ASD-STAN PREN 4652-001-2014 Aerospace series Connectors coaxial radio frequency Part 001 Technical specification (Edition P 1).pdf

《ASD-STAN PREN 4652-001-2014 Aerospace series Connectors coaxial radio frequency Part 001 Technical specification (Edition P 1).pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 4652-001-2014 Aerospace series Connectors coaxial radio frequency Part 001 Technical specification (Edition P 1).pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4652-001 Edition P 1 January 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION

2、 Aerospace series Connectors, coaxial, radio frequency Part 001: Technical specification Srie arospatiale Connecteurs coaxiaux pour radio frquences Partie 001 : Spcification technique Luft- und Raumfahrt Hochfrequenz Steckverbinder, koaxial Teil 001: Technische Lieferbedingungen This “Aerospace Seri

3、es“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following m

4、ember comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STA

5、N, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard a

6、nd by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 January 2014 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2014 by ASD-STAN prEN 4652-001:2014 (E) 2 Contents Page Foreword 2 1 Scop

7、e 3 2 Normative references 3 3 Terms and definitions . 3 4 Description . 4 5 Definition and mass . 5 6 Test methods . 20 7 Quality assurance 25 8 Designation and marking 33 9 Packaging . 34 10 Packing . 34 11 Storage 34 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-S

8、TANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4652-001:2014 (E) 3 1 Scope This standard specifies the required characteristics, test methods

9、, qualification and acceptance conditions of coaxial, radio frequency connectors used with flexible radio frequency cables in accordance with EN 4604-001 and semi-rigid coaxial cables. This family of connectors is derived from MIL-PRF-39012. Front face dimensions are identical and products are fully

10、 intermateable. Cables usable with present specification are listed in TR 6058. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undate

11、d references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 2591 1), Aerospace series Elements of electrical and optical connection Test methods EN 3909, Aerospace series Test fluids and test methods for e

12、lectric components and sub-assemblies EN 4604-001, Aerospace series Cable, electrical, for signal transmission Part 001: Technical specification EN 4652-002, Aerospace series Connectors, coaxial, radio frequency Part 002: specification performances 2)EN 9133, Aerospace series Quality management syst

13、ems Qualification procedure for aerospace standard parts MIL-HDBK-454, General Guidelines for Electronic Equipment 3)MIL-PRF-39012, Connectors, coaxial, radio frequency General specification for 3)TR 6058, Aerospace series Cable code identification list 4)3 Terms and definitions For the purposes of

14、this document, the terms and definitions given in EN 2591-100 apply. 1) All parts quoted in this standard. 2) In preparation at the date of publication of this standard. 3) Published by : DoD National (US) Mil. Department of Defense http:/www.defenselink.mil/ 4) Published as ASD-STAN Technical Repor

15、t at the date of publication of this standard. http:/www.asd-stan.org/ prEN 4652-001:2014 (E) 4 4 Description 4.1 Types of connectors The characteristics of types of coaxial radio frequency connectors are defined in this standard. Type 1: BNC interface, 50 impedance, bayonet coupling. Type 2: TNC in

16、terface, 50 impedance, screw-on coupling. Type 3: N interface, 50 impedance, screw-on coupling. Type 4: C interface, 50 impedance, bayonet coupling. Type 5 : HN interface, 50 impedance, screw-on coupling Type 6 : SMA interface, 50 impedance, screw-on coupling 4.2 Models of connectors Models of conne

17、ctors are defined in this standard. Model code 0: straight plug. Model code 1: right angle plug. Model code 2: square flange receptacle. Model code 3: bulkhead receptacle. Model code 4: adaptor. 4.3 Technologies of assembly Cable and connector assemblies are defined in this standard. Code 0: solder

18、type. Code 1: clamp type. Code 2: crimp type. 4.3.1 Solder technology The core and the braid of the cable are soldered to the connector. 4.3.2 Clamp technology The core of the cable is plugged into the centre contact. A clamp nut fixes the braid of the cable onto the body of the connector (see produ

