ARMY MIL-T-44372 A-1991 TROUSERS AIRCREW COMBAT《战斗人员裤》.pdf

《ARMY MIL-T-44372 A-1991 TROUSERS AIRCREW COMBAT《战斗人员裤》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-44372 A-1991 TROUSERS AIRCREW COMBAT《战斗人员裤》.pdf（43页珍藏版）》请在麦多课文档分享上搜索。

1、a. T * MIL-T-Y4372A 84 9999906 0493982 L MIL-T-44372A 30 September 1991 SUPERSEDING MIL-T-44372 5 June 1989 MILITARY SPECIFICATION TRWSERS, AIRCREW, CCBIWlT This specification is approved for use by all Departments and Agencies of 2 the Department of Defense. 2. SCOPE 1.1 Scope. This specification c

2、overs plain weave, aramid, combat trousers for use by aircrew personnel. * 1.2 Classlfication. sizes as specified (see 6.2). The trousers shall be of the following classes and Class 1 - Woodland Camouflage Class 2 - Tan 380 Schedule of sizes x-small small Medium Larqe X-Lame Short Short Short Short

3、Short Regular Regular Regular Regular Regular mng l-w Long d Beneficial comnents (reccmendations, additions, deletions) and any pertinent data which my be used in improving this doc=ument should be addressed to: U.S. Army Natick Research, Developnent, and Engineering Center, Natick, M 01760-5019 by

4、using the Standardization -nt Improvement Proposal (Dl Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlirnited. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

5、nse from IHS-,-,- MIL-T-44372A 4 = 777770b 0473783 3 W MIL-T-44372A 2. APPLICABLE l3xmmws 2.1 Govemnt documents. * 2.1.1 Specifications, standards, and handbooks. The following specifica- tions, standards, and handbooks form a part of this doc;umentto the extent specified herein. Unless otherwise sp

6、ecified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-203 - A-A-50195 - A-A-50198 - A-A-50199 - V-B-871 V-F-106 DDD-L-20

7、PPP-B-636 MILITARY MIL-B-543 MIL-F-2 18, - o- MIL-L-35078 - MIL-W-43685 - MIL-T-43709 - MIL-T-44100 - MIL-C-83429 - STANDARDS FEDERAI; FED-STD-595 - FED-STD-751 - MILITARY MIL-STD-105 - Paper, Kraft, Untreated Thread, Aramid Thread, Gimp, Cotton, Buttonhole Thread, Polyester Core, Cotton- or Button,

8、 Sewing Hole, and Button, Staple, Fastener, Slide, Interlocking Label: For Clothing, Equipage, and Tentage, Boxes, Shipping, Fiberboard Polyester-Covered (Plastic) (General Use) Buckles, Tongueless and Web Strap Fastener Tapes, Hook and Loop, Synthetic Loads, Unit: Preparation of Semiperishable Subs

9、istence Items; Clothing, Personal EguipEnt and Equipage; General Specification For Webbing, Tape, Textile, Aramid Fiber Tape, Textile, Aramid Thread, Para-Aramid, Spun, Intermediate Modulus Cloth, Plain and Basket Weave, Aramid Colors Used in Govemnt Procurement Stitches, Seams, and Stitchings Sampl

10、ing Procedures and Tables for Inspection by Attributes 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-44372A 84 999990b 0493984 5 b c a MIL-T-44372A MIL-STD-129 - Marking for Shipent and Storage MIL-STD-147 - Palletized Unit InMds MIL-STD-73

11、1 - Quality of Wood Members for Containers and Pallets MIL-STD-1488 - Provisions for Evaluating Quality of Trousers (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Doc=uments Order Desk, Wiilding 4D, 700 Robb

12、ins Avenue, Philadelphia, PA 19111-5094.) * 2.2 Non-Government publications. this document to the extent specified herein. the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of dwments not listed in the DODISS are the i

13、ssues of the documents cited in the solicitation (see 6.2). The follming documents form a part of Unless otherwise specified, Unless otherwise specified, AMERICAN SOCIGTY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Comercial Packaging (Application for copies should be addressed t

14、o the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. documents also may be available in or through libraries or other

15、informa- tional services.) These 2.3 Order of precedence. In the event of a conflict between the text of Nothing in this document, hmever, supersedes applicable this document and the references cited herein, the text of this dwmeht takes precedence. laws and regulations unless a specific exemption h

16、as been obtained. 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Materials. It is encouragd that recycled material be used when practical as long as it meets the requirements of this specification. * 3.2.1 Ba

17、sic material. The basic material for class 1 trousers shall be plain weave aramid printed with a Woodland Camouflage Pattern conforming to type II, class 5 of MIL-C-83429. shall be plain weave aramid conforming to type II, class 6 of MIL-C-83429. The color for class 2 shall be Tan 380. The basic mat

18、erial for the class 2 trousers 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-44372A 4 W 999990b 0493985 7 MIL-T-44372A * 3.2.2 Material for side hanqinq poc kets, waistband lininq, riqht fly, and left flv. fly, and left fly shall be basic

