ARMY MIL-P-48077-1972 PRIMER M104 PARTS FOR AND LOADING ASSEMBLING AND PACKING《M104式引物零件及其装药 组装和包装》.pdf
《ARMY MIL-P-48077-1972 PRIMER M104 PARTS FOR AND LOADING ASSEMBLING AND PACKING《M104式引物零件及其装药 组装和包装》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-P-48077-1972 PRIMER M104 PARTS FOR AND LOADING ASSEMBLING AND PACKING《M104式引物零件及其装药 组装和包装》.pdf(19页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-P-48077 (MU) 26 June 1972 SUPERSEDING (See 6.8) MILITARY SPECIFICATION PRIMER: M104 , PARTS FOR AND LOADING, ASSEMBLING AND PACKING 1. SCOPE 1.1 This specification covers the parts, and the load- ing, assembling and packing for one type of primer designated as Primer: M104. 2. APPLICABLE DOCUMEN
2、TS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL L-P-403 - Plastic Molding Material Polytetra Fluoroethylene ( TFE-Fluorocarbon) MILITARY MIL-A-2550 -
3、 Ammunition and Special Weapons, General Speci- fication for MIL-1-45607 - Inspection Equipment, Acquisition, Maintenance and Disposition of P- A THIS DOCUMENT CONTAINS 19 PAGES. ?* - 0 Licensed by Information Handling Services_c MIL-P-48077 13 0b 03Lb03b b M . MIL-P-48077 (MU) STANDARDS MILITARY Sa
4、mpling Procedures and Tables for Inspection by Attributes- (ABC-STD-105) - MIL-STD-105 Quality Assurance Terms and Definitions - MIL-STD-109 MIL-STD-1168 - Lot Numbering of Ammuni- tion Single and Multilevel Continuous Sampling Pro- cedures and Tables for - MIL-STD-1235 - Inspect ion by Attributes D
5、RAWINGS U. S. ARMY MUNITIONS COMMAND C-8864967 Primer, M104 Box, Set-up, .Packing Ammunition, Inner, for Small Explosive Compon- ents (2 SHTS) - F-9258182 Box, Set-up, Packing, Ammunition, Outer, for Small Explosive Compon- ents (2 SHTS) - C-9258183 C-9258184 - Box, Packing, Ammunition, for Small Ex
6、plosive com- ponents (2 SHTS) PUBLICATIONS ARMY ET-8864967 Equipment Tabulation (Copies of specifications, standards, drawings and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the Contracting Off
7、icer.) Licensed by Information Handling ServicesMIL-P-48077 (MU) 2.2 Other publications.-The following documents form a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on the date of invitation for bids or request for proposal shall apply. C
8、ODE OF FEDERAL REGULATIONS Title 49 - Transportation, Parts 0-190 (The Code of Federal Regulations is available from the Superin- tendent of Documents, U. S. Government Printing Office, Washington, D. C. 20402. Orders should specify, “49 CFR 0-190 (latest revision) “ . ) 3. REQUIREMENTS 3.1 Material
9、s.-Materials and parts shall be in accordance with applicable drawings and specifications. 3.2 Primer.-The primer shall comply with all requirements specified on Drawing (Dwg.) C-8864967, all associated drawings, and with all requirements specified in applicable specifications. 3.3 Moisture content
10、of priming mixture.-The moisture con- tent of priming mixture at the time of loading shall be less than 0.50 percent when tested as specified in 4.4.1. 3.4 Moisture content of lead azide.-The moisture content of the lead azide increment at the time of loading shall be less than 0.30 percent when tes
11、ted as specified in 4.4.2. attempt under the impact of a two (2)-ounce ball falling a distance of four (4) inches, maximum, when tested as specified in 4.4.3. 3.5 Functioning.-The primer shall function on the first 3.6 Output.-The explosive output shall indent the spedi- fied disc to a depth of 0.12
12、5 inch, minimum, when tested as specified in 4.4.3. 3.7 Adherewe of-primers to packaging.-The .pr.imers shall not stick to theXeleaSe Paper or spacer in-the inner sqt-ug box when inspected as specified in 4.4.4. 3.8 Workmanship.-All parts and assemblies shall be fabri- cated, loaded and assembled in
13、 a thorough, workmanlike manner. They shall be free of burrs, sharp edges, cracks, surface defects, dirt, grease, rust, and other foreign matter. The cleaning method shall not be injurious to any part., nor shall the parts be con- taminated by the cleaning agents. Exterior surface coatings shall be
14、continuous except for afew light scratches not exposing base material. All required markings shall be neat and sharply defined. 3 Licensed by Information Handling ServicesMIL-P-qA077 13 9777906 031b038 T W MIL-P-48077 (MU) 3.8 Submission of results of contractor-conducted exam- inations and tests.-T
15、he contractor shall forward copies of the results of any of his examinations or tests to the desiunated -a address as required by the contract. (See 6.6) 3:iI.B visions for first article testing. Submission of first article quantity by the contractor shall be as specified in the contract. First arti
16、cle testing.-This specification makes pro- 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.-Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specifie
17、d in the con- tract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection re- quirements specified herein, unless disapproved by the Govern- ment. The Government reserves the right to perform any of the inspections set forth in the specificatio
18、n where such inspec- tions are deemed necessary to assure supplies and services conform to prescribed requirements. to MIL-STD-109 to define terms used herein. The provisions of MIL-A-2550 shall apply. Reference shall be made 4.1.1 Submission of product.-At the time the completed lot of items delive
19、rable under the contract is submitted to the Government for acceptance, the contractor shall supply the following information accompanied by a certficate which attests that the information provided is correct and applicable to the product being submitted: a. b. Drawing and specification number and d
20、ate, together c. A statement that the lot complies with all the quality assurance provisions specified in this specification. I with identification and date of changes thereto. A statement that all material purchased by the contrac- tor meets requirements, when such material. is controlled by Goverm
21、ent or commercial specifications referenced;in any of the contractual documents, and that certificates of conformance are on file and available for review, with the exception that a statement of findings on the moisture content of each explosive shall be furnished with each lot submitted for accepta
22、nce. d. Number of items in the lot. e, Date submitted. 4 Licensed by Information Handling ServicesMIL-P-48077 I3 9799906 0336037 I m- MIL-P-48077 (Mu) The certificate shall be signed by a responsible agent of the certifying organization. The initial certificate submitted shall be substantiated by ev
23、idence of the agents authority to bind his principal. authority will not be required with subsequent certificates unless, during the course of the contract, this authority is vested in another agent of the certifying organization. Substantiation of the agents 4.2 First article inspection. 4.2.1 Subm
24、ission.-The contractor shall submit a first article quantity as designated by the Contracting Officer for evaluation in accordance with the provisions of 4.2.2. (See 6.1) The first article sample shall consist of one- hundred and fifty (150) primers. All parts and completed assemblies shall have bee
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILP480771972PRIMERM104PARTSFORANDLOADINGASSEMBLINGANDPACKINGM104 引物 零件 及其 组装 包装 PDF

链接地址:http://www.mydoc123.com/p-446351.html