ARMY MIL-S-71146-1993 SIMULATOR LAUNCHING ANTI-TANK GUIDED MISSILE AND ROCKET M22 PARTS FOR AND LOADING ASSEMBLING AND PACKING《M22型火箭 反坦克导弹发射模拟器零件的装载 组装和包装》.pdf

《ARMY MIL-S-71146-1993 SIMULATOR LAUNCHING ANTI-TANK GUIDED MISSILE AND ROCKET M22 PARTS FOR AND LOADING ASSEMBLING AND PACKING《M22型火箭 反坦克导弹发射模拟器零件的装载 组装和包装》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-71146-1993 SIMULATOR LAUNCHING ANTI-TANK GUIDED MISSILE AND ROCKET M22 PARTS FOR AND LOADING ASSEMBLING AND PACKING《M22型火箭 反坦克导弹发射模拟器零件的装载 组装和包装》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、.d . flIL-S-71L4b m 9999906 1858345 339 m - Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document, should be addressed to: Commander U.S. Army ARDEC, ATTN: SMCAR-BAC-S, Picatinny Arsenal, New Jersey 07806-5000 by using the S

2、tandardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. INCH-POUND 1 MIL-S-71146 (AR) 21 June 1993 MILITARY SPECIFICATION Simulator, Launching, Anti-Tank, Guided Missile and Rocket M22 Parts for and Loading, Assembling and Packing This specific

3、ation is approved for use by the U.S. Army Armament, Munitions and Chemical command, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification contains requirements not covered by the drawings and provides quality assurance provisio

4、ns for the fabrication of parts for and loading, assembling and packing for one type of simulator designated as Simulator, Launching, Anti-Tank, Guided Missile and Rocket, M22 (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following s

5、pecifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in th

6、e solicitation (see 6.2). SPECIFICATIONS MI LI TARY MIL-E-116 - Preservation, Methods of MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification For Licensed by Information Handling ServicesNIL-S-7LL4b m 9999906 L5834b 275 = MIL-S-71146 (AR) STANDARDS MIL-STD-105 - Sam

7、pling Procedures and Tables for Inspection by Attributes MIL-STD-109 - Quality Assurance Terms and Definitions MIL-STD-331 - Fuze and Fuze Components, Environmental and Performance Tests For MIL-STD-1234 - Pyrotechnics, Sampling, Inspection and Testing MIL-STD-1235 - Single and Multi-Level Continous

8、 Sampling Procedure and Tables For Inspection By Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094). 2.1.2 Other Govern

9、ment documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS (see 6.6) US ARMY ARMAMENT RESEARCH, DEVE

10、LOPMENT AND ENGINEERING CENTER ( ARDEC) Product Drawings 12953563 - Simulator, Launching, Anti-Tank, Guided Missile and Rocket, M22 Packaging Drawings 9344296 - Packing and Marking for Box, Packing Wood Wire Bound, for Box Fiberboard, for Simu- lator, Launching, AT, GM and RKT, M22 9344297 - Packing

11、 and Marking for Box, Fiberboard, for Simulator, Launching, AT, GM and RKT, M22 Inspection Equipment Drawings 11749562 - Sirnulator, Antitank Missile Fire (Copies of other Government documents, drawings, and publications required by contractors in connection with specific acquisition functions shoul

12、d be obtained from the contracting activity or as directed by the contracting activity.) O 2 Licensed by Information Handling ServicesMIL-S-71146 999990b 1858347 101 MIL-S-71146 (AR) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein

13、, of this document takes precedence. however, supersedes applicable laws and regulations unless a specific exemption has been obtained. the text Nothing in this document, 3. REQUIREMENTS 3.1 Materials. Materiais and parts shall be in accordance with applicable drawings, specifications and standards.

14、 3.2 Assembly. The Simulator Assembly shall comply with all requirements specified on dwg. 12953563, and all associated drawings, and with all requirements specified in applicable specifications and standards. 3.2.1 Contact closure switch. The output end of the cartridge shall contain an electrical

15、contact strip (contact closure switch, Part Number 11749641). This strip shall have less than 1 ohm resistance when measured as specified in 4.5.5. 3.3. Moisture and volatile content. 3.3.1 Flash and bang. The moisture and volatile content of these compositions at the time of loading shall not excee

16、d 0.15 percent. 3.3.2 Paper and paper products. The moisture and volatile content of the paper and paper products components of the simulator assembly at the loading station at the time nof loading shall not exceed 6.0 percent. O 3.4 Functioning. (Ambient Temperature 21+3OC, 70+5OF, Hot 51.5+3OC, 12

17、5+5OF, Cold -32+3OC, -25+5OF). shall function and comply wrth the following requirements after conditioning at specified temperature. Theassembly 3.4.1 Sound characteristics. The sound level intensity of the cartridge functioning at a distance of 64 + 1.0 feet (ft.) from the simulator assembly shall

18、 be 134 +6 - 7 decibles (db) for a total duration of 15 milliseconds (ms) maximum (max), with a rise-time of 5 ms max. 3 Licensed by Information Handling ServicesMIL-S-71146 999990b 1858348 048 O 3.4.2 Functioning time. The time from application of nine plus or minus one (9 + 1) volts direct current

