ARMY MIL-S-62317 A-1982 SEMITRAILER TANK AIRCRAFT REFUELING 5 000 GALLON TURBINE FUEL AND AVIATION GASOLINE COMMERCIAL《商用油箱可装5 000加仑汽轮机燃料和航空汽油 空中加油机的半拖车》.pdf

《ARMY MIL-S-62317 A-1982 SEMITRAILER TANK AIRCRAFT REFUELING 5 000 GALLON TURBINE FUEL AND AVIATION GASOLINE COMMERCIAL《商用油箱可装5 000加仑汽轮机燃料和航空汽油 空中加油机的半拖车》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-62317 A-1982 SEMITRAILER TANK AIRCRAFT REFUELING 5 000 GALLON TURBINE FUEL AND AVIATION GASOLINE COMMERCIAL《商用油箱可装5 000加仑汽轮机燃料和航空汽油 空中加油机的半拖车》.pdf（43页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-S-62337A 23 m 7997706 0202532 3 m Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: DRSTA-GBS.l, Warren, MI 48090, by using the self-addressed Standardi

2、zation Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. 23 April 1982 SUPERSEDING MIL-S-62317(AT) 11 July 1979 MILITARY SPECIFICATION SEMITRAILER, TANK: AIRCRAFT REFUELING, 5,000 GALLON, TURBINE FUEL AND AVIATION GASOLINE, COMMERCIAL This specification

3、 is approved for use by the US Army Tank- Automotive Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers two types of 5,000 gallon, tandem axle, aircraft fuel servicing tank semitrailers

4、 with a 300-or 600 gallon per minute (gpm) fuel servicing rate. Vehicles procured under this specification are commercial items which shall be warranted by the manufacturer as specified in the procurement documents. * 1.2 Classification. The semitrailer shall be one of the following types, as specif

5、ied (see 6.2): Type I Type II - 600 gpm refueling rate. - 300 gpm refueling rate 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. Unless otherwise specified, the following specifications, standards, and handbooks of the issue listed in that issue of t

6、he Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this specification to the extent specified herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FEDERAL O-E-915 - Extinguisher, Fi

7、re, Dry-Chemical, (Hand-Portable) . MI LITAY MIL-G-5572 MIL-T-5624 MI L-N-5 8 7 7 MI L-A- 8 6 2 5 MI L-F-8 9 O 1 MIL-C-10387 MIL-P-10388 MI L-A-2 7302 MIL-C-2 7487 MIL-F-52308 MI IrN-5 27 47 MIL-M-81380 MIL-C-83413 MIGN-87963 - Gasoline, Aviation, Grades 80/87, 100/130, - Turbine Fuel, Aviation, Gra

8、des JP-4 and - Nozzle, Pressure Fuel Servicing, Locking, - Anodic Coatings, for Aluminum and Aluminum - Filter-Separators, Liquid Fuel: and 115/145. JP-5 Type D-1, Nominal 2 1/2 Inch Diameter. Alloys Filter-Coalescer Elements, Fluid Pressure: Inspection Requirements and Test Procedures For. - Coupln

9、g, Clamp Pipe, with Bolts and Synthetic Rubber Gasket, for Grooved Pipe and Tube. - Pipe Fitting, One or More Ends Grooved. - Arrester, Spark, Exhaust, Internal - Coupling Halves, Quick-Disconnect, Cam- - Filter Element, Fluid Pressure. - Nozzle Assembly, Closed-Circuit Refueling. - Monitor, Contami

10、nation, Fuel Dispensing - Connector, Electric1 Ground. - Nozzle: Fuel, Aircraft, Overwing: Type Combustion Engine. bcking Type. Sy s tem. MD-3. STANDARDS FEDERAL FED. STD. No. 595 - Colors. MILITARY MIGSTD-1223 - Non-Tactical Wheeled Vehicles Treatment, Painting, Rustproofing, Identification Marking

11、 and Data Plate Standards. MS75021 - Connector, Receptacle, Electrical - 12 Contact, Intervehicular, 24-V01t, 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-S-62317A 23 7777706 02025111 5 * 2.1.2 Other Government documents, drawings, and publi

12、cations. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. Regulations Governing Transportation of

13、 Dangerous Articles in Tank Motor Vehicles (49 CFR 178). (Application for copies should be addressed to the Department of Transportation, Federal Highway Administration, Washington, D.C. 20591 a) i ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor V

14、ehicle Engines. Noise Emission Standards for Transportation Equipment - Medium and Heavy Trucks. (Application for copies should reference the Code of Federal Regulations, 40 CFR, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Was

