ASD-STAN PREN 4067-001-1997 Aerospace Series Connectors Electrical Circular Scoop-Proof Coupled by Threaded Ring Fire-Resistant Operating Temperature 260 Degrees C Peak Part 001 Te.pdf

《ASD-STAN PREN 4067-001-1997 Aerospace Series Connectors Electrical Circular Scoop-Proof Coupled by Threaded Ring Fire-Resistant Operating Temperature 260 Degrees C Peak Part 001 Te.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 4067-001-1997 Aerospace Series Connectors Electrical Circular Scoop-Proof Coupled by Threaded Ring Fire-Resistant Operating Temperature 260 Degrees C Peak Part 001 Te.pdf（39页珍藏版）》请在麦多课文档分享上搜索。

1、STD-AECMA PREN 40b7-001-ENGL I777 I LOL23LL 00L33b3 A21 W AECMA STANDARD NORME AECMA AECMA NORM prEN 4067-001 Edition P 1 September 1997 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledelle 94 - B-1200 BRUXELLES - Tel. (+32) 2 775 81 1 O - Fax. (+32) 2 775 81 11 ICs: Desc

2、riptors: ENGLISH VERSION Aerospace series Connectors, electrical, circular, scoop-proof, coupled by threaded ring, fire-resistant, operating temperature 260 OC peak Part O01 : Technical specification Srie arospatiale Luft- und Raumfahrt Connecteurs lectriques circulaires, contact protg, accouplement

3、 par bague filete, rsistant au feu, temprature 260 OC en pointe Partie O01 : Spcification technique Elektrische Rundsteckverbinder, Kontaktgeschtzt Schraubkupplung, feuerbestndig Betriebstemperaturen, 260 OC Spitze Teil 001 : Technische Lieferbedingungen This “Aerospace Series Prestandard has been d

4、rawn up under the responsibility of AECMA The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to th

5、e publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre NPS) and formal agreement of th

6、e Official Services of the Member countries it will be submitted as a draft European Standard to CEN European Committee for Standardization) for formal vote. Nota - Extra copies can be supplied by B.N.A.E. - Technopolis 54 - 199, rue Jean-Jacques Rousseau - 921 38 ISSY-LES-MOULINEAUX CEDEX I Comment

7、s should be sent within six months after the date of publication to I Edition approved for publication 1997-09-30 AECMA Gulledelle 94 B-1200 BRUXELLES C2 Chairman Mr Pezzetta aecma 1997 Page 2 prEN 4067-001 : 1997 Contents list O 1 2 3 4 10 11 12 Introduction Scope Normative references . Terminology

8、 Description Design . Definition drawings and masses Tests Quality assurance . Designation and marking . Delivery conditions Packaging Storage . Page 3 3 3 4 4 6 6 23 34 39 39 39 39 Page 3 prEN 4067-001: 1997 O Introduction This family of connectors is derived from MIL-C-83723 series III type T, EN

9、2997-001 and MIL-C-39029 for the contacts. It is particularly suitable for use on aircraft engines and in zones of severe environmental conditions on board aircraft, applying EN 2282. These connectors are distinguishable from EN 2997-001 by: - the contact protection effectiveness (scoop-proof). 1 Sc

10、ope This standard specifies the general characteristics, the conditions for qualification, acceptance and quality assurance, as well as the test programs and groups for threaded ring coupling circular connectors, fire-resistant, intended for use in a temperature range from - 65 OC to 260 OC peak. 2

11、Normative references This European Standard incorporates by dated or undated reference provisions from others publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revision

12、s of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. IS0 263 EN 2234 EN 2267-002 EN 2282 EN 2591 * EN 2997-001 EN 3042 EN 3155-001 EN 3197 EN 4067-002 IS

13、0 inch screw threads - General plan and selection for screws, bolts and nuts - Fiameter range 0,06 to 6 in Aerospace series - Fire-resistant electrical cables - Technical specification 1) Aerospace series - Cables, electrical, for general purpose - Operating temperatures between - 55 OC and 260 OC -

