ARMY PPP-C-96 E-1992 CANS METAL 28 GAGE AND LIGHTER [Use In Lieu Of ARMY PPP-C-0096 C]《28号及更小的金属罐[代替 ARMY PPP-C-0096 C]》.pdf

《ARMY PPP-C-96 E-1992 CANS METAL 28 GAGE AND LIGHTER [Use In Lieu Of ARMY PPP-C-0096 C]《28号及更小的金属罐[代替 ARMY PPP-C-0096 C]》.pdf》由会员分享，可在线阅读，更多相关《ARMY PPP-C-96 E-1992 CANS METAL 28 GAGE AND LIGHTER [Use In Lieu Of ARMY PPP-C-0096 C]《28号及更小的金属罐[代替 ARMY PPP-C-0096 C]》.pdf（55页珍藏版）》请在麦多课文档分享上搜索。

1、PPP-C-SbE m 9999974 0324843 302 m PPP-C-96E Decmber 31. 1992 SUPERSEDING Fed. Spec. PPP-C-96D March 10, 1972 and -nt 3, Aug. 20 1976 and Mil Spec. MIL-L-43762 Decmber 9, 1977 FEDERAL SPECIFICATIOGJ lhe General Services Administration has authorized the use of this federal specification, for all Fede

2、ral Agencies. 1. =PE AND CL?SSIFICATIW 1.1 Same. This specification and appendix thereto cover the requirements for new metal cans made of 28 gage and lighter sheet metal plate, and DUJ! 2P and 2Q metal containers suitable for packaging and packing it- for shipent and storage and the packaging, pack

3、ing, and marking of the filled cans. Also rec.losure plastic lids. 1.2 Classification. 1.2.1 -Cans. The cans shall be of the follawing types and shapes, as specified (see 6.1). Closures shall be of the follawing classes, as spscified (see 6.1). distribution is unlimited. Provided by IHSNot for Resal

4、eNo reproduction or networking permitted without license from IHS-,-,-PPP-C-9bE 9999974 0324842 049 m PPP-C-96E Type II - Round, soldered side and end seam, soldered vent hole closure (see 3.3.2 and 6.7) reclosure feature (see 3.3.3) III - Round, opn-top, double-seamed ends, key-opening band, with T

5、ype IV - Round, oval or oblong one piece drawn body, open-top with crinped, soldered, double-seamed, lid, or lid crimped in position by means of an annular band with tear tab, or slip cover lid (see 3.3.4) Class 1 - Key-opening (see 3.3.4.1) Class 2 - Hand-opening (see 3.3.4.2) Class 3 - Slip cover

6、(see 3.3.4.3) Type V - Round, square, oval, or oblong, both ends double-seamed on (see 3.3.5) Class 1 - With single friction plug (see 3.3.5.1) Class 2 - With mltiple friction plug (see 3.3.5.2) Class 3 - With Neman seal (see 3.3.5.3) Class 4 - With screw cap (see 3.3.5.4) Class 5 - With snap-on (ty

7、pe which is opened by downward pressure in the center) cap (see 3.3.5.5) Class 6 - With rigid spout closure (see 3.3.5.6) Class 7 - With other closures (see 3.3.5.7) Class 8 - With flexible spout closure (see 3.3.5.8) Class 9 - With press-in closure with plastic Wh-pull spout (see 3.3.5.9) Type VI -

8、 Round, square, or oblong - bottom, end crimped or double-seamed on, with full friction plug, slip cover or hinged closure (see 3.3.6) Type VI1 - Round, flaring bcdy (see 3.3.7) Class 1 - Bottan end crimped or double-seamed on, with full friction Class 2 - Open-top, key-opening, both ends double-sea

9、med on, top end plug or slip cover closure (see 3.3.7.1) fitted with crown or screw cap closure (see 3.3.7.2) end fitted with crown or screw cap closure (see 3.3.8) Type VI11 - Round, dane or cone top, both ends double-seamed on, top Type Ix - pressurized cans (see 3.3.9) Class 1 - Roud can, soldere