15、hington, D.C. 20402.) NATIONAL BUREAU OF STANDARDS Handbook 44 - Specifications and Regulations for Commercial Weighing and Measuring Devices. (Application for copies should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402 . ) (Copies of specif

16、ications, standards, handbooks, drawings, and publications required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) * 2.2 Other publications. The following document(s) form a part of this

17、specification to the extent specified herein. documents which are indicated as Don adopted shall be the issue listed in the current DoDISS and the supplement thereto, if applicable. The issues of the 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

18、AMERICAN PETROLEUM INSTITUTE (API) RP 1004 - Bottom Loading and Vapor Recovery for MC306 Tank RP 2003 - Recommended Practice for Protection Against Ignitions Motor Vehicles. Arising out of Static, Lightning and Stray Currents. (Application for copies should be addressed to the American Petroleum Ins

19、titute, 2101 L Street, N.W., Washington, D.C. 20037.) AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) Boilers and Pressure Vessel Code - Section VIII. (Application for copies should be addressed to the American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017.) NATIONAL FIRE

20、 PROTECTION ASSOCIATION (NIPPA) NFPA No. 407 - Aircraft Fuel Servicing 1980. (Application for copies should be addressed to National Fire Protection Association, 470 Atlantic Avenue, Boston, MA 02110.) SAE, INC. SAE Standards and Recommended Practices. 5318 - Airbrake Gladhand Service (Control) and

21、Emergency (Supply) Line Couplers - Trucks, Truck-Tractors, and Trailers. Radio Interference Characteristics of Vehicles and Devices (20-1000 MHz) (DoD adopted). 5552 - External Electromagnetic Radiation Suppressors. 5560 - Seven-Conductor Electrical Connector for Truck-Trailer Jumper Cable. 5588 - T

22、urn Signal Lamps. 5682 - Rear Wheel Splash and Stone Throw 5700 - Fifth Wheel Kingpin - Commercial 5702 - Brake and Electrical Connection 5551 - Limits and Methods of Measurement of Protection. Trailers and Semitrailers. Locations - Truck-Tractor and Truck-Trailer. (Application for copies should be

23、addresse.d to SAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-62317A 23 m 7777706 0202516 7 m STATE OF CALIFORNIA Air Resources Board Executive Order G-70-10-A (Application for copies

24、should be addressed to the Air Resources Board, 1102 Q Street, P.O. Box 2815, Sacramento, CA 95812.) THE TIRE AND RIM ASSOCIATION, INC. Yearbook. (Application for copies should be addressed to the Tire and Rim Association, Inc., 3200 W. Market Street, Akron, OH 44313.) (Industry association specific

25、ations and standards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) * 2.3 Order of precedence. Except as otherwise specified herein, in the event of a conflict between the text of this specification and the referenc

26、es cited herein, the text of this specification shall take precedence. 3. REQUIREMENTS 3.1 Standard semitrailer, components, and accessories. Except as specified in 3 1.1 through 3.1.1.4, the semitrailer, components, and accessories shall be standard or optional items which meet or exceed the requir

27、ements of this specification. and rated in the manufacturers technical data, including special or mounted equipment. Technical data shall be limited to specifications and techriical material, identical to that furnished to the authorized company representatives for selection of semitrailer models an

28、d components, and shall be on file in the engineering offices of the procuring activity, prior to delivery of the items. The semitrailer and furnished accessories shall comply with all Federal Motor Vehicle Safety Standards in effect on the date of manufacture. All items shall be as represented . 3.

29、1.1 Special requirements. In addition to the standard semitrailer and components specified in 3.1, the semitrailer shall be furnished with special equipment as specified herein. * 3.1.1.1 Painting and marking. As specified by the procuring activity for the appropriate service (see 6.2), treatment, p

30、ainting, -identification marking and data plates shall be in accordance with MIGSTD-1223 except the exterior color shall be gloss yellow, matching color chip No. 13538 of FED. STD. No. 595. In addition, the vehicle body shall be marked in accordance with paragraphs 4-11 through 4-11.2 Of NFPA NO. 40

31、7. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-62337A 23 9999906 OZOZ537 O E * 3.1.1.2 Rustproofing. When specified (see 6.2), the vehicle shall be rustproofed in accordance with MIL-STD-1223. When specified, (see 6.2), tropical rustproof

32、ing in accordance with MIGSTD-1223 shall be furnished. 3.1.1.3 Radio interference suppression. The vehicle shall be suppressed to limit electromagnetic radiation in accordance with SAE 5551. Suppressors used shall conform to SAE 5552. 3.1.1.4 Drain plugs. All drain plugs installed throughout the veh