14、 Part 002: General 1) Aerospace series - Characteristics of aircraft electrical supplies Aerospace series - Elements of electrical and optical connection - Test methods - General Aerospace series - Connectors, electrical, circular, coupled by threaded ring, fire- resistant or non fire-resistant, ope

15、rating temperatures 175 OC continuous, 200 OC continuous, 260 OC peak - Part O01 : Technical specification Aerospace series - Quality assurance - EN aerospace products - Qualification procedure Aerospace series - Electrical contacts used in elements of connection - Part 001: Technical specification

16、1) Aerospace series - Installation of aircraft electrical and optical interconnection systems 1 Aerospace series - Connectors, electrical, circular, coupled by threaded ring, fire- resistant, operating temperature 260 OC peak - Part 002: Specification of performance and contact arrangements 1) * Inc

17、luding all its parts. 1) Published as AECMA Prestandard at the date of publication of this standard STD-AECMA PREN qOb7-00L-ENGL 1777 LOL23LL 00L33bb 530 D Page 4 prEN 4067-001: 1997 M IL-A-8243D M IL-C-25 769 J MIL-C-39029D MIL-C-83723E MIL-H-5606E MI L-L-7808 J M IL-L-7 8 70A MIL-L-23699C MIL-STD-

18、454M AS 1241A TR 4257 Anti-icing and deicing-defrosting fluids 2) Cleaning compound, aircraft surface, alkaline water base 2) Contacts, electrical connector, general specification for 2) Connectors, electrical, (circular, environment resisting), receptacles and plugs, general specification for 2) Hy

19、draulic fluid, petroleum base, aircraft, missile and ordnance 2) Lubricating oil, aircraft turbine engine, synthetic base, NATO code number 0-1 48 2) Lubricating oil, general purpose, low temperature 2) Lubricating oil, aircraft turbine engine, synthetic base 2) Electronic equipment, standard genera

20、l requirements for 2) Fire resistant phosphate ester hydraulic fluid for aircraft 3) Aerospace series - Elements of electrical and optical connection - Relationship between the numbering systems for parts of EN 2591 4) 3 Terminology See EN 2591. 4 Description Different housings and contact arrangeme

21、nts are provided according to the models depending on the service conditions. These connectors use crimp or solder contacts of sizes 20 and 16. The receptacles and plugs contain either male contacts or female contacts. The contacts fitted in the model YE receptacles are exclusively of the male solde

22、r type. The connectors are polarized by means of keyways and keys ; polarization shall be obtained before the male contacts enter the insert of the female contacts and before the coupling ring is engaged. The position of the keying arrangement is given in table 4. The visual check of coupling is obt

23、ained by masking of a blue colour band on the receptacle. 2) Published by: Department of Defense (DODI, the Pentagon, Washington, D.C. 20301 USA. 3) Published by: Society of Automotive Engineers, Inc. (SAE) 400 Commonwealth Drive, Warrendale, 4) Published as AECMA Technical Report at the date of pub

24、lication of this standard PA 15096-001 USA. STD-AECMA PREN 40b7-001-ENGL 1777 LOL231L DOL33b7 47-7 Page 5 prEN 4067-001 : 1997 4.1 Receptacle The receptacle may be attached by: - square flange; - nut, with sealing by O-ring at the attachment; - round soldered, brazed or welded flange for model YE co

25、nnectors. The receptacle contains five keyways in which the keys of the plug engage. The main keyway is fixed and is wider than the others. Polarization is ensured by the different positions which the secondary keyways may take. The position of the insert is fixed relative to the main keyway. 4.2 Pl

26、ug The plug contains five keys which engage in the keyways of the receptacle. The main key is wider than the others. Polarization is ensured by the different positions which the secondary keys may take. The position of the insert is fixed relative to the main key. The coupling ring permanently fitte

27、d on the plug enables the connectors to be coupled and uncoupled. The screwing up torque shall be lower than the unscrewing torque. The internal thread of the coupling ring may be treated with a suitable lubricant compatible with the performance required in this standard. The plug of model SE is fit