10、d or welded side seam, double-seared Class 2 - Round can, soldered or welded side seam, double-seamxi concave top and bottan (see 3.3.9.1) concave bottom, double-sean Coatings, Exterior, For Tinned Food Cans Enanrel, Alkyd, semigloss Inw M3c Content Primer Coating, Alkyd, Corrosion Inhibiting, Lead

11、Boxes, Wood-Cleated Panelboard Boxes, Wood, Nailed and Ibck-Corner Boxes, Shipping, Fiberboard Type v, Class 4) General Specification For and ChrOlMte Free, KC Carpliant Boxes, wood, Cleated-PlyMOod Federal Standards: FED-SID-101 - FED-SIP123 - FED-SrD-595 - Preservation, Packaging, and Packing Mate

12、rials; Marking for Darrestic Shipnent (Civil Agencies) Color Wt procedures (Activities outside the Federal Goverment may obtain copies of Federal specifications, standards, and comercial item descriptions as outlined under General Information in the Index of Federal Specifications, Standards and Car

13、mercial Item Descriptions. The Index, which includes cumulative bimnthly supplements as issued, is for sale on a subscription basis by the Superinten- dent of Documents, U.S. Goverment Printing Office, Washington, DC 20402.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted with

14、out license from IHS-,-,-PPP-C-9bE 9999974 0324844 911 PPP-C-96E (Single copies of this specification, and other Federal specifications and carmercial item descriptions required by activities outside the Federal Goverrnnent for bidding puposes are available without charge fran General Services Adnin

15、istration Business Service Centers in Boston, MA; New York, NY; Philadelphia, PA; Washington, Dc; Atlanta, a; Chicago, IL; Kansas City, MD; Fort Worth, Tx; Houston, TX; Denver, CD; San Francisco, CA; IDS Angeles, CA; and Seattle, WA.) (Federal Govenment activities may abtain copies of Federal standa

16、rdization documents and the Index of Federal specifications, standards and Camrarcial Item Descriptions fran established distribution points in their agencies.) Militarv Suecif ications : MIL-E-52891 - EMmel, Lusterless, Zinc Phosphate Styrenated MW lLpe Militam Standards: MIL-ml05 - Sarrpling Pmced

17、ures and Tables for Inspection MIL-Sm-129 - Marking for Shipent and Storage by Attributes (Copies of Military specifications and standards required by contractom in connection with specific procurement functions should be obtained fmn the procuring activity or as directed by the contracting officer.

18、 ) 2.1.1 Other Goverment documents, drawirms, and Dublications. Tple following other Govennnent mts, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. Federal L

19、aws and Elations UNITED STATES WE Congressional and Zkhinistrative News. public Iaw 94-580 - Resoume Conservation and Recowry Act of 1976. U.S. Department of Health and Mmran services Federal Food, Drug, and Cosnetic Act anb regulations pramlgated theremler (21 CFR Parts 1-199). wt of Transportation

20、 Rules and Regulations Part 178 Subpart B specification 2P and 2Q or 49cFR. (lapies of the Code and Acts may be obtained fmn the Superintendent of Documents, U.S. Goverrnnent Printing Office, Washington, DC 20402-0001.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without l

21、icense from IHS-,-,-PPP-C-9bE m 9999974 0324845 858 m PPP-C-96E 2.2 Other rxblications. Ihe following documnts form a part of this specification to the extent specified herein. Unless a specific issue is identified, the issue in effect on or a lid crimped in position by means of an annular band, or

22、slip cover lid. Methods of opening for type IV cans shall be one of the follcwing classes. 3.3.4.1 Class 1. Type IV, class 1 cans shall be furnished with a scored annular band to facilitate opening by mans of metal key or another appropriate device. A corrosion-resistant metal key shall be furnished

23、 with and attached to one end of each can designed for key-opening (see figures 4 and 5). 3.3.4.2 Class 2. Type N, class 2 cans shall be furnished with a top suitably scored to provide a tear strip with a hand or finger grip affixed to one erd of the tear strip (see figures 2 and 5). 3.3.4.3 Class 3

24、. Type IV, class 3 cans shall be furnished with a slip cover lid as specified in 3.4.8 (see figure 6). 3.3.4.4 Plastic, reclosure lids. When specified (see 6.1), type IV, class 1 or 2 cans shall have a close-fitting plastic lid affixed securely to one end of the can. The plastic lids shall confonn t

