ARMY MIL-PRF-32062-2000 CASE CARRYING FOR M198 M119 FIRE CONTROL OPTICS《M198 M119 射击指挥光学系统运行用容器》.pdf

《ARMY MIL-PRF-32062-2000 CASE CARRYING FOR M198 M119 FIRE CONTROL OPTICS《M198 M119 射击指挥光学系统运行用容器》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-PRF-32062-2000 CASE CARRYING FOR M198 M119 FIRE CONTROL OPTICS《M198 M119 射击指挥光学系统运行用容器》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH POUND MIL-PRF-32062(AR) 15 March 2000 PERFORMANCE SPECIFICATION Case, Carrying for M198/M119 Fire Control Optics This specification is approved for use by the U.S. Army Armament Research, Development and Engineering Center, and is available for use by all Departments and Agencies of the Depart

2、ment of Defense. 1. SCOPE 1.1 Scope. This specification is for a type of carrying case, designated as Case, Carrying for M198/M119 Fire Control Optics (See 6.1). 1.2 Classification. Items covered by this specification should be of the following: Type I Carrying Case, Fire Control for M198 Type II Ca

3、rrying Case, Fire Control for M119 2. APPLICABLE DOCUMENTS. 2.1 General. The documents listed in this section are specified in Sections 3 and 4 of this specification. This does not include documents cited in other sections of this specification or recommended for additional information or as example

4、s. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all the requirements as cited in Section 3 and 4 of this specification, whether or not they are listed. Beneficial comments (recommendations, additions, deletions) and any pe

5、rtinent data which may be of use in improving this document, should be addressed to: Commander, U.S. Army TACOM-ARDEC, ATTN: AMSTA-AR-QAW-E, Picatinny Arsenal, New Jersey 07806-5000 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by

6、letter. AMSC N/A FSC:1240 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MIL-PRF-32062 (AR) 2 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. T

7、he following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issue of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto

8、, cited in the solicitation (see 6.2). SPECIFICATIONS A-A-59136 Packaging Material, Plank STANDARDS FEDERAL FED-STD-595 Colors Used in Government Procurement DEPARTMENT OF DEFENSE MIL-STD-810 Environmental Test Methods and Engineering Guidelines MIL-STD-1916 DoD Preferred Methods for Acceptance of P

9、roduct (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094 or http:/assist.daps.mil/online/login/login.cfm.) . 2.2.2 Other Government docume

10、nts. The following other Government documents, drawings, and publications, form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation. DRAWINGS US ARMY ARMAMENTS RESEARCH, DEVELOPMENT AND ENGINEERING CENT

11、ER (ARDEC) 11731008 - Plate 12994172 - Plate Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MIL-PRF-32062 (AR) 3 12994171 - Insert, Cover 12994170 - Insert, Body 12994169 - Insert, Cover 12994168 - Insert, Body 12994167 - Plate (Copies of other Govern

12、ment documents, drawings, and publications required by contractors in connection with specific acquisition functions should be obtained from the U.S. Army TACOM-ARDEC, AMSTA-AR-QAD, Picatinny Arsenal, NJ 07806-5000) 2.3 Order of precedence. In the event of a conflict between the text of this documen

13、t and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), in the contract, a sample shall be

14、subjected to first article inspection in accordance with 4.1. 3.2 Design, materials, and manufacturing processes. Unless otherwise specified, the design, materials, and manufacturing process selection is the prerogative of the contractor as long as all articles submitted to the Government fully meet

15、 the functional and operating requirements specified. 3.3 Operating requirements. Each carrying case shall provide the following functional, operational, and performance capabilities. 3.3.1 Color. The carrying case shall be a uniformly non-reflective forest green color, chip #34079 of FED-STD-595. 3

16、.3.2 Ease of use. All types of cases shall have the following features to accommodate user needs: a. A means of releasing internal pressure (by a person wearing MOPP IV gloves) to allow ease of opening following changes in altitude. b. One handle on the top (latch side) of the case to enable ease of

17、 stowage and removal from the rack on the howitzer, as well as ease in transport by a single person wearing cold weather protective gloves. c. Closures shall ensure ease in opening and closing by a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MIL-PR

18、F-32062 (AR) 4 single person wearing cold weather protective gloves, while providing sufficient force to meet sealing requirements. d. The cover and lid shall be connected with a hinge to allow easy removal and placement of items in case. Top and bottom of case must remain attached when opened. 3.3.

