ARMY MIL-T-62097 C-1991 TRUCK MOTOR HOME SHELL FOR CUSTOMIZATION INTO MOBILE LABORATORY ELECTRONICS VAN WORK AREA ETC 14 000 POUNDS GVW 4X2 MODIFIED COMMERCIAL《GVW为14000磅 规格为4X2 用.pdf

《ARMY MIL-T-62097 C-1991 TRUCK MOTOR HOME SHELL FOR CUSTOMIZATION INTO MOBILE LABORATORY ELECTRONICS VAN WORK AREA ETC 14 000 POUNDS GVW 4X2 MODIFIED COMMERCIAL《GVW为14000磅 规格为4X2 用.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-62097 C-1991 TRUCK MOTOR HOME SHELL FOR CUSTOMIZATION INTO MOBILE LABORATORY ELECTRONICS VAN WORK AREA ETC 14 000 POUNDS GVW 4X2 MODIFIED COMMERCIAL《GVW为14000磅 规格为4X2 用.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、NOT MEASUREBENT SENSITIVE MIL-T-62097C 10 October 1991 SUPERSEDING 29 September 1982 MIL-T-62097B MILITARY SPECIFICATION TRUCK, MOTOR HOME SHELL, FOR CUSTOMIZATION INTO MOBILE LABORATORY, ELECTRONICS VAN, WORK AREA, ETC., 14,000 POUNDS GW, 4x2, MODIFIED COMMERCIAL This specification is approved for

2、use by all departments and agencies of the Department of Defense. 1. SCOPE * 1.1 Scorn. This specification covers diesel and gasoline engine driven four-wheel, two-rear wheel drive, forward control motor home shells, having a minimum gross vehicle weight (GVW) of 14,000 pounds, for normal operating

3、conditions. The vehicle has an integral drivers compartment and body for later installation of such special equipment as may be desired. Vehicles procured under this specification are commercial items which are warranted by the manufacturer as specified in procurement documents. 2. APPLICABLE WCUMEN

4、TS - The following % 2.1.1 Crecifications, ateda, and handbooks specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specific

5、ations and Standards (WDISS) and supplement thereto, cited in the solicitation (see 6.2). .I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-URD, War

6、ren, MI 48397-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A 1. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted wi

7、thout license from IHS-,-,- MIL-T-62097C 23 W 9799906 0493455 O SPECIFICATIONS FEDERAL W-B-131 y: A-4-393 Y W-F-800 MI LI TARY MIL-P-514 % MIL-T-58S4 MIL-B-46176 CTANDARDC FEDERAL * FED-STD-297 - Battery, Storage: Vehicular, Ignition, - Ext inwishers , Fire, Dry-Lxemical (Hand - Fuel Oil, Diesel. Li

8、ghting and Starting. Portable 1 - - Plate, Identification, Instriiction And - Turbine Fuel Aviation, Grades JP-4 and JP-5. - Brake Fluid, Silicone, Automotive All - Turbine Fuel, Aviation, Kerosene Type, Grade Marking, Blank. Weather, Operational and Preservative. JP-B . - Riistproofing of Commercia

9、l (Nontactical) Vehicles. MILITAFCZ MIL-STD-209 MIL-STD-i223 - Slinging and Tiedown Provisions for Lifting and Tying Down Military Equipanent. - Non-Tactical Wheeled Vehicles Treatment, Painting, Rustproofing, Identification Marking, and Data Plate Standards. Fixed Wing Aircraft :# MIL-STD-1791 - De

10、signing for Internal Aerial Delivery in * (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specification ancl Standards, Bldg. 4D, 700 Robbinc Avenue Philadelphia, PA 19111-5094.)

11、 * 2.1.2 Other Gov =ment docats. drmas. and mbbcations; . The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. the issues are those cited in the solicitation. Unless otherwise specified, :K DEPARTMENT OP DEFENSE (DOD) Depar

12、tment of Deense Index of Specifications and Standards (WISISS). (Copies of DODISS are available on a yearly subscription basis either from the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Ave

13、nue, Philadelphia, PA 19111-5093.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-T-tjS097C :K AFSC DESIGN HANDBOOK DH- 1- 11 - Air Transportability i-iandbook (Application for copies of the AFSC Design Handbook should be addressed to Wright-

14、Patterson AFB, ASD/ENESS, Mr. Rod Wright, Wright-Patterson APB, OH 45433, telephone (513) 255-6281.) DEPARTMENT OF TRANSWRTATION (DOT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. (Application for copies of DOT publications should reference the Code of Federal Re