28、ted with a grounding spring device ensuring electrical continuity between the coupled connector housings. 4.3 Materials and surface treatment When dissimilar metals are in close contact, adequate protection against corrosion shall be used for the electromotive force of the cell not to exceed 0,25 V

29、(see EN 31971. 4.3.1 Housings The material of the housing for the connectors and for the fittings shall be passivated stainless steel (see EN 4067-002). 4.3.2 Contacts Unless otherwise specified, the contacts shall be in ferrous alloy for model YE and in copper alloy for the other models. They shall

30、 be gold-plated on an appropriate undercoat. Selective protection is authorized provided that it is sufficient to ensure that performance is met. Measurement of the thickness of the protective treatment shall be effected in accordance with EN 2591-508. 4.3.3 Nonmetallic materials The materials used

31、for insert, seals and grommets shall have a hardness and mechanical and electrical characteristics consistent with the required use. STD-AECMA PREN Ob7-00L-ENGL 1777 2012311 00133bB 303 Page 6 prEN 4067-001 : 1997 5 Design 5.1 Housings The connector housings shall be in one unit. They shall contain

32、teeth at the rear over the entire periphery and shall accomodate cable outlet accessories. The receptacle shall furthermore be fitted with an O-ring seal for sealing the coupled housings. Receptacles for attachment by nut shall contain an O-ring seal. The nut shall have holes for the passage of lock

33、ing wire. The threads shall conform to IS0 263. The coupling ring shall be designed so that the male and female contacts engage when it is turned in a clockwise direction and disengage when turned anticlockwise. The coupling threads may have a lubricant applied during manufacture. On completion of t

34、ightening of the coupling ring, mechanical contact shall exist between the receptacle and the plug. Masking of the colour band (see figure 1) shall show that the connectors are correctly coupled. The outlet accessories shall compress the grommet of the connectors without twisting it. A blue colour b

35、and indicating that the crimp contacts of the connectors are intended for rear removal shall be provided: - behind the flange of the receptacles with square flange; - on the flange of receptacles for nut attachment; - on the coupling ring of the plugs. The position of the colour bands shall be such

36、that at least one of them is visible when the connectors are fitted and when they are coupled or uncoupled. 5.2 Inserts The insert carrying the male and female contacts shall be in hard material and have a cross section and radii such that no cracks, flaking or breaks can occur in normal operation.

37、The insert for contacts shall be non-removable ; it shall be mechanically held in the housing. Sealing shall be provided between the housing and insert. The front face of the insert shall be such that sealing is ensured when the connectors are coupled. The interfacial seal of the insert of the male

38、contacts shall be bonded on the hard insert. The grommet shall permit sealing for all cable diameters indicated in EN 4067-002 and shall not be removable. The mechanical contacts retention system shall be integrated in the hard insert. The design of non-hermetic connectors shall permit individual in

39、stallation of the contacts without removal of the insert or grommet. Fitting and removal of the contacts shall be from the rear with the tools specified in the contact product standards. 6 Definition drawings and masses The general dimensions and the masses of receptacles and plugs are given in the

40、product standards. 6.1 Receptacle mating dimensions The mating dimensions of receptacles are shown in figure 1 and details A, B, C and D as well as in tables 1 and 2. Dimensions and tolerances are in millimetres. Detail A A Thread R 0.3* 0.1 Bluecolour band !I I I I I 1.73 11.13 Detail C 16.66 16,28

41、 interfacial $eat II / Optionalshape Hard insert Housing size 08 : 1,50 r0.08 - Sea dia. Housing sizes 10 to 24 : 1,78*0.08 16.98 Detail B 2,15 1.81 I I II 1 I 0.89 Detail D (5:l) 2,oo I90 )-L * Blue band shall be located on receptacle so as to be visible when unmated and fully covered when complete

