STAN prEN 4710-06:2014 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Requirements . 4 4 Designation 7 5 Marking . 7 6 Technical specification . 8 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Mechanical Domai
8、n. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4710-06:2014 (E) 3 1 Scope This standard specifies the dimensions, mass, tolerances and static values of stud - qui
9、ck-release and locking for use in fuselage interior equipment and non- structural or secondary structural area. This standard part shall be used in conjunction with EN 4710-03, EN 4710-04, EN 4710-05 and EN 4710-07 as described in EN 4710-02. The applicable temperature range is 55 C to 85 C. 2 Norma
10、tive references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking
11、 of aerospace products EN 2516, Aerospace series Passivation of corrosion resistant steels and decontamination of nickel base alloys EN 4710-01, Aerospace series Quick release fastening systems for non-structural applications Part 01: Technical specification 1)EN 4710-02, Aerospace series Quick rele
12、ase fastening systems for non-structural applications Part 02: Stud spring clamp family 1)EN 4710-03, Aerospace series Quick release fastening systems for non-structural applications Part 03: Spring clamp 1)EN 4710-04, Aerospace series Quick release fastening systems for non-structural applications
13、Part 04: Spring clamp One way tolerance compensation 1)EN 4710-05, Aerospace series Quick release fastening systems for non-structural applications Part 05: Spring clamp Two ways tolerance compensation 1)EN 4710-07, Aerospace series Quick release fastening systems for non-structural applications Par
14、t 07: Retaining grommet 1)EN 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes EN 12165, Copper and copper alloys Wrought and unwrought forging stock ISO 1456,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASDSTANPREN4710062014AEROSPACESERIESQUICKRELEASEFASTENINGSYSTEMSFORNONSTRUCTURALAPPLICATIONSPART06STUDQUICKRELEASEANDLOCKINGEDITIONP1PDF

链接地址:http://www.mydoc123.com/p-453529.html