ARMY MIL-I-14653-1986 INSIGNIA EMBROIDERED FLAG COMPONENTS GENERAL SPECIFICATION FOR《绣花旗帜组成部分的一般规范》.pdf

《ARMY MIL-I-14653-1986 INSIGNIA EMBROIDERED FLAG COMPONENTS GENERAL SPECIFICATION FOR《绣花旗帜组成部分的一般规范》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-I-14653-1986 INSIGNIA EMBROIDERED FLAG COMPONENTS GENERAL SPECIFICATION FOR《绣花旗帜组成部分的一般规范》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、t DISTRIBUTION STATEMENT A. Approved for public release; distribution is unji L, MIL-1-14653 29 August 1986 SUPERSEDING MIL-1-3037G (IN PART) 30 September 1981 MILITARY SPECIFICATION INSIGNIA, EMBROIDERED FLAG WPONENTS, GENERAL SPECIFICATION FOR This specification is approved for use by all Departme

2、nts and Agencies of the Department of Defense. - R 1. SCOPE 1.1 Scope. This specification covers the Schiffli machine embroidered flag 1.2 Classification. The embroidered flag components covered by this blank cmponents for some military flags. specification shall be of the following types, styles an

3、d classes. Type I - Enbroidered components for Army organizational flag blank. Style 1 - Eagles Wing, Right Style 2 - Eagles Wing, Left Style 3 - Eagles Head, Right Style 4 - Eagles Head, Left Style 5 - Eagles Tail Feathers Style 6 - Eagles Claws and Arrows, Right Class 1 - Yellow HH, Cable No. 6710

4、8 Class 2 - Scarlet HL, Cable No. 67111 Class 3 - Flag Blue HY, Cable No. 67124 Class 4 - Green HAD, Cable No. 67129 Class 5 - Crimson HM, Cable No. 67112 Class 6 - Buff HAK, Cable No. 67135 Class 7 - Orange HK, Cable No. 67110 Class 8 - Brick Red HN, Cable No. 67113 Class 9 - Teal Blue HV, Cable No

5、. 67121 y Class 10 - Oriental Blue HBW, Cable No. 67172 Class 11 - Ultramarine Blue HS, Cable No. 67118 Class 12 - Bottle Green KQ, Cable No. 67191 Class 13 - Maroon HO, Cable No. 67114 Beneficial comnents (recomnendations, additions, deletions) and any pertinent data which may be used in improving

6、this document should be addressed to: Director, The Institute of Heraldry, US Army, Cameron Station, Alexandria, VA 22304-5050, by using the self-addressed Standardization Document Improvenent Proposal (DD Form 1426) appearing at the end of this document or by letter. Licensed by Information Handlin

7、g ServicesMIL-I-L4653 84 7777706 0377284 T MIL-1-14653 Style 7 - Eagles Claws and Arrows, Left Class 1 - Yellow HH, Cable No. 67108 Class 2 - Scarlet HL, Cable No. 67111 Class 3 - Flag Blue HY, Cable No. 67124 Class 4 - Green HAD, Cable No. 67129 Class 5 - Crimson H, Cable No. 67112 Class 6 - Buff H

8、AK, Cable No. 67135 Class 7 - Orange HK, Cable No. 67110 Class 8 - Brick Red HN, Cable No. 67113 Class 9 - Teal Blue HV, Cable No. 67121 Class 10 - Oriental Blue HBW, Cable No. 67172 Class 11 - Ultramarine Blue HS, Cable No. 67118 Class 12 - Bottle Green HCQ, Cable No. 67191 Class 13 - Maroon Ho, Ca

9、ble No. 67114 Style 8 - Eagles Claws and Olive Branch, Right Class 1 - Yellow HH, Cable No. 67108 Class 2 - Scarlet HL, Cable No. 67111 Class 3 - Flag Blue HY, Cable No. 67124 Class 4 - Green HAD, Cable No. 67129 Class 5 - Crimson EM, Cable No. 67112 Class 6 - Buff HAK, Cable No. 67135 Class 7 - Ora

10、nge HK, Cable No. 67110 Class 8 - Brick Red HN, Cable No. 67113 Class 9 - Teal Blue HV, Cable No. 67121 Class 10 - Oriental Blue HBW, Cable No. 67172 Class 11 - Ultramarine Blue HS, Cable No. 67118 Class 12 - Bottle Green HCQ, Cable No. 67191 Class 13 - Maroon Ho, Cable No. 67114 Style 9 - Eagles Cl

