ARMY MIL-M-13081 F-1987 MIXER ROTARY TILLER SOIL STABILIZATION SELF-PROPELLED《自动式土壤加固旋转式翻土机的搅拌机》.pdf

《ARMY MIL-M-13081 F-1987 MIXER ROTARY TILLER SOIL STABILIZATION SELF-PROPELLED《自动式土壤加固旋转式翻土机的搅拌机》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-M-13081 F-1987 MIXER ROTARY TILLER SOIL STABILIZATION SELF-PROPELLED《自动式土壤加固旋转式翻土机的搅拌机》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、- - -r r a a e-3 5L distribution is unlimited. THIS DOCUMENT CONTAINS PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ - MIL-M-IIOBLF 38 W 9999906 OiILO8b0 9 W c MIL-M-13081F MILITARY MIL-P-514 MIL-T-704 MIL-L-2104 MIL-G-3056 MIL-T-3351 MIL-A

2、-8421 MIL-E-10062 MIL-L-21260 MIL-A-46153 MIL-C-46168 STANDARDS - Plates, Identification, Instruction and marking, Blank. - Treatment and Painting.of Materiel. - Lubricating Oil, Internal Combustion Engine, - Gasoline, Automotive, Combat. - Tractor, Full-Tracked, Low Speed; Tractor Tactical Service.

3、 Wheeled, Industrial: and Their Attachments; Packaging of. - Air Transportability Requirements, General Specifications For. - Engines: Storage. - Lubricating Oil, Internal Combustion Engine, Preservative and Break-In. - Antifreeze, Ethylene Glycol, Inhibited, Heavy Duty, Single Package. - Coating, A

4、liphatic Polyurethane, Chemical Agent Resistant. Preparation for Shipment and FEDERAL FED-STD-H28 e - Screw Thread Standards for Federal Services. MILITARY MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-130 MIL-STD-209 MIL-STD-838 MIL-STD-8 89 MIL-STD-14 74 - Identification Marking of US Mi

5、litary Property - Slinging and Tiedown Provisions for Lifting and Tying Down Military Equipment. - Lubrication of Military Equipment. - Dissimilar Metals. - Noise Limits for Army Materiel. HANDBOOKS I MIL-HDBK-113 - Guide for the Selection of Lubricants, Fluids, Preservatives and Speciality Products

6、 for Use in Ground Equipment Systems. (Copies of specifications, standards, handbooks, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2 Provided by

7、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-13081F 2.2 Other publications. The following document(s) form a part of this sDecification to the extent specified herein. Unless otherwise specified, the icsues of the documents which-are DOD adopted shall b

8、e those listed in the issue of the DoDISS specified in the solicitation. issues of documents not listed in the DoDISS shall be the issue of the Non-Government documents which is current on the date of the solicitation. Unless otherwise specified, the ASSOCIATION OF AMERICAN RAILROADS (AAR) Rules Gov

9、erning the Loading of Department of Defense Materiel on Open Top Cars, section 6. (Application for copies should be addressed to the Association of American Railroads, 50 F Street, Washington, DC 20001.) SOCIETY OF AUTOMOTIVE ENGINEERS SAE Handbook. (Application for copies should be addressed to the

10、 Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.) TIRE AND RIM ASSOCIATION, INC. Yearbook (Application for copies should be addressed to the Tire and Rim Association, Inc., 3200 West Market Street, Akron, OH 44313.) NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGE

11、NT National Motor Freight Classification (Application for copies should be addressed to the American Trucking Associations, Inc., ATTN: Traffic Department, 2200 Mill Road, Alexandria, VA 22314.) AMERICAN NATIONAL STANDARD INSTITUTE/AMERICAN WELDING SOCIETY (ANSI/AWS) D 1.1 Structural Welding Code-St

12、eel (Application for copies should be addressed to the American National Standards Institute, 1430 Broadway, N.Y, N.Y. 10018. UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification Committee, Tariff Publishing

13、Officer, Room 1106, 222 South Riverside Plaza, Chicago, I1 linois 60606. ) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- _- L_ MIL-il-1308LF 38 947790b 0210862 2 . . MIL-M-13081F (Non-Government standards and other publications are normally avai

14、lable from the organizations which prepare or which distribute the documents. documents also may be available in or through libraries or other informational services. ) These 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, t

15、he text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Description. The mixer shall consist of a rotary soil tiller driven by a diesel engine, hydr

16、aulic traction drive, an additive pump and spray bar, a travel speed indicator, flow meter, and necessary controls all mounted on four rubber-tired wheels. structure (ROPS) and falling object protective structure (FOPS). Dimensions and capacities shall conform to table I: The mixer shall be equipped

