ARMY PPP-D-705 E-1994 DRUM SHIPPING AND STORAGE STEEL 16 AND 30 GALLON CAPACITY《容量为16加仑和30加仑的储运钢桶》.pdf

《ARMY PPP-D-705 E-1994 DRUM SHIPPING AND STORAGE STEEL 16 AND 30 GALLON CAPACITY《容量为16加仑和30加仑的储运钢桶》.pdf》由会员分享，可在线阅读，更多相关《ARMY PPP-D-705 E-1994 DRUM SHIPPING AND STORAGE STEEL 16 AND 30 GALLON CAPACITY《容量为16加仑和30加仑的储运钢桶》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、a O a PPP-D-705E January 3, 1994 SUPERSEDING PPP-D-7 05D August 24, 1974 FEDERAL SPECIFICATION DRM, SHIPPING AND SIDRAGE: STEEL, 16 AND 30 GALLON CAPACITY This specification was approved by the Cannissioner, Federal Supply Service, General Services Zkhinistration, for the use of all Federal agencies

2、. 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers new straight sided, cylindrical- stel drums of 16 gallon, 30 gallon, and 120 pound grease capacities. 1.2 Classification. 1.2.1 Tvpes. The drums covered by this specification shall be of the following types, as specified (see table I

3、 and 6.2): Type1 - 30 gallon drum, double seamed chimes, Type 11 - 16 gallon drum, double seamed chimes, Type III tight head (MH2.6) tight head (MH2.7) double seamed bottom chime, full removable lug cover (MH2.8) bottom chime, full removable head (MH2.12) - 120 pound grease - Rule 40 or Item 260 dru

4、m, Type IV - 30 gallon - Rule 40 or Item 260 drum, double seamed Beneficial camients (recamiendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: Center, Natick, MA Improvement Proposal (W Form 1426) appearing at the end of this

5、document or by letter. U.S. Army Natick Research, Developnent, and Engineering 01760-5019 by using the Standardization Dccument AMSC N/A FSC 8110 DISIRIBUTION STATEMENT A. Approved for public release; distrihtion is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted with

6、out license from IHS-,-,- PPP-D-705E 9999974 OLb3065 OT4 PPP-D-705E Typev - 30 gallon drum, double seamed bottom chime, full removable head (MH2.13) Type VI - 16 gallon - Rule 40 or Item 260 drum, double seamed bottom chime, full removable head (MH2.14) 2. APPLICABLE 2.1 Government documents. The fo

7、llowing documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this document to the extent specified herein: Federal Specifications: TT-E-485 - Enamel, Semi-Gloss, Rust-Inhibiting W-L- 8 O O - Lubricating Oil, General Purpose, Preservative, (Water-Di

8、splacing, ILW Temperature) PPP-P-420 - Plugs and Flanges (For Drum Closures) Federal Standards: FED-STD-123 - Marking for Shipnent (Civil Agencies) FED-SID- 14 1 - Paint, Varnish, Lacquer and Related Ma-erials: FED-STD-595 - Colors Methods of Inspection, Sampling and Testing (Activities outside the

9、Federal Government may obtain copies of Federal specifications, standards, and Cmrcial Item Descriptions as outlined under General Information in the Index of Federal Specifications, Standards, and Comercial Item Descriptions. supplements as issued, is for sale on a subscription basis by the Superin

10、tendent of Documents, U.S. Government Printing Office, Washington, Dc 20402. ) (Single copies of this specification, and other Federal specifications and The Index, which includes cumulative monthly Comnercial Item Descriptions required by activities outside the Federal Government for bidding purpos

11、es are available without charge from the General Services Pdministration Wisiness Service Centers in Boston, MA; New York, NY; Philadelphia, PA; Washington, Dc; Atlanta, GA; Chicago, IL; Kansas City, BD; Fort Worth, TX; Houston, TX; Denver, CO; San Francisco, CA; Los Angeles, CA; and Seattle, WA.) (

12、Federal Government activities may obtain copies of Federal Standard- ization documents and the Index of Federal Specifications, Standards, and Comercial Item Descriptions from established distribution pints in their agencies.) Military Specification: MIL-G-432 - Gaskets, Nonmetallic, Synthetic RuWer

13、 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- PPP-D-705E i 979974 0163066 T30 i PPP-D-7 05E Military Standards: MIL-105 - Sampling Procedures and Tables for Inspection MIL-STD-129 . - Marking for Shiprent and Storage by Attributes (Copies of mi

14、litary specifications and standards required by contractors in connection with specific procurattent functions should be obtained fran the procuring activity or as directed by the contracting officer.) LAWS AND REGuw1TIONS 49 CFR 100-199 - Department of Transportation Rules and Regulations Covering

15、Hazardous Materials (The code of Federal Regulations (CFR) and the Federal Register (FR) are for sale on a subscription basis by the Superintendent of Eocuments, U.S. Government Printing Office, Washington, DC 20402. When indicated, reprints of certain regulations may be obtained fran the Federal ag