19、 (VDC), with no current limitations, to audible report of 3.4.1 of the assembly shall not be greater than 0.110 seconds. 3.4.3 Flash characteristics. The cartridge shall produce a visible flash when fired from a launch tube. This flash shall be a minimum (min) of six (6) feet in length, two (2) feet

20、 in width with a duration of 40 to 500 ms in winds of not more than 8 miles per hour. Residual smoke shall be white in appearance. 3.5 Leak test. The cartridge shall show no evidence of air or water leakage when tested as specified in 4.5.6. 3.6 Jumble. The simulator shall comply with the following

21、requirements. a. The simulator shall not function during test. b. There shall be no loose pyrotechnic powder on the simulator or in the test box after jumbling. c. The simulator components shall not separate during test. 3.7 First article. When specified in the contract or purchase order (see 6.3),

22、a sample shall be subjected to first article inspection in accordance with the technical provisions herein (see 4.3). O 3.8 Workmanship. All parts and assemblies shall be fabricated and finished in a thorough, workmanlike manner. They shall be free of burrs, chips, sharp edges, cracks, crazes, poros

23、ity, warpage, burn marks, blisters, excess flash, scratches, dirt, grease and other defects and foreign matter which would affect appearance or serviceability. The cleaning method used shall not be injurious to any part nor shall the parts be contaminated by the cleaning agent. All required markings

24、 shall be neat, legible and sharply defined. All packing components shall be dry. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examina

25、tions and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves th

26、e right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4 Licensed by Information Handling ServicesMIL-S-71146 W 999990b I1858349 T84 MIL-S-71146 (AR) 4.1.1 Responsibilit

27、y for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the cntractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contra

28、ctor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this do

29、es not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 General provisions. Unless otherwise specified herein, the provisions of MIL-A-48078 apply and form a part of this specification. Reference shall

30、 be made to MIL-STD-109 to define quality assurance terms used herein. 4.2 Classification of inspection. The inspection requirements specified herein are classified as follows: a. First Article Inspection. (See 4.3) b. Quality Conformance Inspection. (4.4) 4.3 First article inspection. 4.3.1 Submiss

31、ion. The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in . accordance with provisions of 4.3.2. The first article sample shall consist of the assemblies, components and test specimens listed below in the quantities indicated: Part Descriution

32、 Drawings Quantity Case 11749631 Tube 11749635 Closure, Switch 11749641 Closure 11749638 Disc, Separator 11749637 Pellet Assembly 117496 33 End Plate 11749632 Packing -w G -4 cn C 3- o a, VIP-FI I u (0 OE-4 03ido) ria x a, u-wo: I o) al + a 2 v) ci o) a, 4J o k Cu C al x m c, a, a ri .+ m w ci o) a,

33、 ci o) -4 .c ci k O ICC a, 4 a VI 5 1- m v 7 Licensed by Information Handling Services8 $2 (u a wcn aci -4 c ?a, wo E -4 “4 ia c 70 ap: I4 a -c ka O BEl -4 -4 Io z MIL-S-7LL4b 9999906 1858352 579 CJ rl (u v v I O P ri . -, v vv vq vvvvvv CJ (u (u0 m m mm mmmmmm h c, -4 cn cn ci u a, w a, a -k 4m o c

34、 19. o P -4 .44J $)Q u) ci u a, cec a, a -k NO mw u3 Ll a,“ C cec h a, k 7 4J rd k a, a Em cn au u ci -4 -4 8 r/l +J -4 C ? a, 3 O 2 C O a w O k! k a, a a, a O 4J 4J cn a, 4J x (d a, I4 5 - A Y Licensed by Information Handling ServicesMIL-S-7lL4b 9999906 1858353 405 m h cd O o I- V W + a O z !- 0 a

35、f O u) O Ln u) m h a, k 7 ci d k a, am v) Eu u a -4 -rl c,ci ci mm c, -4 -rl Ok k Ca al ci ci bkcik erb rb rlc Ca cuou o -4 ridcia bJcu(0 u7c4-0 c o 74 7mLir-u z-5 $ h a, k 7 ci rb k a, a c, 01 ciu C -4 a,ci -ri m Q -4 ci u rb tn asterisks indicates one hundred percent inspection. If sample size exc

36、eeds lot size, perform one hundred percent inspection. Accept on zero and reject on one or more for all inspection levels. 10 Licensed by Information Handling ServicesMIL-S-7LL4b 9999906 1858355 288 b. Alternative quality conformance provisions. Alternative quality conformance procedures, methods, o

37、r equipment, such as statistical process control, tool control, other types of sampling procedures, etc., may be used by contractor when they provide, as a minimum, the l.eve1 of quality assurance required by the provisions specified herein. Prior to applying such alternative procedures, methods, or

38、 equipment, the contractor shall describe them in a written proposal submitted to the Government for evaluation (see 6.2). When required, the contractor shall demonstrate that the effectiveness of each proposed alternative is equal to or better than the specified quality assurance provisions herein.