15、gulations, 49 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Noise Emission Standards for

16、 Transportation Equipment - Medium and Engines. Heavy Trucks. (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 2

17、0402.) * 2.2 Nonent - Dublications . The following documents form a part of this document to the elrtent specified herein. the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not listed in the DODISS are the

18、 issues of the documents cited in the solicitation (see 6-2). Unless otherwise specified, Unless otherwise specified, * AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM D 4985 - Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring an Init

19、ial LGarge of Supplemental Coolant Additive. (Application for copies of ASTM publications should be addressed to American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) * THE EUROPEAN TYRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual (Application for copies

20、of ETRTO publications should be addressed to the European ere and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. _ j NIL-T-bZ097C 23 999990b 0493457 4 MIL-T-62097C NATIONA

21、L FIRE PROTECTION ASSOCIATION (NFPA) NFPA No. 70 - National Electrical Cade * (App1ic:ation for copies of NFPA publications should be addressed to the National Fire Protection Association, 60 Batterymarch Park, Quincy, MA 02269. I SAE, INC. * 5350 SAE Standards tJ537 x 5551 5588 J68S 5589 5688 % 513

22、49 and Recommended Practices - Spark Arrester Test Procedure for Mediiun - Storage Batteries. - Limits and Methods of Pleasurement of Radio Size Engines (DoD Adopted). Interference Characteristics of Vehicles and Ckvicea (30-1000 MHz) (DOD adopted). - Turn Signal Lamps. - Turn Signal Svitch. - Rear

23、Wheel Splash and Stone Throw - Truck Ability Prediction Procedure. - Engine Power Test Code - Spark Ignition and Protection a Diesel. (Application for copies of SAE publications should be addressed to SAE, Inc., 400 Commonwealth Drive, Warrendale, FA 15096.) THE TIRE AND RIM ASSOCIATION, INC. Year B

24、ook. * should be addressed to the Tire and Rim Association, Inc., 175 Montrose Mest Ave-, Copley, OH 44321.) (Application for copies of the Tire and Rim Association publications (Industry association specifications and standards are generally available for reference from libraries. technical groups

25、and using Federal agencies.) They are also distributed among :+-I 2.3 Order of wecedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, supersedes applicable laws and r

26、egulations unless a specific exemption has been obtained - 3. RIIQUIREMENTS :k 3.1 ward vehicle a 3.1.1.1 btment and painting painted in accordance with MIL-CTD-1223. activity for the appropriate military service (see G.2), the exterior color shall be in accordance with MIL-STD-1223. The vehicle sha

27、ll be treated and ,I As specified by the procuring :k 3.1.1-2 Marking and data da tec. As specified by the procuring activity for the appropriate military service (see 6.2), identification marking and data plates shall be in accordance with MIL-STD-1223. When specified (see 6-21 concealed markings s

28、hall be furnished. :k 3 - 1 - 1.3 Rustproof ;Inrs - When specified (see 6.2), the vehicle shall be rustproofed in accordance with FED-STD-297. When specified (see 6-21, tropical rustproofing in accordance with FED-STD-297 shall be furnished. 3.1-1.4 Brain pluas . All drain plugs installed in manual

29、transmissions and rear axles shall be of the permanent magnet type- 3.1.1.5 bd treatm ent. in accordance with MIL-STD-1223. When specified (see 6.2), wood shall be treated Y 3 1 1 - 6 Towin- device6 . Towing devices consisting of two hooks, loops, eyes or pins or the chassis manufacturers standard s

30、ingle center mounted eye or pin shall be mounted on the front of the vehicle. X 3.1.1.7 hark ames ter. As specified herein (see 3.4.4), the vehicle shall be furnished with an exhaust system spark arrester. - When specified (see 6.2), the vehicle * 3.1.1-8 Air transwrtability shall be air transportab

31、le in C-5A aircraft in accordance with the - requirements of MIL-STD-1791 and APSG Design Handbook DH-1-11. relocation of mechanically attached (nonwelded, nonriveted, etc.) components e1 Removal or 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

32、IL-T-62097C with common hand tools, requiring not more than 1 manhour total to remove, mlorata and tiedown; and not more than 1 manhour total to return the vehicle to its original, as opposed to reduced, configuration; shall be acceptable. The self-mobility of the vehicle shall not be affected by re

33、ducing its canfigbration. furnished. the front axle and 10,000 pounds on the rear axle. requirements of 3-2.6, the rated capacity of the axles and suspension system shall be not less than 1-1/4 times the load imposed on each by the curb weight of the vehicle. The vehicle shall be air transportable a

