ASD-STAN PREN 3545-005-2013 Aerospace series Connectors electrical rectangular with sealed and non-sealed rear plastic housing locking device operating temperatures 55 to 175 Part .pdf

《ASD-STAN PREN 3545-005-2013 Aerospace series Connectors electrical rectangular with sealed and non-sealed rear plastic housing locking device operating temperatures 55 to 175 Part .pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 3545-005-2013 Aerospace series Connectors electrical rectangular with sealed and non-sealed rear plastic housing locking device operating temperatures 55 to 175 Part .pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 3545-005 Edition P 2 December 2013 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: 49.060 Supersedes edition P

2、 1 of April 1995 and will supersede EN 3545-005:2006Descriptors: ENGLISH VERSION Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 005: Female coding and attachment system for mounting on

3、free housing (plug) Product standard Srie arospatiale Connecteurs lectriques, rectangulaires, tanches et non tanches larrire, botier en plastique, verrouillage, tempratures dutilisation 55 C 175 C Partie 005 : Systme de fixation et de codage femelle pour montage sur botier mobile (fiche) Norme de pr

4、oduit Luft- und Raumfahrt Elektrische Rechtecksteckverbinder mit und ohne hintere Abdichtung, Plastikgehuse, Verriegelungssystem, Betriebstemperaturen von 55 C bis 175 C Teil 005: Buchsenkodierung und Befestigungszubehr fr freie Steckverbinder Produktnorm This “Aerospace Series“ Prestandard has been

5、 drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subseque

6、nt to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted

7、as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any na

8、tional standards conflicting with the EN. Edition approved for publication 1st December 2013 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2013 by ASD-STAN prEN 3545-005:2013 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative refere

9、nces 3 3 Terms and definitions . 3 4 Required characteristics . 3 4.1 Dimensions, mass . 3 4.2 Material, surface treatment . 5 4.3 Main general characteristics 5 5 Designation 5 6 Technical specification . 6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electri

10、cal Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3545-005:2013 (E) 3 1 Scope This standard specifies the female coding and attachment system for mounting o

11、n free housing in the family of rectangular electrical connectors with sealed and non-sealed rear, plastic housing, locking device, for operating temperatures from 55 C to 175 C. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are

12、indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3545-001, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plast

13、ic housing, locking device, operating temperatures 55 C to 175 C Part 1: Technical specification EN 3545-002, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 2: Specification of performa

14、nce and contact arrangements FED-STD-H28/2A:1978, Screw thread standards for federal services 1)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3545-001 apply. 4 Required characteristics 4.1 Dimensions, mass The dimensions of attachment system are giv

15、en in Figure 1. Dimensions and tolerances are in millimetres. Mass: 3 g max. 1) DoD National (US) Mil. Department of Defense http:/www.defenselink.mil/ prEN 3545-005:2013 (E) 4 Key 1 Optional knurling 2 Washer M 2,5 3 0.1120 inch - 40 UNC-3A according to FED-STD-H28 4 Captive screw 5 6 recessed flat

16、s 2,3800,066 Female body 7 Retaining ring 8 5,4000,05(groove) 9 0,3 to 0,4 at 30 10 6 flats 8,00,100,0511 Position indicator (recessed line) 12 0.1120 inch - 40 UNC-3B according to FED-STD-H28 Figure 1 Female coding and attachment system prEN 3545-005:2013 (E) 5 0,025 General concentricity View on F

17、 Retaining ring Detail X Figure 2 Retaining ring 4.2 Material, surface treatment Body: steel, cadmium-plated, dichromate sealed Retaining ring: beryllium copper, cadmium-plated, dichromate sealed 4.3 Main general characteristics See EN 3545-002. Tightening torque of the locking screw: 0,06 daNm to 0

18、,10 daNm 5 Designation EXAMPLE Description block CONNECTOR, CODING SYSTEM Identity block EN3545-005A Number of this standard A: female attachment system for mounting an free housing (plug) NOTE lf necessary, the code I9005 shall be placed between the description block and the identity block. prEN 3545-005:2013 (E) 6 6 Technical specification See EN 3545-001.