19、ct standard). prEN 4652-001:2014 (E) 5 4.3.3 Crimp technology The core of the cable is crimped (or soldered see product standard) into the centre contact. A ferrule crimps the braid of the cable onto the body of the connector (see product standard). 4.4 Permissible cables The permissible coaxial cab

20、les shall be specified in the product standard. Their cable codes are given by TR 6058. 4.5 Materials and surface treatments See product standard. 5 Definition and mass 5.1 Dimensions and masses The general dimensions and masses of the straight plug, right angle plug, square flange receptacle, bulkh

21、ead receptacle and adaptor are given in the product standard. prEN 4652-001:2014 (E) 6 5.2 Interface dimensions 5.2.1 Type 1 connectors BNC interface 5.2.1.1 Plug, 50 See Figure 1 and Table 1. Dimensions in millimetres Key 1 REF. Plane Figure 1 BNC plug interface Table 1 BNC plug dimensions Dimensio

22、ns in millimetres A B C D E F H K L M N P Q S T U V min. 9,78 4,83 1,32 5,33 0,15 11,76 2,31 0,08 179 5,28 1,98 0,46 4,57 3,15 14,5max. 9,91 8,31 1,37 5,84 12,01 2,46 181 0,64 5,79 0,56 4,67 15,5NOTE Slotted and flared to meet electrical and mechanical performance. prEN 4652-001:2014 (E) 7 5.2.1.2 R

23、eceptacle, 50 See Figure 2 and Table 2. Dimensions in millimetres Key 1 REF. Plane Figure 2 BNC receptacle interface Table 2 BNC receptacle dimensions Dimensions in millimetres A B C D E F G H J L M N P Q R S T U min. 10,97 9,60 8,31 8,10 5,18 8,31 1,91 4,72 4,95 2,06 8,79 0,38 10,52 4,78 179max. 11

24、,07 9,70 8,46 8,15 4,72 5,28 8,51 2,06 5,23 2,21 9,04 0,15 6,5 0,76 5,28 181NOTE 1 Q dimension applies to that portion (if applicable) of the dielectric which protrudes beyond the metal shoulder (or reference plane) by dimension P. NOTE 2 Clearance for mating connector coupling nut. prEN 4652-001:20

25、14 (E) 8 5.2.2 Type 2 connectors TNC interface 5.2.2.1 Plug, 50 , style A See Figures 3a and Table 3a. Dimensions in millimetres Key 1 REF. Plane Figure 3a TNC plug style A interface Table 3a TNC plug style A dimensions Dimensions in millimetres A B C D F G H J K L M P Q R min. 1,32 4,83 11,18 3,96

26、5,28 0,15 0,08 5,33 1,60 1,98 max. 1,37 8,31 5,79 1,98 1,02 5,84 8,18 0,64 NOTE Flared to meet electrical and mechanical performance. prEN 4652-001:2014 (E) 9 5.2.2.2 Plug, 50 , style B See Figure 3b and Table 3b. Dimensions in millimetres Key 1 REF. Plane Figure 3b TNC plug style B interface Table

27、3b TNC plug style B dimensions Dimensions in millimetres A B C D F G H K L M P R min. 1,32 6,05 11,18 3,96 5,28 0,08 5,33 1,60 1,98 max. 1,37 6,15 8,09 5,79 1,98 1,02 5,84 0,64 prEN 4652-001:2014 (E) 10 5.2.2.3 Plug, 50 , style C See Figure 3c and Table 3c. Dimensions in millimetres Key 1 REF. Plane

28、 Figure 3c TNC plug style C interface Table 3c TNC plug style C dimensions Dimensions in millimetres A B C D F G H J K L M P Q R min. 1,32 4,83 11,18 3,96 5,28 0,15 0,08 5,33 1,60 1,98 max. 1,37 8,09 5,79 1,98 1,02 5,84 8,18 0,64 prEN 4652-001:2014 (E) 11 5.2.2.4 Receptacle, 50 See Figure 4 and Tabl

