ARMY MIL-V-62008 B-1983 VEHICLE COMBAT ENGINEER FULL TRACKED 165MM GUN M728《M728全履带式战斗工兵车 配备一门能发射黏着榴弹的165毫米火炮》.pdf

《ARMY MIL-V-62008 B-1983 VEHICLE COMBAT ENGINEER FULL TRACKED 165MM GUN M728《M728全履带式战斗工兵车 配备一门能发射黏着榴弹的165毫米火炮》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-V-62008 B-1983 VEHICLE COMBAT ENGINEER FULL TRACKED 165MM GUN M728《M728全履带式战斗工兵车 配备一门能发射黏着榴弹的165毫米火炮》.pdf（54页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-V-6200B 23 m 7977706 0379573 4 m MIL-V-62008B(AT) 16 May 1983 SUPERSEDING MIL-V-62008A(AT) 29 November 1976 M60PD-V-62283A(AT) 31 July 1981 e MILITARY SPECIFICATION VEHICLE, COMBAT ENGINEER FULL TRACKED: 165MM GUN, M728 L This specification is approved for use by the US Army Tank-Automotive Co

2、mmand, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of full-tracked armored combat vehicle which mounts a 165MM gun as primary weapon. 2. APPLICABLE DOCUMENTS 2.1 Government docum

3、ents. 2.1.1 Specification and standards. Unless otherwise specified (see 6-21, the following specifications and standards of the issue listed in that - issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of-this specification to

4、 the extent specified herein. SPECIFICATIONS FEDERAL TT-E - 5 2 7 MILITARY MIL-P-5 14 MIL-L-2104 - Enamel, Alkyd, Lusterless - Plates, Identification, Instruction and - Lubricating Oil, Internal Combustion Marking, Blank, Engine, Tactical Service. Beneficial comments (recommendations, additions, del

5、etions) and any pertinent data which may be of use in approving this document should be addressed to: US Army Tank-Automotive Command, ATTN: DRSTA-GSS, Warren, MI 48090, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document, or

6、 by letter. FSC 2350 J Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-45212 MIL-E-52798 MIL-V-62060 STANDARDS FEDERAL FED-STD-595 MILITARY MIL-STD-105 MIL-STD-130 MIL-STD-193 MIL-STD-210 MIL-STD-417 MIL-STD-461 MIL-STD-462 MIL-STD-642 MIL-STD-

7、1474 - Mount, Gun; Mount, Howitzer. - Enamel, Alkyd, Camouflage. - Vehicle, Combat Engineer, Full-Tracked: 165MM Gun, M728; Processing for Storage and Shipment of. -_ Colors. Sampling Procedures and Tables for Inspection by Attributes. Identification Marking of U.S. Military Property. Painting Proce

8、dures Tactical Vehicles (Tracked and Wheeled). Climatic Extremes, for Military Equipment. Classification System and Tests for Solid Elastomeric Materials. Electromagnetic Emission and Susceptibility Requirements for the Control of Electro- magnetic Interference. Electromagnetic Interference Characte

9、r- istics, Requirements for Equipment. Identification Marking o Combat and Tactical Transport Vehicles. Noise Limits for Army Materiel. 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification

10、 to the extent specified herein. DRAWINGS ARMY 8736334 8752278 10940 104 109401 35 - Vehicle, Combat, Engineer Full Tracked - Force Gage. - Installation, Mount, Combination Gun, M150. - Production Lubrication Chart. 165MM Gun, M728. (Copies of specifications, standards, and drawings required by manu

11、facturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting off iter* ) _. 4. 2.1.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of t

12、his specification shall take precedence. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e lz a MIL-V-6200B 23 m 797790b 0179575 m 3. REQUIREMENTS .:. -, I .: . MIL-V-62008B(AT) 3.1 Preproduction vehicle. When s.pecified (see 6.2), a preproduction ve

13、hicle of the complete vehicle to be furnished under this specification, shall be produced prior to the manufacture or fabrication of vehicles in quantity. The vehicle shall be submitted to the Government for examination and tests to determine conformance to the requirements of this specification. Ve

14、hicle submitted by the contractor shall be fully representative of vehicles proposed to be supplied by the vehicle manufacturer from production facilities and tooling under the supply contract. 3.2 First production vehicle. A first production vehicle shall be fully representative of vehicles to be f

15、urnished under the contract and shall be submitted to the Government for inspection to determine conformance to the requirements of this specification. 3.2.1 Workmanship and reliability. The workmanship shall be of a quality to assure that the vehicle and components are free from defects that compro