19、3 Marking. Each carrying case shall have the markings respective to the part number specified in the solicitation as indicated in Table I. The markings shall be externally applied by any method commonly used by the contractor in contrasting colors relative to the background color. The case and marki

20、ngs shall not become discolored, degraded, or illegible throughout all phases of the verification testing. The “ID MARKINGS” letter height shall be a minimum of 1.0 inches and located across the flat of the cover. Identification of the case cover shall be designated by arrows and “UP” to identify th

21、e orientation of the case. Table I. Marking requirements DESCRIPTION TYPE I TYPE II ID MARKINGS CASE, CARRYING P/N MIL-PRF-32062, TYPE I CASE, CARRYING P/N MIL-PRF-32062, TYPE II 3.4 Interface requirements. Each carrying case shall meet the following requirements. 3.4.1 Weight. The carrying case sha

22、ll weigh no more than 20 pounds. 3.4.2 Physical dimensions. 3.4.2.1 Type I. The carrying case shall have minimum outside dimensions of 20.0 inches in width by 8.5 inches in height by 20.0 inches in length and maximum outside dimensions of 20.38 inches width by 8.7 inches height by 21.0 inches in len

23、gth. 3.4.2.2 Type II. The carrying case shall have minimum outside dimensions of 20.0 inches in width by 8.5 inches in height by 20.0 inches in length and maximum outside dimensions of 25.0 inches width by 11.0 inches height by 25.0 inches in length. 3.4.3 Cushion inserts. The inside dimensions of t

24、he carrying case shall accommodate the cushion inserts for each type case in the locations shown on the respective figure. The outside dimensions of the cushions shall be consistent with the inside dimensions of the case to ensure a tight fit in the case shell. The cushioning material shall conform

25、to A-A-59136, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MIL-PRF-32062 (AR) 5 Packaging Material, Sheet, and the applicable drawing requirements. The cushions must be secured to the interior of the case by means commonly utilized by the contractor

26、 which will resist removal by pulling. a. Type I: Insert, Cover 12994171 Insert, Body 12994170 Location Figure 1 b. Type II: Insert, Cover 12994169 Insert, Body 12994168 Location Figure 2 3.4.4 Identification plates. The case cushions and exterior shall accommodate the ID Plates listed in Table II i

27、n the locations as shown in Figure 1 for Type I and Figure 2 for Type II. The plates shall be adhered to the case shell by any means normally utilized by the contractor, which will remain intact throughout case operations at all temperature extremes. Table II: Identification plates TYPE I TYPE II SP

28、ECIAL WARNING MARKINGS Plate-11731008-7 Plate-11731008-5 INSTRUCTION PLATES Plate-12994172 Plate-12994167 3.5 Ownership and support requirements. Each carrying case shall possess the following life cycle ownership characteristics. 3.5.1 Safety. Each carrying case shall present no physical handling h

29、azards, such as sharp protrusions, to the persons using them. 3.6 Operating environment requirements. Each carrying case shall operate under and after exposure to the following environmental conditions without damage or loss of performance. 3.6.1 Temperature. At low temperatures down to 40oF. At hig

30、h temperatures up to +150oF. 3.6.2 Drop. The carrying case shall not suffer damage or loss of performance after 3 drops from a height of four (4) feet onto a smooth concrete surface with a load as specified in 4.7.3. 3.6.3 Waterproofness. The carrying case shall not leak when submerged in water for

31、one hour with the water level 0.5 to Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MIL-PRF-32062 (AR) 6 3.0 inches above the upper surface of the carrying case. 3.6.4 Fungus resistance. The carrying case shall show no evidence of damage, deterioratio

32、n or profuse growth when subjected to the tests outlined in 4.6.5. 4. VERIFICATION Table III: Requirement/verification cross reference matrix Methods of Verification Classes of Verification N/A -Not Applicable A - First article 1 - Analysis B - Conformance acceptance 2 - Demonstration 3 - Examinatio

33、n 4 - Test Section 3 Requirements Verification Methods Verification Section 4 Verification Verification Levels NA 1 2 3 4 A B 3.1 X 4.2 3.2 X 3.3 X 3.3.1 X X X 4.4.1 I 3.3.2 X X X 4.4.2 I 3.3.3 X X X 4.4.3 I 3.4 X 3.4.1 X X X 4.5.1 I 3.4.2 X X X 4.5.2 II 3.4.3 X X X 4.5.3 II 3.4.4 X X X 4.5.4 I 3.5