29、e 4. Dimensions in millimetres Key 1 REF. Plane Figure 4 TNC receptacle interface Table 4 TNC receptacle dimensions Dimensions in millimetres A B C D E F G H J K L M N P Q R min. 8,10 8,31 8,79 9,60 2,06 8,31 1,73 4,72 4,78 4,75 0,38 10,52 4,95max. 4,72 8,15 8,46 9,04 9,68 2,21 8,51 2,24 0,15 5,23 5

30、,28 0,76 6,50 NOTE 1 Q dimension applies to that portion (if applicable) of the dielectric which protrudes beyond the metal shoulder (or reference plane) by dimension J. NOTE 2 Clearance for mating connector coupling nut. prEN 4652-001:2014 (E) 12 5.2.3 Type 3 connectors N interface 5.2.3.1 Plug, 50

31、 See Figure 5 and Table 5. Dimensions in millimetres Key 1 REF. Plane Figure 5 N plug interface Table 5 N plug dimensions Dimensions in millimetres A B C D E F G H J K M N min. 0,08 2,79 5,33 0,41 4,50 4,01 10,11 7,98 16,0 20,90 1,60 max. 1,03 3,56 5,84 1,52 4,27 10,46 8,38 21,7 1,68 0,25 NOTE 1 Slo

32、ts optional (flared to meet electrical and mechanical performance). NOTE 2 Compensating ring optional. NOTE 3 Radius or chamfer, shape of tip optional. prEN 4652-001:2014 (E) 13 5.2.3.2 Receptacle, 50 See Figure 6 and Table 6. Dimensions in millimetres Key 1 REF. Plane Figure 6 N receptacle interfac

33、e Table 6 N receptacle dimensions Dimensions in millimetres A B C D E F G H J K L M min. 9,04 4,75 1,19 4,37 6,76 10,72 8,03 8,53 3,02 5,33 max. 9,19 5,26 1,96 5,13 7,06 8,13 8,74 15,93 3,15 NOTE Clearance for mating connector coupling nut. prEN 4652-001:2014 (E) 14 5.2.4 Type 4 connectors C interfa

34、ce 5.2.4.1 Plug, 50 See Figure 7 and Table 7. Dimensions in millimetres Key 1 REF. Plane Figure 7 C plug interface Table 7 C plug dimensions Dimensions in millimetres A B C E F G H J K N min. 13,79 7,01 4,93 2,29 0,18 7,80 7,85 4,85 7,54 max. 13,94 2,34 1,27 8,56 6,38 7,72 P Q R S T U V W X Y min. 4

35、4,5 179,5 3,33 14,5 2,62 0,25 2,64 15,54 max. 19,84 11,18 45,5 180,5 3,58 15,5 2,87 0,41 2,90 prEN 4652-001:2014 (E) 15 5.2.4.2 Receptacle, 50 See Figure 8 and Table 8. Dimensions in millimetres Key 1 REF. Plane Figure 8 C receptacle interface Table 8 C receptacle dimensions Dimensions in millimetre

36、s A B C D E F G H J min. 14,99 13,46 12,32 11,18 10,44 3,02 max. 15,24 13,72 12,57 11,43 10,54 9,50 6,91 4,83 3,15 K L M N P Q R S T min. 8,43 7,80 2,24 7,62 179 6,93 12,57 max. 8,59 7,95 2,49 0,18 181 7,70 7,85 NOTE Clearance for mating connector coupling nut. prEN 4652-001:2014 (E) 16 5.2.5 Type 5

37、 connectors HN interface 5.2.5.1 Plug, 50 See Figure 9 and Table 9. Dimensions in millimetres Key 1 REF. Plane Figure 9 HN plug interface Table 9 HN plug dimensions Dimensions in millimetres A AA B D E F G H J L M P R T V W min. 19,30 1,60 9,10 9,33 0,13 3,50 3,05 7,34 2,54 6,69 10,24max. 23,50 14,5