16、mise, limit, or reduce the vehicle or component capabilities. Vehicles made in accordance with this specification shall be subjected to examinations and tests to prove vehicle capabilities to perform in accordance with the following: a. Vehicle shall require only organizational maintenance (first an

17、d second echelon) during 2,000 miles of normal operation. Vehicle shall require no replacement or major overhaul of any major automotive component during 4,000 miles of normal operation. Complete track assemblies or individual shoes shall not require replacement during 2,000 miles of normal operatio

18、n. b. c. 3.2.1.1 Vehicle operation. The 4,000 miles of vehicle operation combat loaded or simulated load that will not change the normal combat load center of gravity shall consist of the following: a. 25 percent on paved roads either concrete, asphalt, or any combination of the two. b. 25 percent o

19、n gravel and dirt roads with at least 10 percent of this distance under mud conditions. C. 25 percent on level cross country. d. 25 percent on hilly cross country. 3.3 Materials. 3.3.1 Qualified products. All assemblies and component parts requiring product qualification in accordance with the perti

20、nent specifications or drawings listed on the EPL cited in 3.4 and necessary in the construction of this vehicle, contractor shall be responsible for using only those products that are listed (by part or drawing number as QPL items) on the QPL in.the Provided by IHSNot for ResaleNo reproduction or n

21、etworking permitted without license from IHS-,-,-referenced specification, or which have been approved for inclusion on such lists. Manufacturers inspection records shall specifically list such component(s), name of supplier(s) (as listed on the QPL or in the approval letter), and number and date o

22、the QPL from which the selection was made, or date of approval letter when poducts are approved but not as yet listed on the QPL. all rubber components that are under tension or which may be flexed, shall be ozone resistant to the degree required by the “Cl“ test requirements of MIL-STD-417. i 3.3.2

23、 Ozone resistance. bicle operating conditions. shall contain a domelight to provide general illumination to assist with tasks at night or during closed-hatch operation. provisions for adjusting light intensity and red filter for night vision adaptation. I 3.4.9.2 nterior lighting. Each crew position

24、 except commander cupola, The domelight shall contain 3.4.9.3 Hull-to-turret slipring. The hull-to-turret slipring shall provide power and signal circuits capable of maintaining positive electrical contact between the hull and turret electrical subsystems under all vehicle environments. A sealed air

25、 passage in the slipring shall be capable of 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-b !MIL-V-b200B 23 9797706 0377577 5 carrying low-pressure air for the gas particulate subsystem. hydraulic fluid passage in the slipring shall be capable o

26、f carrying supply pressure, return pressure, and drain pressure for the vehicle hydraulic control system. Sealed 3.4.9.4 Cupolaslipring. The slipring assembly shall provide uninterrupted power continuity of seven electrical circuits between the turret and cupola. any kind into the communication syst

27、em. Operation of the slipring shall not introduce static of 3.4.9.5 Auxiliary outlet. Two outlets (24 direct current volts vdc nominal), one each in the turret and hull shall be provided that will mate with the OVE trouble light assemblies. be protected with a 15 ampere automatic reset circuit break

28、er. Each auxiliary outlet circuit shall 3.4.9.6 Searchlight system. 3.4.9.6.1 Vehicle and searchlight interface. Vehicle and searchlight requirements without searchlight installed are as follows: a. . b. C. The searchlight power circuits shall be capable of providing vehicle power for operating and

29、controlling the searchlight. The searchlight circuit shall be protected with a 60 ampere automatic reset circuit breaker. Mounting provisions shall be provided for searchlight and control box installation. 3.4.9.6.2 Searchlight. With the vehicle in a level position and the main gun at 5 mils elevati

30、on and balanced, the installed searchlight shall be capable of the following: a. b. Be operable from either the remote control box or the main control box. Have + 89 mils (+ - 5) of adjustment in the elevation and traverse screws. 3.4.9.7 Generator voltage. With the engine operating at a minimum of

31、1000 revolutions per minute (rpm), the vehicle generator shall deliver between 25.8 volts and 30.2 volts at the battery under all conditions of vehicle operation with the generator fording switch “on“. The battery voltage shall be not less than 18.5 volts when the hydraulic power pack is energized.