33、icle for the purpose of draining lubricants shall be of the permanent magnet type. 3.2 Weights, loads and dimensions. 3.2.1 Net weight. The net weight of the fully equipped semitrailer shall be the minimum practicable for the service intended. * 3.2.2 Rated payload capacity. The rated payload capaci

34、ty shall be not less than the weight computed from the rated liquid capacity (5,000 gallons), using 6.8 pounds per gallon for the product (turbine fuel). , 3.2.3 Gross weight. The gross weight shall consist of the net weight and the payload. * 3.2.4 Weight distribution, bad bearing members of the se

35、mitrailer shall be rated for the loads imposed with the tank filled to nominal capacity, and a maximum tank slope of 1 percent to the rear. * 3.2.5 Dimensions and clearances. The semitrailer, uncoupled from the towing vehicle, resting level on the landing legs, without payload, and on level ground,

36、shall conform to the dimensions speciffed in table I. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-62317A 23 m 797770b O202538 2 m Overall width (maximum) Overall height (maximum) Minimum swing clearance (radius from center of the kingpin

37、to any point 6 inches below upper fifth.whee1 plate) (not less than) Swing radius from the centerline of the kingpin to the most distant point on the semitrailer nose (not more than) Distance from the centerline of kingpin to front end of the semitrailer (not more than) Upper fifth wheel height (plu

38、s or minus one inch) Ground clearance (not less than) Landing leg ground clearance (not less than) c 96 105 82 56 36 48 10 11 TABTJI I. Dimensions and clearances. Characteristic 1 Inches- 1 Overall length (maximum) I 384 3.3 Performance requirements. * 3.3.1 Functional performance. The semitrailer s

39、hall be capable of transporting 5,000 gallons of aircraft turbine fuel and shall be capable of performing the fuel servicing functions specified in 3.6.14.3. The semitrailer shall be capable of all fuel transfer functions while either connected to or separated from the towing vehicle. * 3.3.2 Mobili

40、ty performance. The semitrailer, fully equipped and loaded with the rated payload, shall be capable of being towed at speeds of not less than 10 miles per hour (mph) over unimproved roads (see 6.3), and over reasonably hard uneven terrain, and of being towed at speeds of not less than 55 mph over im

41、proved roads. 3.3.2.1 Turning ability. The semitrailer shall be capable of passing through a 90 degree angle to the towing vehicle without cramping or damage to the semitrailer or the towing vehicle. 3.3.2 Tracking ability. The Semitrailer shall conform to the tracking ability requirements of Federa

42、l Motor Carrier Safety Regulation 393.70(a). * 3.3.2.3 Brake performance, The service brakes shall stop the semitrailer-tractor combination, with the semitrailer loaded with specified payload, within the stopping distance requirements of Federal Motor Carrier Safety Regulation 393.52. 7 Provided by

43、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4 Chassis components. 3.4.1 Chassis. The chassis frame shall consist of the tank shell (with its internal bulkheads) as the primary frame member, with welded external longitudinal members connected by crossmember

44、s distributing concentrated loads into the shell. accordance with 49 CFR, sections 178.340 and 178.341. structure shall support the payload and provide attachment for the upper fifth wheel plate and kingpin, suspension system, landing gear, underslung cabinets, and associated piping and accessories.

45、 All structural design shall be in The primary tank 3.4.2 Suspension system. The semitrailer shall be furnished with the manufacturers standard suspension system. suspension system shall have a rated capacity at least equal to the load imposed, measured at the wheels at the ground, when the semitrai

46、ler is loaded with its rated payload (see 3.2.2). interference betweenwheels and with any other part of the semitrailer under the operating conditions specified herein. Each component of the Clearance shall preclude 3.4.3 Tandem axles. Tandem axles shall be furnished. Axle ratings shall be at least

47、equal to the load imposed on each axle, measured at the ground, when the semitrailer is loaded with the rated payload. The wheel bearings and axle spindles shall be oil lubricated. The oil viscosity shall be in accordance with the manufacturers recommendations. The hub caps shall have a window for v

48、isual determination of the oil level. Provision for venting, or other method of withstanding internal pressure buildup, and for replenishing the oil supply, shall be incorporated. The hubs shall be fitted with seals. * 3.4.4 Wheels, rims, tires and tubes. The semitrailer shall be equipped with dual

49、wheels on each axle. Rim and tire ratings shall conform to Tire and Rim Association recommendations for the type and size of tires furnished. Rim sizes shall be the same for all wheels on the semitrailer. Tire size and load range (ply rating) shall be the same for all tires on the semitrailer. When specified (see 6.2), disc type wheels shall be furnished. * 3.4.4.1 Tires. Tires shall be tube or tubeless type with highway tread. speci