17、 with a rollover protective TABLE I. Dimensions Cutting width Overall width Overall width Overall length Overall height (Min. 76 inches (193 cm) (Max. operating) 104 inches (264 cm) (Max. sh ipping 96 inches (244 cm) (Max. 25 feet 9 inches (7.85 m) (Max. 102 inches (259 cm) 3.1.1 Performance. The mi

18、xer shall be capable of performing all types of soil stabilization to include bituminous stabilization using asphalt cutbacks and emulsions, cement, lime, and choride. The mixer shall be capable of operating at depths from zero through 10-1/2 inches (266.7 mm) dependent upon soil classification and

19、stablization action required. The mixer cutting and mixing width shall not be less than 76 inches (193 cm). The cut shall be 4 -_I- -_ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-M-L3OBLF 38 7799906 OZLOB63 4 = MIL-M-13081F uniform depth and

20、 the bottom of the cut shall be flat. The mixer shall perform as specified herein without theuse of wheel weights or hydro-inflated tires. The mixer shall operate as specified herein at altitudes up to 5,000 feet (1524 m) above sea-level. The mixer shall be capable of negotiating side slopes of 15 p

21、ercent and longitudinal slopes of 27 percent without any wheel of the mixer losing contact with the ground and without the loss of fuels or lubricants. The tiller shall not be used for tilling under the slope travel requirements. 3.2 First article. Unless otherwise specified (see 6.21, u sample shal

22、l be subjected to first article inspection (see 4.3 and 6.3). deviations of the mixers from the approved first article during production will be subject to the approval of the contracting officer. article willnot relieve the contractor of his obligation to furnish mixers conforming to this specifica

23、tion. Any changes or Approval of the first 3.3 Material. Material shall be as specified herein. Material not specified shall be selected by the contractor and shall be subject to all provisions of this specification. 3.3.1 Material deterioration prevention and control. The mixer shall be fabricated

24、from compatible materials, inherently corrosion resistant or treated to provide protection against the various forms of corrosion and deterioration that may be encountered in any of the applicable operation and storage environment to which the mixer may be exposed. 3.3.2 Dissimilar metals. Dissimila

25、r metals shall not be used in intimate contact with each other unless protected against galvanic corrosion. metals and methods of protection are defined and detailed in MIL-STD-889. Dissimilar 3.3.3 Identification of materials and finishes. The contractor shali identify the specific material, materi

26、al finish or treatment for use with component and subcomponent, and shall make information available upon request to the cmtracting officer or designated representative. 3.3.4 Recovered materials. For the purpose of this requirement, recovered materials are those materials which have been collected

27、from solid waste and reprocessed to become a source of raw materials, as distinguished from virgin raw materials. be newly fabricated from recovered materials to the maximum extent practicable, provided the mixer produced meets all other requirements of this specification. Used, rebuilt or remanufac

28、tured components, pieces and parts shall not be incorpgrated in the mixer. The components, pieces and parts incorporated in the mixer may 3.4 Safety. All rotating or reciprocating parts, and all parts subject to high operational temperature that are of such nature or are so located as to be, or beco

29、me, a hazard to operating or maintenance personnel shall be guarded or insulated to the extent necessary to eliminate the hazard. steps, and ladder rungs shall have antiskid surfaces. directed so as not to endanger personnel or obstruct the view of the operator. All platforms, All exhausts shall be

30、5 .- J _I -. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-13081F Fuel tanks shall be located in a manner which will not allow spills and overflows to run onto the engine, exhaust, or electrical equipment. Electrical equipment shall be insula

31、ted, fully enclosed, or guarded. Nonfunctional sharp edges, projecting points and protruding length more than two full threads of fastening devices shall be avoided. 3.4.1 - (FOPS). Rollover protective (ROPS) and falling object protective structure Unless otherwise specified (see 6.21, the mixer sha

32、ll be equipped with a removable, bolted down ROPS and FOPS canopy. The canopy shall be removable without cutting or welding. The ROPS/FOPS shall conform to SAE 51040 and 5231. A seat belt conforming to 5386 shall be installed for use by the operator. Quick disconnect fittings (electric) shall be pro

33、vided as applicable to facilitate canopy removal. removal of the ROPS/FOPS. A slinging eye(s) shall be provided to facilitate 3.5 Human factors engineering. The mixer shall be operable and maintainable by 5th through 95th percentile dressed appropriate for environments of interest (i.e. arctic, NBC,

