ARMY MIL-W-48763-1975 WRENCH FUZING ANTI-PERSONNEL MINE M25《M25型杀伤地雷引信扳手》.pdf

《ARMY MIL-W-48763-1975 WRENCH FUZING ANTI-PERSONNEL MINE M25《M25型杀伤地雷引信扳手》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-W-48763-1975 WRENCH FUZING ANTI-PERSONNEL MINE M25《M25型杀伤地雷引信扳手》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-STD-105 - Sarling Procedures and Tables for Inspection by Attributes (ABC-STD- 105) MIL-STD-331 - Fuze and Fuze Components, Environ- mental and Performance Tests for MIL-STD-1169 - Packaging, Packing, and Marking $or Shipment of Inert Ammunition Components Provided by IHSNot for ResaleNo reprodu

2、ction or networking permitted without license from IHS-,-,-MIL-W-48763 (PA) DRAWINGS U.S. ARMY PICATINNY ARSENAL 9214053 - Wrench, FuzFng, An.ti-Personnel Mi.ne, M25 (Copies of specifications, standards, and drawings required by contractors in connection with specific procurement functions should be

3、 obtained from the procuring activity or as direc.ted by the Contracting Officer), 3- REQUIREMENTS 3.1 Material. - Materials and parts shall be in accord- ance with applicable drawings and specifications. 3.2 Wrench. - The wrench shall comply with all require- ments specified on drawing (Dwg.) 92140

4、53 and with all require- ments specified on applicable specifications 303 Protective finish, - There shall be no evidence of rust or corrosion of metals due to salt deposits when the wrenches are subjected to salt fog per MIL-STD-331, Test 107.1. 3.4 Workmanship. - All parts shall be fabricated and

5、finished in a thorough workmanlike manner, and all manufacturing, processing, and assembly operations shall be correctly performed. They shall be clean and free of burrs, sharp edges, unblended radii, surface defects, chips, dirt, grease and oil (except where specifically required). The cleaning met

6、hod used shall not be injurious to any part or assembly nor shall they be contaminated by the cleaning agent. Exterior surface coatings shall be continuous except for a few light scratches not exposing base material, All required markings shall be neat and sharply defined. Required packing shall be

7、dry. 4 . QUALITY ASSURANCE PROVISIONS 4, 2 Classificaton of Snspectlon. - The follQwing type of Snspection shall be conducted on this item Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking perm

8、itted without license from IHS-,-,-E H Ei u w pi 0 H E w 2 O G u k d 4 P c3 H 4 rl Lr O ri i- I u Y m ri Cu =3 3 Cu Cu= M MM . . . . O0 o O00 o O0 a, n a, c O a cc o ri d Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Q04. 3 TestLng 4.4.3.1 Protecti

9、ve finish (see 3.3) - MaJor A defect - A sample of ten (10) wren-ches shall be selected from each lot for this test. ments.specified the lot shall be rejected. The test shall be as specified in 4.5.1. If any wrench fails to comply with the require- 4.4.4. Inspection Equipment . - The inspect-ion equ

10、ipment required to perform the inspections and tests prescribed in this specification is identified in the Paragraph Reference/ Inspection Method column in the table of paragraph 4.4.2.1 and the test method paragraph (see 4.5). tor shall submit for approval, inspection equipment designs in accordanc

11、e with the terms of the contract. See Section 6 of MIL-A-48078, and Section 6.2 herein. The contrac- 4.5 Test Methods and Procedure 4.5.1 Protective finish. - The wrenches shall be subjected to the salt fog specified in MIL-STD-331, Method 107.1 except that exposure test time shall be 24 hours minim

12、um (min.). 5. PREPARATION POR DELVERY 5.1 Preservation and packaging 5.1.1 Level C. - The wrenches shall be packaged in accord- ance with MIL-STD-1169 in such a manner that no damage will occur dwing shipment. 5.2 PackinG 5.2.1 Level C. - The wrenches shall be packed in accord- ance with MIL-STD-116

13、9. 5.3 Marking. - Unit, intermediate and exterior containers 6. NOTES 6.1 shall be marked in accordance with MIL-STD-1169 requirements. _. Intended Use. - The wrench covered by this specification is intended for use with the 605 fuze and the M16A1 or A2 anti- personnel mine. 5 Provided by IHSNot for

14、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-48763 (PA) 6.2 Ordering Data. - Procurement documents shall specify the following: a. Title, number and date of this specification. b. Provisions of MIL-A-48078. 6.3 Submission of Inspection Equipment Designs for .Appr

15、oval (See MIL-AO) ., Submit equipment designs as Yequired, to Commander, Picatinny Arsenal, ATTN: SARPA-&A-T-T, Dover, New Jersey 07801. 604 Distribution of ammunition data cards. - Distribution of data cards shall include the following: Commander, Picatinny Arsenal, ATTN: SARPA-QA-A-M, Dover, New Jersey 07801. Cus to di an : Army-PA Project Number: 1345-A-i23 Preparing Activity: APW-PA * u. s. GOVERNMENT PRINTING OFFICE: 1975 -60%766/042a 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-