ARMY MIL-T-45380 E-1991 TRUCKS MAINTENANCE EARTH AUGER TURNTABLE BASE DIESEL ENGINE DRIVEN 28 000 POUNDS GVW 4X4 MODIFIED COMMERCIAL《4X4规格 GVW(总重量)为28000磅 柴油发动机驱动的转台型基座钻孔机的商用维修车》.pdf

《ARMY MIL-T-45380 E-1991 TRUCKS MAINTENANCE EARTH AUGER TURNTABLE BASE DIESEL ENGINE DRIVEN 28 000 POUNDS GVW 4X4 MODIFIED COMMERCIAL《4X4规格 GVW(总重量)为28000磅 柴油发动机驱动的转台型基座钻孔机的商用维修车》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-45380 E-1991 TRUCKS MAINTENANCE EARTH AUGER TURNTABLE BASE DIESEL ENGINE DRIVEN 28 000 POUNDS GVW 4X4 MODIFIED COMMERCIAL《4X4规格 GVW(总重量)为28000磅 柴油发动机驱动的转台型基座钻孔机的商用维修车》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-T-45380E -23 W 9999906 0480839 2 ML-T-45380E(AT) I991 SUPERSEDING MIGT-45380D(AT) 29 May 1980 MILITARY SPECIFICATION YI TRUCKS, MAINTENANCE: EARTH AUGER, TURNTABLE BASE, DIESEL ENGINE DRIVEN, 28,000 POUNDS GW, 4x4, MODIPIED COMMERCIBL This specification is approved for use by the US Army Tank- A

2、utomotive Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense - 1. SCOPE * 1.1 Scom. This specification covers an earth auger with a turntable, mounted on a diesel engine driven, four-wheel, four-wheel drive, modified commercial truc

3、k chassis having a minimum gross vehicle weight (GW) of 28,000 pounds for normal operating conditions. specification are commercial items which are warranted by the manufacturer as specified in acquisition documents. Vehicles procured under this Beneficial comments (recommendations, additions, delet

4、ions) and any pertinent data which may be of use in improving this dociunent should be addressed to: US Army Tank-Automotive Command, ATTN: AMCTA-UED, Warren, MI 48397-5000, by using the self-addressed Standardization Dociunent Improvement Proposal (DD Form 1426) appearing at the end of IS dociunent

5、 or bv letter. AMSC N/A UTION CITATEMENT I- A. Approved for public release; distribution i3 unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BIL-T-45380E 23 9997906 0480820 9 CIIL-T-45380E AT f 2. APPLICABLE DOCUMENTS P 2.1 Gaverment d ocwe

6、nte - x 2-1-1. Swec if ications: stan dards, and handboo h. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. documents are those listed in the issue of the Department of Defence Index of Specifications and Standards (I30DISS) and sup

7、plement thereto, cited in .the solicitation (see 6.2). Unless otherwise specified, the issues of these SPECIFICATIONS FEDERAL W-B-131 - Battery, Storage: Vehicular, Ignition, Lighting and Starting- * W-F-800 - Fuel Oil, Diesel- SPECIFICATIONS MI LI TARY * MIL-P-5 14 - Plates, Identification, Instruc

8、tion and x MIL-T-5624 - Turbine Fuel, Aviation, Grades JP-4 and. x MIL-M-43719 - Marking Materials and Markers, Adhesive, Marking, Blank. JP-5 - Elastomeric, Pigmented, General Specif cation for - * MIL-T-83133 - Turbine Fuel, Aviation, Kerosene Type, Grade JP-13, STANDARDS FEDERAL * FED-STD-297 - R

9、ustproofing of Commercial (Nontactical) Vehicles. MILITARY y: MIL-STD-1223 - Nontactical Wheeled Vehicles Treatment, Painting, Identification Marking and Data Plate Standards - - Light, Warning, Vehicular, Rotating, D.C- MS51317 MS51335 - Pintle Assembly, Towing - 18,000 Lbs. Capacity, Hanual Releas

10、e. * specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications and Standards, Bldg- 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) Unless otherwise indicated, copies of federal and military Provided by IHSNot for ResaleNo repr

11、oduction or networking permitted without license from IHS-,-,-MIL-T-45380E 23 W 999990b 84O2E CI W vernment d ocwnents, drawinm. ancgublications . The * 2.1-2 Other ;rn fnllowing other Government Gocuments, drawings, and publications form a part of this document to the extent specified herein. the i

12、ssues are those cited in the solicitation. .-i Unless otherwise specified, e ;k CIEPARTMENT OF DEFENSE (WD) Department of Defense Index of Specifications and Standards (WEISS). (Copies of the WDISS are available on a yearly subscription basis eithw from the Government Printing Office for hard copy,

13、or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093-) DEPARTMENT OF TRANSPORTATION (DoT) Pederal Motor Carrier Safety Regulations. Feder*al Motor Vehicle Safety Standards. (Application for copies of DOT p