34、 etc.) in daylight and darkness in accordance with SAE 5833 and SAE J154a. Instruments shall be designed in accordance with SAE 5898 and SAE 5297. accordance with SAE 5298. Controls and displays shall be provided with universal symbols in 3.6 Noise limits. The noise produced by the mixer shall confo

35、rm with MIL-STD-1474 requirements, with the exception of MIL-STD-1474 5.2, 5.3, and 5.4, when tested in accordance with 4.5.2.14. The provision of MIL-STD-1474, 4.3 and 4.4, shall be provided if and only if MIL-STD-1474, 5.1.1.2 procedures have been pursued and documented to the satisfaction of the

36、procuring activity and written permission to exceed the 85 dB(A) limit is obtained from the procuring activity. Hazard signs shall conform with MIL-STD-1474, 4.3, except the sign will state “HEARING PROTECTION REQUIRED WITHIN (specify) FEET.“ The sign shall be readable at the distance indicated on t

37、he sign. Noise levels shall not exceed the requirements of the EPA nor OSHA for like equipment. 3.7 Maintenance. 3.7.1 Maintainability. All major assemblies and installed attachments shall be accessible for maintenance, repair, and replacement with minimum removal of other major assemblies and insta

38、lled attachments. be removed for component adjustment, or maintenance shall be equipped with quick-disconnect fastenings. drain onto any component or part. incorporate features insuring operating clearances for handtools and lubricating equipment, and the accessibility for service operations such as

39、 adding oil to the engine crankcase and adding oil to gear cases. Access for maintainability shall be in accordance with SAE 5925. Each maintenance, assembly, or disassembly operation required during testing shall be accomplished by no more than two people (except a hoist and operator may be used as

40、 necessary) using special tools furnished with the mixer and common tools. any maintenance operation, the mixer shall operate as specified herein. Covers or plates which must Drain outlets shall be accessible and shall not Ease of maintenance provisions shall After completion of 6 Provided by IHSNot

41、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-13081F 3.7.2 Interchangeability. All parts having the same part number shall be functionally and dimensionally interchangeable. Common hardware and fastening devices such as bolts, nuts, screws, and washers shall b

42、e held to a minimum number of types and sizes. All screw threads shall be in accordance with FED-STD-H28. 3.8 Chassis. All components of the mixer shall be mounted on a chassis of welded-steel construction. The chassis shall have four pneumatic-tired wheels and shall be provided with power-assist, a

43、utomotive steering or articulated steering. Hydraulic or air-actuated brakes shall be provided on the drive wheels. The brakes shall bring the mixer to a full stop from 12 mph in not more than 25 feet. A method for attaching towing chains or cables to the front of the chassis shall be provided. In t

44、he event of power assist failure, the brakes shall be operable with a force not to exceed 70 pounds (32 Kg) and the steering shall be operable with not more than 35 pounds (16 Kg). 3.9 Engine. The manufacturer shall provide a diesel engine of the same type, The engine shall be equipped with dry size

45、, and horsepower that is standard to the commercial product now being offered in the manufacturers literature. type air cleaner. The fuel tank shall have a minimum capacity of 50 gallons (189.27 litre). Oil filters shall be full-flow design. The manufacturer shall supply the following gages : (1) En

46、gine tachometer(s). (2) Water temperature. (3) Ammeter(s) or voltmeter(s). (4) Fuel gage(s). (5) Engine oil pressure gage(s). The engine gages shall be visible and the engine controls shall be accessible from the operators station (platform) in accordance with provisions of 3.5. The engine shall be

47、provided with a dipstick for measuring oil level which is marked per SAE J614b and is in an easily accessible location. The engine in the item application shall be capable of operating continuously at rated load in an ambient temperature of 120 OF (48.9 OC). Heat rejection calculations shall be furn

48、ished and will be acceptable in lieu of testing. shall not exceed the following established limits for an ambient temperature of 120 OF: Calculated temperatures (i) Radiator top tank temperature - 210 OF. (79.38 OC) (2) Engine oil gallery temperature - 230 OF. (86.94 OC (3) Engine oil sump temperatu

49、re - 250 OF. (94.50 OC) 3.10 Electrical system. Unless otherwise specified (see 6.21, the manufacturer shall supply a 24 volt electrical system. Wires, cables, and conductors shall be color-coded or numbered to indicate the connectors with which they mate. Long wires, cables, or bundles of cables shall be secured to the equipment chassis. 3.10.1 Lights. Unless otherwise specified (see 6.2), the mixer shall be equipped with four 24 volt flood lights