38、0 1,68 9,85 0,38 3,35 1,48 NOTE Flared to meet electrical and mechanical performance. prEN 4652-001:2014 (E) 17 5.2.5.2 Receptacle, 50 See Figure 10 and Table 10. Dimensions in millimetres Key 1 REF. Plane Figure 10 HN receptacle interface Table 10 HN receptacle dimensions Dimensions in millimetres

39、A AB AK B C E F G K M R T U V W min. 16,80 9,02 13,92 14,50 8,33 14,99 1,96 13,11 9,12 max. 17,35 19,18 14,05 14,68 9,09 9,35 0,13 3,35 7,47 2,21 13,26 6,81 prEN 4652-001:2014 (E) 18 5.2.6 Type 6 connectors SMA interface 5.2.6.1 Plug, 50 See Figure 11 and Table 11. Dimensions in millimetres Key 1 RE

40、F. Plane Figure 11 SMA plug interface Table 11 SMA plug dimensions Dimensions in millimetres A Hex AA B D E F J L P Q T W min. 6,35 7,85 0,90 0,00 0,00 0,38 2,16 max. 8,00 4,59 0,94 0,25 0,25 2,54 0,38 3,43 4,18 1,14 prEN 4652-001:2014 (E) 19 5.2.6.2 Receptacle, 50 See Figure 12 and Table 12. Dimens

41、ions in millimetres Key 1 REF. Plane Figure 12 SMA receptacle Interface Table 12 SMA receptacle dimensions Dimensions in millimetres A AB B E F K M Q T U W min. 5,28 2,67 4,60 0,00 0,00 5,54 1,24 0,38 1,88 4,32 max. 5,49 0,25 0,25 1,29 4,18 1,14 1,98 NOTE Clearance for mating connector coupling nut.

42、 prEN 4652-001:2014 (E) 20 6 Test methods 6.1 List of tests See Table 13. Table 13 List of tests (1 of 3) EN 2591- Designation of the test Details 101 Visual examination Applicable 102 Examination of dimensions and mass Applicable 201 Contact resistance - low level Applicable (see product standard)

43、202 Contact resistance at rated current Applicable (see product standard) 203 Electrical continuity at microvolt level Not applicable 204 Discontinuity of contacts in the microsecond range Applicable 205 Housing (shell) electrical continuity Not applicable 206 Measurement of insulation resistance Ap

44、plicable (see product standard) 207 Voltage proof test Applicable (see product standard) 208 Temperature rise due to rated current Not applicable 209 Current temperature derating Not applicable 210 Electrical overload Not applicable 212 Surface transfer impedance Applicable (see product standard) 21

45、3 Shielding effectiveness from 100 MHz to 1 GHz Not applicable 214 Lightning strike, current and voltage pulse Applicable (see product standard) 216 Engagement depth of contacts Not applicable 221 Voltage Standing Wave Ratio (VSWR) Applicable (see product standard) 222 Insertion Loss (I.L.) Applicab

46、le (see product standard) 223 Measurement of characteristic impedance of a coaxial connector or contact Applicable (see product standard) 224 RF leakage Applicable (see product standard) 225 RF high potential withstanding voltage Applicable (see product standard) 226 Corona level Applicable (see pro

47、duct standard) 301 Endurance at temperature Not applicable 302 Climatic sequence Not applicable 303 Cold/low pressure and damp heat Applicable (see product standard) 304 Damp heat steady state Not applicable 305 Rapid change of temperature Applicable (see product standard) 306 Mould growth Applicabl

48、e (see 7.2.3) prEN 4652-001:2014 (E) 21 Table 13 List of tests (2 of 3) EN 2591- Designation of the test Details 307 Salt mist Applicable (see product standard) 308 Sand and dust Applicable (see product standard) 309 Dry heat Not applicable 310 Cold Not applicable 311 Low air pressure Applicable 312 Air leakage Not applicable 313 Ar