25、o the requirements specified in .3.1.5 and 3.3.1.2.1.1. 3.3.5 “me V. Type V cans shall be round, square, oval, or oblong. Both ends shall be carrpound-lined double-seamed in position. Closures for type V cans shall be one of the following classes. 3.3.5.1 Class 1. Type V, class 1 cans shall be fitte

26、d with a single friction plug closure (see 3.4.1 and figure 7). When specified (see 6.1), both ends of type V, class 1 containers shall be double-seamed to the body with a dry seam (no caymund). When specified (see 6.1) , an opening lever dev.ice (see 6.4) shall be provided for opening the friction

27、plug closure. 3.3.5.2 Class 2. Type V, class 2 cans shall be fitted with a mltiple friction plug closure (see 3.4.1 and figure 8). 3.3.5.3 Class 3. Tvpe V, class 3 cans shall be fitted with a Neman seal closure (see 3.4.2 and figure 9). 3.3.5.4 Class 4. TJpe V, class 4 cans shall be fitted with a sc

28、rew cap closure as specified in A-A-888 and shown on figure 10. 3.3.5.5 Class 5. Type V, class 5 cans shall be fitted with a snap-on clocjure (see 3.4.4 and figure 11). 3.3.5.6 Class 6. Type V, class 6 cans shall be fitted with a rigid spout closure (see 3.4.5.1 and fiqms 12). 9 Provided by IHSNot f

29、or ResaleNo reproduction or networking permitted without license from IHS-,-,-PPP-C-96E 3.3.5.7 Class 7. Type V, class 7 cans shall be fitted with a cork seal or special lever type or quarter tun? (bayonet-lock) type closure, as specified (see 3.4.6, 3.4.7 and 6.1). 3.3.5.8 Class 8. Type V, class 8

30、cans shall be fitted with a flexible spout closure (see 3.4.5.2 and figures 13 and 14). 3.3.5.9 Class 9. Type V, class 9 cans shall be fitted with a press-in closure (see 3.4.5.3 and figure 15). 3.3.6 Twe VI. Type VI cans shall be round, square, or oblong in shape (see 1.2). The can bottan shall be

31、carrpound-lined, double-seamed, or crimped in position, or, when specified (see 6.1) , shall be dry (no canpound) , double-seamed in position. The can shall be fitted with a full friction plug, slip cover, or hinged lid closure (see 3.4.1, 3.4.8, 3.4.10 and figures 16 and 17). 3.3.7 Twe VII. Tvpe VI

32、1 cans shall be round and have a flaring body. 3.3.7.1 Class 1. Type VII, class 1 cans shall be canpound-lined, double-seamed, or crimped bottan end. Cans shall be fitted with full fric%ion plugs or slip cover closures (see 3.4.1, 3.4.8 and figure 18). 3.3.8 Tvpe VIII. Type VI11 cans shall be round

33、with compound-lined, double“ ends. One end of the can shall be dame-shaped or conical top and fitted with a screw cap or cm cap closure (see 3.4.3, 3.4.9 and figlre 20). 3.3.9 vpe IX. Pressurized cans shall be one of the following classes. ChjS 1, 2, and 3 cans shall not leak when tested as specifie

34、d in 4.4.4. 3.3.9.1 Class 1. Type IX, class 1 cans shall be round shaped, concave top and bottan, having a valve opening dieter to fit the type of valve specified (see 6.1), with an outside welded side seam. Alternatively, the side seams may be soldered leaving a plain solder margin. The ends shall

35、be compund-lined and double-seamed to the body. Unless otherwise specified (see 6.1) , class 1 cans shall be furnished without pmtective caps (see figure 21). 3.3.9.2 Class 2. Type U, class 2 cans shall be muxi shaped, rounded dm? top, concave bottcm, and with an outside welded side seam. Altern- at

36、ively, the side seams may be soldered leaving a plain solder margin. The ends shall be ccqound-lined and double-seamed to the body. Cans shall be fitted with a 1 inch diameter valve and provided with metal or plastic caps to protect the valve (see figure 21). 10 Provided by IHSNot for ResaleNo repro