34、s described above without any other special provisions and without any shoring. vehicle shall not be delivered to the Government in its reduced configuration. contractor. of the vehicle to the approved data will be required before acceptance of the vehicle - Tiedowns far removed or relocated equipme

35、nt shall be The curb weight of the vehicle shall not exceed 5,000 pounds on In addition to the The Drawings and data will be required to be submitted by the Government approval of the data (120 days) and then comparison Z 3.1.1.9 Liftine: and tiedown attacbentq . When specified (see 6.2), the vehicl

36、e shall be equipped with lifting and tying down attachments. Lifting and tiedown attachments shall conform to type II or type III of MIL-STD-209. In MIL-STD-209G, replace “maximum shipping weight (MSW)“ wherever it appears with “curb weight.“ (class 1 or 2) or composition (3 of MIL-P-514 shall be pr

37、ovided. The transportation plate shall be inscribed with a diagram showing the lifting attachments and lifting slings, the capacity of each attachment, and the required length and size of each sling cable. A silhouette of the vehicle showing the center of gravity shall be provided on the transportat

38、ion plate. Tying down attachments shall be identified by stenciling or other suitable marking. Tiedown markings shall clearly indicate that the attachments are intended for the tiedown of the equipment on the carrier. A transportation plate conforming to composition A 3.1.1.10 Blackout curtainq . Wh

39、en specified (see 6.Z), blackout curtains or screens shall be provided to allow operation, during blackaut conditions, of all the interior dome lights and fluorescent lights to the rear of the drivers seat. Full height transverse blackout, screens or curtains shall be provided to cover the full widt

40、h of the interior at the rear of the drivers seat. Blackout curtains or screens shall be provided for all exterior windows to the rear of the drivers seat. * 3.1.1.11 Wheel m1mh mddn . Rear end mud flaps shall be provided. than 1 inch wide, extending the entire width of the mud flap, shall be instal

41、led to prevent the bolt heads or bolt nuts from damaging the mud flap. As an alternate method of attaching the mud flaps, tabs or clips with minimum surface contact dimensions of 1 inch high by 1.25 inch wide by 0.094 inch thick shall be furnished at each bolt. to the rear wheel splash and stone thr

42、ow protection provisions of CAE 5682. A metal strip not less than 0.125 inch thick and not less fiid flap installations shall conform 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-T-62097C 23 3.1.1-12 Silicone brake fl When specified (see 6.2

43、), and if available as the manufacturers standard or optional brake fluid, brake fluid conforming to MIL-B-46176 shall be provided in the hydraulic brake system. A decal or plate shall be placed near the master cylinder stating “CAUTION: IJSE SILICONE BRAKE FLUID ONLY, MIL-B-46176.” * 3.1.1.13 -_ At

44、 least one pair of brake lights shall override the four-way emergency flasher or the two systems shall be independent of each other. accommodate this requirement shall not compromise conformance to any Federal Motor Carrier Safety Regulation referenced herein or to any Federal Motor Vehicle Safety S

45、tandard- If additional lights are added to the vehicle, the lights shall be selected from the chassis manufacturers standard matching hardware. Modifications to the manufacturers standard product to 3.2 General desia. 3.2-1 Federal Motor Vehicle Safetv Stardardsi - The vehicle shall comply with all

46、Federal Motor Vehicle Safety Standards in effect on the date of manufacture 3.2.2 Aj,r pollut ion cantrd . The vehicle shall comply with Environmental Protection Agency Regulations governing Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Engines in effect on the date of manuf

47、acture. comply with State of California regulations governing air pollution control in effect on the date of manufacture. In addition, vehicles destined for California shall itr 3.2.3 Sound level. The interior sound level shall not exceed 84 and a full complement of fuel, lubricants, and coolant. 3.

48、2.5 . Gross vehicle weight (GW) shall consist of curb weight, operator (weight computed at 175 pounds), and a payload to provide a total GW of not less than 14,000 pounds. 3.2.6 Wei- - The distribution of the GW for the purpose of establishing suspension, axle and tire capacity shall be determined w

49、ith the payload uniformly distributed over the payload area. shall be measured at the ground. Rated capacities 3.2.7 Weelbaae- The wheelbase shall be not less than 178 inches, measured between the centerlines of the front and rear axles. (see 6.2), wheelbase shall be compatible with the body make and model spec if ied When specifiec 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-bZ097C 23