14、ublications should reference the Code- of Federal Regulations, 49 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U.6- Government Printing Office, Washington, D.C. 20402-) ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicle

15、s and New Motor Vehicle Noise Emission Standards for Transportation Equipment - Medium and Engines - Heavy Trucks, (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CPR, and the Federal Register and should be addressed to the Superintendent of Documents

16、, U.S. Government Printing Office, Washington, D-C. 20402-) lications. L.L Bon-Government pub The following documents form a part of .* 0 ci this document to the extent specified herein. the issues of the documents which are DoD adopted are those listed in the issue of the I)ODISS cited in the solic

17、itation- the issues of documents not listed in the WDISS are the issues of the documents cited in the solicitation (see 6.2)- Unless otherwise specified, Unless otherwise specified, AMEXICAFi SOCIETY FOR TESTING ANT! MATERIALS (ASTM) Stamlards: .K ASTM Designation: A53 - Pipe, Steel, Black and Hot-D

18、ipped Zinc-Coated Welded and Seamless, for Ordinary Uses (IbD adopted). (Application for copies of ASTM publications should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, FA 153103. i 3 Provided by IHSNot for ResaleNo reproduction or networking permit

19、ted without license from IHS-,-,-MIL-T-4538OE 23 = 999990b 0480822 2 W :k THE EURPEAN TYRE AND RIM TECHNICAL ORGANISATON BTRTO) Ctanciwds Manual. (Application for copies of ETRTi) publications should be addressed tu the European Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 8russei3

20、, Belgium.) SAE, IRC. SAE Stanards and Recommended Practices ,* 5318 - Air Brake Glackand Service (Control) and Emergency (Supply) Line Coupiers - Trucks, Truck-Tractors , and Trailers (POD aduptedj - Size Engines (DoD adopted). :k 5350 - Spark Arrester Test Procedure for Pleciium 5537 - Storage Bat

21、teries. :% 5551 - Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1,000 MHz). - Seven-Conductor Electrical Connector for Truck-Trailer Jumper Cable. 55130 5588 - Turn Signal lamps. d539 - Turn Signal Switch. Je82 - Rear Wheel Splash and Stone

22、Throw Protection (Doi) adopted). Combinations of Vehicles. yc J683 - Tire Chain Clearance - Trucks, Buses, and J686 - Truck Ability Prediction Procedure. * 5704 - Openings for Six- and Eight-Bolt Truck x 5706 - Rating of Winches. Transmission Mounted Power Take-offs. 5844 - Nonmetallic Air Brake Sys

23、tem Tubing (DoD adopted . Truck-Trailer Connections - Diesel. ;1: 51067 - Seven-Conductor Jacketed Cable far * J1349 - Engine Power Test Code - Spark Ignition and P Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) Application for copies of SAE publications should be addressed to SAE, THE TIRE AN

24、D RIM ASSOCIATION. INC- Year Book * (Application for copies of Tire and Rim Association publications should be addressed to The Tire and Rim Association, Inc., 175 Montrose West Ave., Capley, OH 44321.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

25、-,-MIL-T-45380E 23 999990b 0480823 4 E Y frmi t-he organizations that. prepare or uistri?nute the documents documents also may be available in UP through libraries or other inorrnat ional services. I (Non-Government standards and other piibiications are normally available These X this document and t

26、he references cited herein, the text of this document takes precedence. Nothing in this dociment? however, supersedes applicable laws and regulations unless a specific exemp%ion has been obtained. 2.3 Order of Preceder ice. In the event of a conflict between the text of 3. REQUIREMENTS :K 3.1 Sialda

27、rd vehicle and ar: cessori ?eq. Except as specified in 3.1.1 through 3.1.1-13, the vehicle, compnents, assemblies, and accessories to be delivered under the contract shall be standard or optional items, which meet or exceed the requirements of this specification. 3-1.1 through 3.1.1.13, no removal,

28、substitution or-alteration of the chassis manufacturer?s standard or optional chassis model components shall be made- All chassis items shall be as represented in the chassis manufacturer?s t.echnica1 data book. represented in the body and equipment manufacturer?s technical data. Tec.hnica1 data sha

29、ll be limited to specifications and technical material, icientical to that furnished to the authorized company representatives for selection of vehicle models and components, and shall be available to the engineering office of the procuring activity prior to delivery of the items. The chassis model

30、furnished shall be not older than the chassis manufacturer?s current model on the date of invitation for bids, Except as specified in Ssecial bodies or mounted equipment shall be as 3.1.1 ? e - In addition to the standard vehicle and component specified in 3.1, the vehicle shall be furnished with sp

31、ecial equipment as specified herein. . The vehicle shall be treated and .# 3.1-1.1 Treatment and painting painted in accordance with MIL-STD-1223. activity for the appropriate military service (see 6.2), the exterior color shall be in accordance with MIL-STD-1223, ? As specified by the procuring Y 3