32、3.4.9.8 Generator blower motor. The generator biower motor shall be capable of maintaining constant flow of air through generator with the generator fording switch “on“. 3.4.9.9 Passive drivers night viewer power circuit. The voltage output at the passive drivers night viewer connector shall be with

33、in 0.2 volts of the postive battery potential when operating into a 1 ampere load. 3.4.9.10 Power plant electrical. The engine electrical installation shall contain the sending units necessary to provide engine data in the form of electrical signals to the driver instrument panel as required and sha

34、ll 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-include an engine electrical disconnect to facilitate engine removal and replacement, and shall also contain an electrical starter motor capable of starting the engine under all required conditions

35、 and air cooled generator. 3.4.9.11 Air cleaner blower motors. Each air cleaner blower motor shall be capable of providing a flow of air as specified through each blower outlet. unless the engine is running. The air cleaner blower motors shall be wired so they do not operate 3.4.9.12 Engine manifold

36、 heater. The vehicle wiring for the manifold heater shall provide a switch-actuated vehicle battery circuit to the engine. Operation of the push button switch on the purge pump handle with starter switch depressed, shall provide vehicular battery voltage to pin “A“ of the multiple connect.or at the

37、engine electrical quick disconnect. 3.4.9.13 Personnel heater. The heater shall be capable of starting with The blower motor shall operate at The burner shall ignite within 4 Subsequent to ignition, the heater shall be the switch in either high or low position. reduced speed when the heater is turne

38、d on. minutes of heater turn-on. capable of generating high and low heat and te blower motor shall run at full speed. extinguish and the blower motor to shut off within 3.5 minutes. Turning the heater “off“ shall cause both the burner to 3.4.9.14 Engine smoke generator. left and right exhaust pipes

39、when the engine is running and the smoke generator switch is in the “on“ position. The vehicle shall produce smoke in the 3.4.9.15 Communications system. Requirements for a communications system are as follows: a. b. An AN/VIC-1 (V) intercom set shall be installed and shall be functional for crew co

40、mmunications, Provisions shall be available for the installation of an AN/VRC radio that shall operate through the intercom set. 3.4.9.16 Main gun firing circuits. The main gun firing circuits shall be capable of providing the energy necessarjl (,25 ampere for 100 milliseconds) io fire main round. f

41、ollowing: The firing circuit shall also provide the at b. The probe shall be grounded at all times except during application of the firing voltage. The firing control circuits shall include the switching feature which prevents subsequently loaded rounds from detonating until the firing switch has be

42、en released after the previous round. Interconnections shall be provided to allow firing circuit: activation from the alternate emergency switch on the manual elevation pump handle and provide emergency mode firing per C. 3.4.90 18. 3.4.9.17 Machine gun firing circuits. The machine gun firing circui

43、ts shall be capable of providing the energy necessary (13 amperes) to operate respective machine gun solenoids. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-k _ MIL-V-62008B 23 m 7777706 0177583 3 a 3.4.9.18 Main gun and machine gun circuit cont

44、rols. The firing circuit controls shall be arranged and interlocked to allow the commander to fire the main gun, coaxial machine gun, and the cupola machine gun and to allow the gunner to fire the main gun and the coaxial machine gun, be provided with protection against accidental firing by a loader

45、s safety switch which interrupts the commander and gunner firing circuits automatically during gun recoil. The switch shall thereafter remain in the safe (open circuit) position until manually returned to the fire (closed circuit) position by the loader. alternate source of electrical power for emer

46、gency firing of the main gun through the loader safety switch. The main gun shall The blasting machine shall provide an 3.4.9.19 Smoke grenade discharger circuits. 3.4.9.19.1 Arming. The power-on (ready) lamp in the grenade power box shall illuminate when the master battery switch, turret power swit

47、ch, and the grenade system power switch are all on. Right discharger firing pins 3, 4, 6 1, 2, 5 1, 2, 5 3, 4, 6 3.4.9.19.2 Circuit voltage. Voltage at the smoke grenade discharge firing pins shown in figure 6 shall be as indicated in table I when the power-on (ready) lamp in the grenade power box i

48、s illuminated and the appropriate firing pushbutton is actuated, Voltage Vehicle (Ref. 3.4.9.7) O + 0.5 VDC Vehicle (Ref. 3.4.9.7) O + 0.5 VDC TABLE I - Grenade discharger circuit voltage. iring ,ushbut t on Right Right Left Left Left discharger firing pins 1, 2, 5 3.4.10 Vision devices and receptac

49、les. Provisions shall be made to assure that receptacles incorporated fn the vehicle will accept applicable vision devices without binding or interference. periscope receptacles shall accept the periscopes, and when installed, removed, and reinstalled the line of sight shall not deviate more than 0.2 mil from the line of sight of initial installation setting. the periscope receptacles, vision devices, and vision blocks shall prevent the entranc