16、ency responsible for the issuance thereof.) 2.2 Other publications. The following documents form a part of this document to the extent specified herein. identified, the issue in effect on date of invitation for bids or request for proposal shall apply: Unless a specific issue is AMERICAN NATIONAL ST

17、ANDARDS INSTIm (ANSI) MH2.6 ANSI Standard for 30 Gallon Tight-Head Universal Druras O MH2.7 ANSI Standard for 16 Gallon Tight-Head Universal Drum MH2.8 ANSI Standard for 16 Gallon Full-Removable-Head Lug-Cover Universal Drums (LEC-Rule 40, NMFC - ITEM 260) MH2.12 ANSI Standard for 30 Gallon Full-Rem

18、ovable-Head Universal Drurrr; (LEC Rule 40, NMFC - ITEM 260) MH2.13 ANSI Standard for 30 Gallon Full-Removable-Head Universal Drum MH2.14 ANSI Standard for 16 Gallon Full-Removable-Head Universal Drums (LEC - Rule 40, NMFC - ITEM 260) (Application for copies should be addressed to the American Natio

19、nal Standards Institute, 11 West 42nd Street, New York, NY 10036.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ - PPP-D-705E M 9999974 OLb30b7 977 W PPP-D-705E AMERICAN SOCI FOR TESTING AND MATERIALS (AsIM) ASITv D 3951 - Packaging, Cormiercia

20、l ASTM D 4919 - Testing for Hazardous Materials (Application for copies should be addressed to the American Society for Testing and Materials, 1916,Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare o

21、r distribute the documents. documents also may be available in or through libraries or other informational services.) These 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in th

22、is document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQuIREMENIyj 3.1 Material. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. 3.1.1 Steel sheet and strip, fitti

23、nqs, and seaminq ccmmund. Steel sheet and strip, fittings, and seaming compound shall be in accordance with the requirements of 49 CFR 178, Subpart L or ANSI MH2 Standard. tolerances shall be in accordance with the applicable MH2 Standard. Thickness of steel sheet shall be measured at any point on t

24、he sheet not less than 3/8 inch from the edge. Steel sheet 3.1.2 Gasket. Gaskets shall be in accordance with MIL-G-432. 3.1.3 Paint. The pint shall conform to TT-E-485 and shall be color No. 27037, 27040, or 24087 of FED-STD-595, as specified (see 6.2). 3.1.4 Pluqs and flanqes. Plugs and flanges sha

25、ll be in accordance with PPP-P-420. 3.1.5 Cap seals. Cap seals shall be those camnercially available for hand When specified (see 6.2), the tool application and fit the closure supplied. color shall be the same as the drum. 3.2 Desiqn and construction. Type I, II, III, IV, V, and VI drurits shall be

26、 in accordance with ANSI Standards MH2.6, MH2.7, MH2.8, MH2.12, MH2.13, and MH2.14, respectively. Type I, II, and V drums shall be in accordance with 49 CFR 178, as applicable. Steel gages shall be as specified in table I. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted withou

27、t license from IHS-,-,-PPP-D-705E U.S. Manufacturers Standard Gage Closing Type Carrier ANSI Heads Covers i3ottaw Bodies ring - MH2.6 19 19 19 II MH2.7 20 20 20 I 2/ III i/ Rule 40 MH2.8 20 20 20 IV A/ Rule 40 MH2.12 19 19 19 16 V MH2.13 18 18 18 12 20 20 . 20 16 VI i/ Rule 40 MH2.14 - - - - - - - 3

28、/ Item 260 - - Item 260 - i/ Uniform Freight Classification Rule and National Motor Freight Item. - 2/ When specified (see 6.2), 20 gage. - 3/ When specified (see 6.2), 22 gage (for greases only.). (24 gage for intrastate only in California). 3.3 Dimensions and capacity. Dimensions, capacity, tare w

29、eight, and tolerances shall be in accordance with the applicable ANSI Standani (see 6.3). In addition, type III drums shall be designed to accomnodate 120 pounds of light grade grease. determined as specified in 4.3.3. The rated or nominal capacity shall be 3.4 Lininq. Drums used to package material

30、s which would have a deleterious effect on bare drum metal, or vice versa, shall be lined on all internal surfaces with a material that will neither affect nor be affected by the material packaged. A lining material mting these requirements shall be agrd upon by the contracting officer and supplier.