42、ly mated. This colour band designs also the rear release contact connectors. Figure 1 STD-AECMA PREN 40b7-00L-ENGL 1777 D LOL23LL 0033370 TbL Page 8 prEN 4067-001 : 1997 Housing size 08 10 12 14 16 18 20 22 24 Table 1 Thread, C D 5 T class 2A 1) max. 7,37 9,86 12,58 1,93 12,45 1,80 16,28 16,15 20,60

43、 20,47 22,35 22,22 25,58 25,45 2,26 28,27 2,13 28,14 31,45 31,32 34,62 34,49 37,80 37,67 10,62 10,49 13,59 13,46 17,91 17,78 19,66 19,53 22,88 22,76 25,58 25,45 28,75 28,62 31,93 31,80 35,lO 34,97 0,562 UNEF 24 0,688 UNEF 24 14,17 15,93 19,61 0,875 UNEF 20 0,938 UNEF 20 1,062 UNEF 18 21,84 1,188 UNE

44、F 18 25,02 1,312 UNEF 18 28,19 1,438 UNEF 18 31,37 1,562 UNEF 18 1,50 1,24 2,06 1,80 20 16 I 1) IS0 263 3,OO 1,17 2,28 2,90 1 ,O7 2,14 3,81 1,75 2,88 3,71 1,65 2,73 Table 2 0.99 3,00 2,38 2,28 2,98 1,61 2,88 I 3f81 1 1,56 2,44 Page 9 prEN 4067-001 : 1997 6.2 Plug mating dimensions The coupling dimen

45、sions for plugs are shown in figure 2, in details A, B, C, as well as in tables 2 and 3. Dimensions and tolerances are in millimetres. 16.60 Thread A 5.75 Detail A 30“ k 2“ * blue colour band minimum width 0.64 Dosition oritional Detail B 5.00 Optional shape Hard insert %,I4 15,78 14,41 Front of 1.3

46、0 El 13.24 the contact 0.89 3,18 min. 8.26 Detail C 3.18 min. Grounding spring system * Blue band shall be located on receptacle so as to be visible when unmated and fully covered when completely mated. This colour band designs also the rear release contact connectors. Figure 2 STD-AECMA PREN qOb7-0

47、0L-ENGL 1777 101231L 0013372 834 Page 10 prEN 4067-001 : 1997 Housing size I A Thread, class 26 1 14 16 18 08 1 0,562 UNEF 24 0,938 UNEF 20 1,062 UNEF 18 I ,I 88 UNEF 18 10 I 0,688 UNEF 24 26f04 25,02 2921 32r38 28,19 31,37 12 I 0,875 UNEF 20 28,52 33,a8 26,57 41,91 28,40 3170 37,06 29,74 44,07 31,5

48、7 3487 40,23 32,91 47,24 34,75 20 1 1,312 UNEF 18 1,438 UNEF 18 1,562 UNEF 18 1) IS0 263 Table 3 B 1 J K H M max. 1 min. 1 I min. 1 min. I max. t Page 11 prEN 4067-001: 1997 6.3 Receptacle and plug polarization See figure 3 and tables 4 and 5. Dimensions and tolerances are in millimetres. Receptacle

49、 Plug Figure 3 STD-AECMA PREN iOb7-001-ENGL 1977 R 1012311 003337q b07 R Page 12 prEN 4067-001 : 1997 Table 4 Polarization Housing size Table 5 1 HIJI 1,40 1,24 5,72 5,64 7,24 7,16 9,40 9,32 10,29 10,21 11,89 11,81 13,23 13,15 14,81 14,73 16,41 16,33 17,98 2,47 2,31 3,26 3,10 1,96 i .a3 9,47 10,49 1 I 11,96 12t09 I :i: 15,01 I 14,88 16,61 1 16,48 18,19 1 18,06 i STDmAECMA PREN LIOb7-001-ENGL 1997 m LO123L3 0033375 543 m Page 13 prEN 4067-001 : 1997 Housing size 08 10 12 6.4 The dimensions of the rear part of receptacles and plugs with threads for mounti