39、 In cases of dispute as to whether the contractors proposed alternative(s1 provides equivalent assurance, the provisions of this specification shall apply. All approved alternative provisions shall be specifically incorporated into the contractors quality program or detailed inspection system, as ap

40、plicable. 11 Licensed by Information Handling Services!? U W Pi vi z W U z a: z lx z O U H 2 ri LL O rl c w W I In a, cn m U 4 cv * * . . MIL-S-71l14b 999990b L85835b 114 w U z w Y IL W a n O I I- W W U z m E m Q n a, LL c O Ln c 3 D - P n E 3 - L O L 3 - 12 Licensed by Information Handling Services

41、MIL-S-71146 m 999990b 1858357 050 h G 4 Y W w 4 rl fi I m I d H c m u t- cn CY W t- u Q CY 6 I u LL O Z O I- 6 u u- cn cn A u - - - - - 6 LL O d t- W I u a, a I3 I3 NN NOD mm mm - nn mm au YY YY t- Lo Y c n O z c 0 I a, J 4 H H a, rl a m B a h Y % H H 4 a, a, LI % H H a, 4 a Licensed by Information

42、Handling Services4 k I; W I ui LI .?i I: - W U z W W U W a a o I t; 0 a z IT z U W ui 04 CO hl c u 4J 4 3 VI a, Li 5 o 00 ici rv MIL-S-711qb 9999906 1858358 T97 N“ oc) mm m nn n u Y Qt UV n X a E v A 4. Lix aJa -uE a,- a a, c -A a, 4 au rci c a, a a T3u .A 0 a, o 4 c um O z $4 a -4 c v) c r a, GI 4

43、H H aJ Il P a i3 u - Y 4 H H l-i a, aJ J 4 H H a, rl a t3 Q n h Y 4 H rl a, a, cl 4 H H a, l-i a I3 n ui uh i2 - 14 Licensed by Information Handling ServicesMIL-S-7LL4b = 9999906 1858359 923 rl U O rl c w W I v) a, LI 3 Lo O :rl W u z Y W U. W a a n O I I- W E: z I- U W ln 0 n 5 + v) W I- LI O “hlw

44、W mmmm m 15 Licensed by Information Handling Servicesri LL O 4 W I v) Li -no E Li O U m Li m QI a, VI V :Fi 4 -5: Li ori O4 CO lari -AN c - W V z W LL w w a o O I !i t z I- V W v) 0 n z MIL-S-31146 W 9999906 1858360 b45 W rl a a, 3 m o a .d u 3 (v 00 m m . . h h a Q Y Y 5 a, r: -4 w Li a, a, U a, a,

45、 E E (0 O -FI z n a .FI c o c a io a, w- I- 34 21 Licensed by Information Handling Servicesz O E4 U w pt cn z H w U z 4 p: z O U i E-c LI 4 3 oi H E H MIL-S-3LLYb 999990b L8583bb Ob3 +- a, I4 4 H H Q, 4 Q a E-i u h Y 4 H H ri a, a, l=l 4 H H a, 1 P a E Q - 4 4 -I i a, a, J 4 I 4 u i 1 a E-i a n Y Y

46、3 - J . 22 Licensed by Information Handling Servicesz O E u W n4 v) z H W u z 4 E !x O H E * E IA 4: 3 a H 4 o d c w u1 I rn MIL-S-7L146 m 9999906 1858367 TTT m (UN (um mm mm d 1 O .CI hh o(d QV I+- Y- c in W t a 0 5 O z I- -? E x W oi (d au O cc O Li u0 o ou Liu Lia, OLi uLl a CO a, ad u c C -4 4 -

47、4 W (d a, am a cnc a, ur c aLi O aa z xz -4 H 4 a, a, !4 . H H a, 4 i1 (d E+ u h Y . H H H t-4 a, a, !4 . H H a, d a (d e a h Y . H H d a, a, J . H H a, 4 a m w h mm w t O 23 Licensed by Information Handling ServicesMIL-S-71146 = 9999906 1858368 936 = I+ m u z O E U W ch m z H H 4 m & W V z 4 r: p:

48、O cri z O V “I E H 4 4 3 0 a O t c v) w c O z c a 0 z Q r X w mw Ca, I *FI x I W a, c -4 rci a, 5 a, c O z Li OiO c3 u0 ao E& + H -i a, a, 4 h H H a, 4 Q a A u Y b H H H 4 a, 3 a, cil - H H a, l-i Q a E Q h v h H H n v)Y w c a 9 I 24 Licensed by Information Handling Services- MIL-S-71146 m 9999906 1

49、858369 872 m MIL-S-71146 (AR) 4.4.3 Testing. 4.4.3.1 Moisture content (see Table III) - Major Defects. TABLE III Flash and bang Paper and paper products See 3.3.1 See 3.3.2 The contractor shall provide adequate controls to insure that the material comply with the requirements. For verification, the contractor shall select and subject to test, one sample of each material from each eight(8) hours production. If a composite sample exceeds the requirement, that quantity or sub-lot material represented by the sample shall not be used in loading and packing, the remaining