31、 canpliance of material(s) specified herein shall be provided to the contracting officer (see 4.1.2 and 6.2). A certificate of 3.5 Foq spray. threaded flanges, if unplated or uncoated, shall be fog sprayed. IV, arid V drums shall be sprayed with 11 cubic centimeters to 14 cubic centimeters (cc) of o

32、il conforming to W-L-800. Types II, III, and VI drums shall be sprayed with 6 cc to 8 cc of oil. Dispensing shall be through an accurate metering device. all fabrication operations have been completed, including painting, but before final insertion of plugs or applying of removable head or cover for

33、 shiprent. The interior surfaces shall be completely wetted with the oil when the fog has settled. There shall be no surplus oil collecting in pools or rings on the bottom. Fog spray shall be applied after drums have cooled to a The interior surfaces of the drum and the gasket seats of Types I, Spra

34、ying shall be acccmplished irmiediately after 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- - _ PPP-D-705E 9999974 03630b9 74T = PPP-D-705E temperature beluw 140*. Air lines of fogging equipent shall contain misture traps to prevent introducin

35、g water vapor into the drums. plugs shall be inserted, wrench tight, imnediately after fog spray. Removable head or removable cover drum shall have the head, or cover, fogged before attaching to the drum. Closure 3.5.1 Unlined drums for materials susceptible to contamination. Unlined drums to be use

36、d for products required to be of extremely high purity (i.e., super clean products) shall not have fog spray as specified in 3.5, or other surface treatmnt at time of filling. thoroughly washed and rinsed prior to use. Drums used for such material will be 3.6 Closures. Closure shall be in accordance

37、 with 49 CFR and ANSI MH2 Standard. not move when tested as specified in 4.3.2. be provided for each bung of type I and II drums. cellular, rubber, flawed-in or sponge rubber gasket shall be provided with each removable cover of types III, IV, V, and VI drums. Type III drums shall have the cover lug

38、s crimped around and under the false wire or ;ur1 when closed. lever-lock type closing ring. locking ring having forged lugs, one of which shall be threaded, and have a 3/8 inch minimum bolt and locking nut. The vent and bung closure flanges for type I and II drums shall Gaskets specified in 3.1.2 s

39、hall A tubular, synthetic, The types IV and VI drums shall be provided with a bolted or The type V drum shall be provided with a 3.6.1 Cap seals. II drums shall have cap seals applied that prevent removing the plug without destroying the seal. The seal shall be so constructed that the seals may be a

40、pplied by hand tools. supplied. The cap seals shall pass the air test specified in 4.3.6, without leakage. When specified (see 6.2), each closure for types I and The cap seals shall be suitable for the closures 3.7 Finish. 3.7.1 Cleaninq. Prior to painting, the interior and exterior of the drums sha

41、ll be free of rust, loose scale, metal particles, foreign matter, and oily and greasy substances. Sharp edges and metal splinters shall be removed. 3.7.2 Painting. The surface that will be the drum exterior shall be coated with paint specified in 3.1.3. shall, after welding, have the unpainted side

42、seam painted. Ail closure plugs shall be in place during final painting operations. to the dnim and curing, the enamel shall show good adhesion, shall be difficult to furruw, and shall not flake off or Shaw jagged edges when subjected to the knife test specified in 4.3.4. shall be properly dried or

43、baked, as specified, and have a dried film thickness of not less than 0.8 mil, when tested as specified in 4.3.5. Drums which were coated in the flat After application The coating on all surfaces 3.8 Performance resuirements. Types I, II, and V drums. shall be subjected to performance oriented packa

44、ging (POP) tests cited in 49 CFR 178, Subpart M. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PPP-D-705E 9999974 0363070 461 PPP-D-705E Unless otherwise specified in Rule 40 or Item 260, type III, IV and VI drums are not required to pass POP tes

45、ting. 3.9 Identification markinq. Marking of drums shall be in accordance with 49 CFR 178, Subpart L, for the material to be carried or applicable Rule 40 or Item 260. shall be embossed with “US“. The “US“ may be omitted when drums are procured incident to procurement of the product contained therei

46、n. (see 6.2), containers shall be marked on the lmer one third of the side wall in letters at least 1/4 inch in height as follows: When qty drums are procured by the Government, each drum When specified Container Conforms to PPP-D-705, Type . 3.10 WorlaMnship. Finished drums shall be clean, free fro

47、m rust, loose slag, or leaks. Components and linings, when required, shall be free from defects of application that make them leak or may contaminate the product being packed. fusion. Solder shall not be used to repair leaks. There shall be no excess seaming compound on either the inside or outside

48、of the drum. be adherent, free of blisters, imbedded foreign matter, or crinkles. Threaded areas shall not have threads missing, stripped, or fractured. The tm ends of the bolt ring shall be at least 1/4 inch apart when the ring is tightened to close and seal the drum. when the drum is filled and cl

49、osed. Welds shall be free of burrs, splatter, cracks, or incomplete Spot wlds, if used, shall be free from flash or bum through. Painted surfaces shall There shall be no evidence of leaking Markings shall be complete and legible. 4. QUATITY ASSURANCE PEaoVISIoNS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or pchase order, the contractor is responsible for the performance of all inspection requirements (examinatio