34、X 3.5.1 X X X 4.6.1 I 3.6 X 3.6.1 X X 4.7.1 and 4.7.2 3.6.2 X X 4.7.3 3.6.3 X X X 4.7.4 II 3.6.4 X X 4.7.5 4.1 Classification of inspections. Inspection requirements are classified as follows: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MIL-PRF-320

35、62 (AR) 7 a. First article inspection (see 4.2). b. Conformance inspection (see 4.3). 4.1.1 Verification conditions. Unless otherwise specified, all inspections shall be performed in accordance with the test conditions specified. 4.1.2 Classification of characteristics. For examinations and tests ci

36、ted herein or when required by the contract, critical, major, and minor characteristics are defined in Section 3 of MIL-STD-1916. 4.2 First article inspection. When specified in the contract, a sample of the carrying case shall be subjected to first article verification in accordance with Table III.

37、 4.2.1 First article quantity. First article verification shall be performed on three carrying cases. 4.2.2 Inspections to be performed. As determined by the Government, the first article assemblies, components and test specimens shall be subjected to any or all of the examinations and tests specifi

38、ed in this specification and be inspected for compliance with any or all requirements of the specification and the applicable drawings. 4.2.3 First article rejection. If any assembly, components or test specimen fails to comply with any of the applicable requirements, the first article sample shall

39、be rejected. The Government reserves the right to terminate inspection upon any failure of an assembly, component or test specimens to comply with any of the requirements. 4.3 Conformance verification. Sampling for conformance verification shall be in accordance with MIL-STD-1916. The sample shall m

40、eet the conformance inspection tests as specified in Table III. Unless otherwise specified in the contract, the item shall be returned to the lot after successful completion of testing. If the conditions stated are not met, the lot shall be rejected. 4.4 Operating verification. 4.4.1 Color. The exte

41、rior surfaces of the carrying case shall be visually examined compared to color chip 34079 of FED-STD-595 to verify that the color is uniform forest green. 4.4.2 Ease of use. The operator shall be wearing cold Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

42、IHS-,-MIL-PRF-32062 (AR) 8 weather protective gloves (on both hands). Lay the case flat, open and close the case a minimum of five times. The case shall open and close freely without binding. The latch shall be moved from the closed to open to closed position without binding. Pick up the case by the

43、 handle. The handle shall be securely attached to the case in that there shall be no visible space between the handle and the case at the mating junctures. The case material shall show no evidence of delamination, distortion, cracking or bubbling following the test. 4.4.3 Marking. The case shall be

44、visually inspected to verify all marking conditions. The markings shall remain unblemished throughout the operational requirements testing of 4.5. 4.5 Interface verification. 4.5.1 Weight verification. Case shall be weighed on a commercial scale. Weight of each case is to be no more than 20 lbs. 4.5

45、.2 Dimension verification. The external dimensions of the carrying case shall be measured and shall not exceed the dimensions specified in 3.4.2. 4.5.3 Cushion insert verification. The cavities of each cushion insert shall be measured to ensure compliance with the conditions of 3.4.3. The case shall

46、 be grasped by the cushion and lifted to ensure security. The test will be performed by personnel meeting the 95 percentile male or 5 percentile female soldier. 4.5.4 Identification plate verification. The location and inscriptions of the identification plates shall be visually examined to ensure co

47、mpliance with the conditions of 3.4.4. 4.6 Ownership and support verification. 4.6.1 Safety verification. Inspect the carrying case to be free of hazardous burrs, cracks, deformation, distortion, disconnects, rings, bulges, or sharp edges that would prevent proper seating alignment, engagement, or a

48、ssembly of pallet components, posing physical danger to the operator or equipment. 4.7 Operating environment verification. Each case to be tested will be exposed to all tests from this section. All cases shall be tested for proper functioning and inspected for damages prior to starting tests. Provid

49、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MIL-PRF-32062 (AR) 9 4.7.1 Low temperature. Subject a case to air temperature of 40F for a period of one hour after internal temperature stabilization of the test item. At the end of the one hour period, while the case is at the 4