19、material, ground shade cloth, or printed seconds cloth. conforming to class 5 of MIL-C-83429 prior to overprinting of the camouflage pttern. dimensional requirements of the respective finished fabric. Printed seconds shall be cloth which has been rejected only for defects pertaining to color, infrar

20、ed reflectance, or camouflage print patterns, cited in MIL-C-83429 for the class 1 trousers. The cloth for the side hanging pockets, waistband lining, right The cloth for class 1 shall be colored to a ground shade Ground shade cloth shall met the physical, mechanical, and * 3.2.3 Webbinq. to type I

21、of MIL-W-43685. for class 2 shall be Tan 380. The webbing for the waist adjustment straps shall conform The color for class 1 shall be Olive Green 106 and The width of the webbing shall be 5/8 inch. * 3.2.3.1 Tape, textile, aramid. 1/4 inch wide and shall conform to MIL-T-43709. be Olive Green 106 a

22、nd for class 2 shall be Tan 380. shall be seared or dipped in a colorless, noncombustible resin (see 6.5). tongueless, 2-bar conforming to type II, style 3, class 3, 5/8 inch of The tape for the leg drawcords shall be The color for class 1 shall Ends of the drawcords 3.2.4 Buckles. The buckles for t

23、he waist adjustment straps shall be MIL-B-543. * 3.2.5 Hook and loop fastener tape. be 1 inch in width and shall conform to type I, class 1, of MIL-F-21840. The color for class 1 shall be Olive Green 106 and for class 2 shall be Tan 380. The hook and loop fastener tape shall The colorfastness requir

24、ements shall not apply, * 3.2.6 Slide fastener. The slide fasteners listed belaw shall be brass with a black chemical finish and conform to type I, style 15, size MS of V-F-106. Slide fastener lenqths (inches) X-Small - Short X-Small - Regular Small - Short Small - Regular X-Small - Long Small - Lon

25、g Medium - Short Medium - Regular Medium - Long Large - Short Large - Regular 4 Lenqth 6-1/2 7 7-1/2 7 7-1/2 8 7-1/2 8 8-1/2 8 8-1/2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-44372A 84 = 9997706 0493986 9 MIL-T-44372A Slide fastener lenqt

26、hs (inches) (contd) Size Large - Long X-Large - Short X-Large - Regular X-Large - Long ienqth 9 8-1/2 9 9-1/2 * 3.2.6.1 Slide fastener tape. 3/4 inch wide and be of sufficient length to comply with the slide fastener attachment operation. The color for class 1 shall be Olive Green 106 and for class

27、2 shall be Tan 380. light and laundering qual to or better than the standard sample. When no standad sample is available, the tape shall show “fair“ fastness to light after six standard fading hours, and “good“ fastness to laundering. The slide fastener tape shall be aramid, 3 The finished tape shal

28、l show colorfastness to * 3.2.6.2 Slide fastener thonq, a thong of sufficient length to measure 2-1/2 to 3 inches (folded) when attached to slider pull tab. MIL-T-43709. shall be Tan 380. less, noncombustible resin (see 6.5). Each slide fastener shall be furnished with The thong shall be 1/4 inch wi

29、de, conforming to The color for class 1 shall be Olive Green 106 and for class 2 The thong shall be attached to slider Ends of the thong shall be seared or dipped in a color- puli tab as speclified in table I, okration 5. * 3.2.7 Button. The button for the waist closure shall conform to type II, cla

30、ss D, style 26, 30-line of V-B-871. The button shall have a dull finish. 9 The color for class 1 shall be Olive Green BP, Cable No. 62016 and for class 2 shall be Tan AJ, Cable No. 62028. * 3.2.8 Ghw. shall conform to type I or II, size No. 8 of A-A-50198, class 1 shall be Camouflage Green 483 appro

31、ximating color chip 34094 of FED-STD-595 and for class 2 shall be Tan 380. The cotton gimp for reinforcing the waist closure buttonhole The color for 3.2.9 Thread. * 3.2.9.1 Aramid and para-aramid. The thread shall be aramid, 40 and 60 tex conforming to A-A-50195. class 1 and size T-50 for class 2 c

32、onforming to MIL-T-44100 my be used as an alternate to aramid 40 and 60 tex. The color of the thread for class 1 shall be Camouflage Green 483 approximating color chip 34094 of FED-SITI-595 and for class 2 shall be Tan 380. The thread shall show fastness to laundering qual to or better than the stan

33、dard sample. thread shall show “good“ fastness to laundering. Para-aramid spun staple thread, size T-35 for When no standard is available, the * 3.2.9.2 Cotton-covered polyester core. Cotton-covered polyester core thread conforming to ticket No. 50, 2 ply of A-A-50199 my be used as an alternate thre

34、ad for bartacking. The color of the thread for class 1 shall 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-44372A 84 9999906 0493987 O = MIL-T-44372A be Camouflage Green 483 approximating color chip 34094 of FED-STD-595 and for class 2 shal

35、l be Tan 380 and shall Shaw fastness to laundering equal to or better than the standard sample. thread shall Shaw ttgoodtt fastness to laundering. When no standard sample is available, the P * 3.2.10 Labels. Each pair of trousers shall have an identification label, an instruction label, and a size l