37、duction or networking permitted without license from IHS-,-,-PPP-C-SbE m 9999974 Ol12485L 051 m PPP-C-96E 3.3.9.3 Class 3. Typ IX, class 3 cans shall be h, drawn, seamless bodies and dornes, with a 1 inch diameter opening and concave bottan. The bottan shall be carrpourld-lined and double-sd to the

38、body. Cans shall be fitted with a 1 inch diameter valve and provided with metal or plastic cap to protect the valve (see figure 21). 3.3.9.4 Class 4. Type IX, class 4 (WI“2P) container shall be seamless, or with seams, welded, soldered, brazed, double-seamed, or swedged. The containers shall met the

39、 requirements of -2P when tested in accodance with 4.4.4.1. 3.3.9.5 Class 5. Type IX, class 5 (Dar-2Q) container shall be seamless, or with searns, welded, soldered, brazed, cEouble-seamed, or wedged. The containers shall met the requirenents of -2Q when tested in accordance with 4.4.4.1. .4 Closure

40、s. Closures shall be one of the folluwing, as specified (see )* 3 6.1 3 the .4.1 Friction lua as. miction plug closures shall be fabricated of S- normal coating weight material as that used in the body of the container. Unless otherwise specified (see 6.1), friction plugs shall be of the regular mlt

41、iple friction plug type (see figure 8). When specified (see 6.1), friction plugs shall be: single friction plug (see figure 7) or raised multiple friction plug (see figure 8); or full friction plug type (see figure 16) . 3.4.2 Newman seal. The Newman seal shall be fabricated from tinplate having the

42、 same naninal coating as that specified for the ends of the can. The seal shall be canpound-lined and designed to be crimped over the neck which is drawn in the top end of the can so that the final seal is leak-proof (see figure 9). 3.4.3 %maw. The cap and neck of the closure shall be fabricated fru

43、n tinplate having a nomirml tin coating weight of 0.50 pound or greater, or, when applicable (see 6.2), tinplate specified in 3.1.1.2. They shall have a min.imrm of a 1-1/2 rolled threads, The neck shall be soldered or crimped to the top of the container, or formed in a drawing operation. The top po

44、rtion of rhe periphery of the cap shall be knurled to permit mval. Each cap shall be provided with a liner pad and facing. The facing shall be made of material that will provide a leakproof seal (see figure 10). When specified (see 6.1), leakpmf plastic screwcaps shall be used. The screwcap and can

45、neck openings shall be canpatible. The openings shall be one of the follwing applicable outside diameters as specified (see 6.1). When the opening size is not specified in the contract or order, it shall be the option of the supplier. 11 Provided by IHSNot for ResaleNo reproduction or networking per

46、mitted without license from IHS-,-,-PPP-C-9bE m 9999974 0124852 T98 m PPP-C-96E can volume Outside Thread Diameter (Inches) Waninall 1 Pt* 1 st* 1/2 gal. 1 gal. 2 gal. 5 gal. 1, 1-1/4 1, 1-1/4 1, 1-1/4 1, 1-1/8, 1-1/4, 1-3/4, 2-7/0 1-1/4, 1-1/2, 1-3/4 1-3/4, 2-7/0 3.4.4 Snapon-cap. Snapon closures,

47、which a.re remwed by dowrrward pressure in the center, shall be fabricated fran tinplate having a minimum ndnal tin coating weight of 0.50 pounds or when applicable (see 6.2), tin free steel of minhm 128 pound base weight. Each cap shall be provided with a liner pad and facing. The facing shall be m

48、ade of material that will provide a lealcpmf seal (see figue 11). 3,4.5 spout closure. 3.4.5.1 Riaid swut closure. Rigid spout closums shall be made of either metal or plastic, as specified (see 6.1), and shall be not less than 7/16 inch nor more than 1-3/8 inches high. When installed, spouts shall

49、be suitably sealed and shall be so constructed as to be opened by perforation, cutting, or other acceptable method. Metal spouts shall be designed for at-chment to the can by clinching, rolling, or soldering, or by a Wded cap and gasket. The spout shall be fitted with a small, knurled, threaded, or friction cap capable of resealing the end of the spout after opening. Closures, spuuts, liners, pads, and facings (when used) shall be made fran matexials which will p