32、.1-1.2 b, ri. 1.1.12 Frake light5 - At least one pair of brake lights shall override the four-way emergency flasher or the two systems shall be independent of each other. accommodate this requirement,shali not compromise conformance to any Federal Motor Carrier Safety Regulation referenced herein or

33、 to any Federal Motor Vehicle Safety Standard. If additional lights are added to the vehicle, the lights shall be selected from the chassis manufacturers standard matching hardware. Modifications to the manufacturers standard proriuct to * 3.1.1.13 4x4 converskm - The chassis manufacturers standard

34、4x2 truck chassis may be modified to provide all wheel drive conforming to the requirements specified herein if: The canveraion ale- manufacturers engineering department specifically approves and certifies that all such modifications meet the design requirements and standards of the conversion axle

35、manufacturer. and proving ground test reports, which shall be made available to the engineering and quality assurance offices of the procuring activity - Tha chasais mailufacturer ti front .ale before cmivsraiaii haa the srne load rating as the conversion icule to be installed. Components used in th

36、e all wheel drive conversion are of current product ion. Components used in the all wheel drive conversicn are approved for the conversion application by the component manufacturers. The converted vehicle is certified to conform to Federal Motor Vehicle Safety Standard No. 121, by the intermediate o

37、r final manufacturer. Certification shall be based on both design analysis Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-4538OE 23 I 9999906 0480826 T I . ff., 3,s Replacement headligh required to be ad shall meet the height requirement of in

38、ches, measured above the road surface, in Notor Vehicle Safety Standard No. 108. Replacement headlights shall be equivalent in mount g, protection, and range and precision of adjustment to the chas headlights. Unused headlight cavities are covered in a neat warkmanlike maimer, treated and painted to

39、 match the chassis cab coior with treatment and painting equivalent to the chassis cab manufacturers process for the remainder of the chassis cab. shall be -rustproofed in accordance with 3-1-1-3- Complete installation drawings are available to the procuring activity - Ideneral des;hgia- less than 2

40、2 inche not mope than 54 s manufacturer s origina1 standard Cavities and their covers 3.2-1 accessories shall comply with all Federal Motor Vehicle Safety Standards in effect on the date of manufacture. Feder al Motor Vehicle Safe tv Ctandar ds. The vehicle and furnished The vehiele shall comply wit

41、h Ehe egulations governing and New Motor Vehicl the date of manufacture. comply with State of California regul In addition, vehicles destined for California shall ions governing air- wllution contrd in effect on the date of manuf . The curb weight hall include the weight of chassis and cab, with all

42、 attachments, accessoriesJ and equipment; bo ful complement of fuel, lubricants, and coolant. 3-2-5 Gr0s.s vehicle we- . - The GVW Shall consist of curb weigh%, operator weight (compute than the specified GW. GW computed with 525 pounds 175 pounds), and a payload, to provide not less le with Greg (f

43、ours-door) cab shall have the payload in the rear seat, 3.2.6 bebt a. distribution stribution of the GVW for the yiirpse g suspension, ax ad uniformly-dis over the load area- ire capacities shall be determined i3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

44、om IHS-,-,-MIL-T-45380E 23 W 999990b 0480827 I W .C 3.2-7 ilirJlension. The cab-to-ade dimension shall be not less than 102 inches but may be reduced not more than 2 inches when the vehicle is furnished with a tilt type cab. :# 3.2.8 Ratia. Vehicle ratings shall be the manufacturers published rating

45、s. requirements of this specification. available, verification of ratings must be submitted to the engineering 0ffic.e of the procuring activity. punds . * 3.2.9 Accessibilitv _ _ The design of the vehicle and optional equipent shall permit access for routine servicing and shall permit access for re

46、placement and adjustment of component parts and accessories with minimal disturbance of other components and systems- Component and vehicular ratings shall not be raised to meet the When piblishe ratings me not The minimum GW rating shall be 28,000 :* 3-2-10 Asbes toa. Asbestos materials shall not b

47、e used in any form in any part of the vehicle. ;3 - 3 Perf ormanc e. Performance requirements shall be met with the front wheel drive disengaged and with front wheel driving hubs unlocked, except that vehicles equipped with interaxle compensating devices shall meet performance requirements with the

48、front wheel drive engaged. 3.3.1 Speeds and ma deabilitv . High and low speed requirements shall be met with the truck loaded to specified GW. 3.3.1-1 HiEh meed gradeability - The vehicle shall ascend a continuous grade of 1.0 percent at 50 miles per hour (mph). Gradeability requirements shall be me

49、t with the main transmission in direct drive. Gradeability shall be verified with calculations in accordance with SAE 5688 (see 6.3). 3-3.1.2 Jiow speed. Low speed shall be calculated with the engine operating at not less than 35 percent of the recommended governed speed, and shall provide not more than the vehicle speed (mph) specified in table I for the corresponding number of available forward speeds. TABLE I. IrOkJrements ds 3.0 3.3.