36、abel or a combination identification and instruction label. belm. The color of the label for class 1 shall be Medium Green, Cable No. 70034, 70130, or 70131 and for class 2 shall be Khaki, Cable No. 70188. The fastness to laundering requirements of DDD-L-20 shall apply. * 3.2.10.1 Identification lab

37、el. The identification label shall conform to type VI, class 1 of DDD-L-20. * 3.2.10.2 Instruction label. VI, class 3 of DDD-L-20, The labels shall conform to the.requirements listed The instruction label shall conform to type The label shall contain the follawing information: TFCUSERS, AIRCREW, COM

38、BAT 1. 2. 3. Adjust waist size by straps on waistband. Blouse trousers outside of boots using drawcords. These trousers are of low flamnability. No other special flame ,-sistant treatment is required. 4. -/Machine Washinq: Permanent press cycle in warm water with a mild laundry detergent. 5. 6. Rins

39、inq: Rinse thoroughly in clear warm water after Do Ncrr SIARCH OR CHLORINE BLEACH, laundering. reduced. Detergent must be removed or fabric flame resistance will be 7. Dwing: Tumble dry at law heat (1309). Remove irmiediately WARNING Launder with slide fastener and hook and loop fasteners Do not pre

40、ss hook and loop fasteners. from dryer. To drip dry, remove from water and place on a rustproof hanger. engaged. Do Ncrr mw THIS LABEL * 3.2.10.3 Combination label. A combination identification and instruction label my be used. * 3.2.10.4 Size label. DDD-L-20. characters and shall contain the follow

41、ing infomtion, as applicable: It shall conform to tupe VI, class 15 of DDD-L-20. The size label shall conform to type VI, class 2 of The size information shall be printed with not less than 10 point 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

42、IL-T-VV372A 8V 9 9999906 0493988 2 9 MIL-T-44372A X-Small - Short X-11 - Reql X-sniall - Lonq Inseam: 26-1/2 to 29-1/2 inches Waist: p to 27 inches Stock No. NATO Size: 6775/5869 ISCKII: 29-1/2 to 32-1/2 inches Waist: p to 27 inches Stock No. NATO Size: 7583/5869 Ins-: 32-1/2 to 35-1/2 inches Waist:

43、 p to 27 inches Stock No. NAT Size: 8390/5869 Small - RWlm Small - mnq Small - Short Inseam: 26-1/2 to 29-1/2 inches Waist: From 27 to 31 inches Stock No. NAlD Size: 6775/6979 Inseam: 29-1/2 to 32-1/2 inches Waist: From 27 to 31 inches Stock No. NAT Size: 7583/6979 Inseam: 32-1/2 to 35-1/2 inches Wa

44、ist: From 27 to 31 inches Stock No. NA Size: 8390/69 t Medium - Short Medium - Reqular Medium - Long Inseam: 26-1/2 to 29-1/2 inches Waist: From 31 to 35 inches Stock No. NATO Size: 6775/7989 Inseam: 29-1/2 to 32-1/2 inches Waist: From 31 to 35 inches Stock No. NAT Size: 7583/7989 Inseam: 32-1/2 to

45、35-1/2 inches Waist: From 31 to 35 inches Stock No. NA Size: 8390/7989 arqe - Lonq Inseam: 32-1/2 to 35-1/2 inches Waist: From 35 to 39 inches Stock No. NATO Size: 8390/8999 Lame - Short arqe - Reqular Inseam: 26-1/2 to 29-1/2 inches Waist: From 35 to 39 inches Stock No. NATO Size: 6775/8999 Inseam:

46、 29-1/2 to 32-1/2 inches Waist: From 35 to 39 inches Stock No. NAlD Size: 7583/8999 X-Larqe - Short X-arqe - Reqular X-arqe - Lonq Inseam: 26-1/2 to 29-1/2 inches Waist: Above 39 inches Stock No. NATO Size: 6775/9909 Inseam: 29-1/2 to 32-1/2 inches Waist: Above 39 inches Stock No. NA Size: 7583/9909

47、 Inseam: 32-1/2 to 35-1/2 inches Waist: Above 39 inches Stock No. NAlD Size: 8390/9909 * 3.3 Desiqn. The trousers shall have a slide fastener fly closure. The trousers contain two cargo pockets, two calf patch pockets, two side hanging pockets, two hip pockets, and leg hem drawconis. hanging pockets

48、 contain flaps. pocket closures. Ail pockets except side Hook and loop fastener tape is used for all 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 -_ MIL-T-44372A 84 999990b 0493989 4 MIL-T-44372A 3.4 Fiaure. Figure 1 is furnished for infomtion

49、 only. To the extent of any inconsistencies between the figure and the specification, the specifica- tion shall control. 3.5 Patterns. Standard patterns, which provide a 1/2 + 1/8, -0 inch seam allawance for double-lapped and double-stitched seams and 3/8 f 1/8, -0 inch seam allawance for single needle seams, except where otherwise specified, will be furnished by the Government. altered in any way and are to be used