11、aws and Olive Branch, Left Class 1 - Yellow HH, Cable No. 67108 Class 2 - Scarlet HL, Cable No. 67111 Class 3 - Flag Blue HY, Cable No. 67124 Class 4 - Green HAD, Cable No. 67129 Class 5 - Crimson HM, Cable No. 67112 Class 6 - Buff HAK, Cable No. 67135 Class 7 - Orange HK, Cable No. 67110 Class 8 -

12、Brick Red HN, Cable No. 67113 Class 9 - Teal Blue HV, Cable No. 67121 Class 10 - Oriental Blue HBW, Cable No. 67172 Class 11 - Ultramarine Blue HS, Cable No. 67118 Class 12 - Bottle Green HCQ, Cable No. 67191 Class 13 - Maroon HO, Cable No. 67114 2 Licensed by Information Handling ServicesMIL-1-1465

13、3 Type II - Embroidered Cmponents for Air Force Organizational/Provisional Flags, 30“ x 40 in size. Style 1 - Eagle and Clouds, Right Style 2 - Eagle and Clouds, Left Style 3 - USAF Scroll Type III - Embroidered Components for Air Force Ceremonial/Positional flags 44“ x 56 in size. Style 1 - Eagle a

14、nd Cloud, Right Class 1 - Ultramarine Blue Base Cloth Class 2 - White Base Cloth Style 2 - Eagle and Cloud, Left Class 1 - Ultramarine Blue Base Cloth Class 2 - White Base Cloth Style 3 - USAF Scroll Style 4 - Thunderbolt, Wings and Lightning Darts Type IV - Embroidered Canponents for Marine Corps S

15、tandard Flags Style 1 - Eagles Wing, Left Style 2 - Eagles Wirq, Right Style 3 - Eagles Head, Body and Talons, Left Style 4 - Eagles Head, Body and Talons, Right Style 5 - Globe, Land masses, Grid lines and Eagles tail feathers. Style 6 - Anchor, Top, Left Style 7 - Anchor, Top, Right Style 8 - Anch

16、or, Bottan, Left Style 9 - Anchor, Bottom, Right Style 10 - Scroll, Top Style 11 - Scroll, bottom with “United States Marine Corps“. Style 12 - Scroll, bottan with “United States Marine Corps Reserve“. 2, APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, and standards. The followi

17、ng specifications and standards form a part of this specification to the extent specified herein. Ikiless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (D0I)ISS) and supplgnent thereto, cited i

18、n the solicitation. 3 Licensed by Information Handling ServicesMIL-I-LLib53 8Li W 7977706 0377286 3 M MIL-1.14653 SPECIFICATIONS FEDERAL 3X-C-476 - Cloth, Bunting, Nylon; and nylon and wool. PPP-B-636 - Boxes, Shipping, Fiberboard. MILITARY MIL-C-606 - Cloth, Banner, Rayon. STANDRDS FEDERAL FED-STD-

19、191 - Textile, Test methods. FED-STD-751 - Stitches, Sem and Stitchings. MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for; Shipment and Storage. MIL-STD-147 - Palietized Unit Loads. MIL-STD-794 - Parts and Equipment, Procedures for Packaging of. Attri

20、butes . 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. issues shall be those in effect on the date of the solicitation. Unless otherwise specified, th

21、e DRAWINGS THE INSTITUTE OF HERALDRY 5-6-1 Base Drawing for Details of Eagle, Olive Branch and 5-6-U3 Base Drawing, Master Layout for Cartoons (Army) 5-6-2 Base Drawing for Organizational Colors with Color 5-100-1 Air Force Organizational Flags 5-101-1 Coat of Arms, United States Air Force 5-101-lA

22、Ceremonial Flag, United States Air Force 5-100-1, Sheet 2 - Base Drawing, USAF, Organizational Flags, 5-101-lA, Sheet 2 - Ceremonial Flag, USAF, Components on Base Arrows (Army) Specifications (Army) Cmponents on Base Cloth Cloth 4 Licensed by Information Handling ServicesMIL-I-lLIb53 8LI 779770b 03

23、77287 5 O 1 i I i L 1 L i I L L i MIL-1-14653 5442-1, Sheet 1 - Organizational Flag for UsMc 5-MC-1, Sheet 2 - Device for Organizational Flag, UsMc 5442-1, Sheet 3 - Scroll for Organizational Flag, USE. 5-MC-1, Sheet 4 - Base Cloth for Components, Organizational Flag 5-MC-1, Sheet 5 - Base Cloth for

24、 Ehbroidered Scrolls, for USMC Organizational Flags for USE I (Copies of specifications, standards, an other Cbvernments documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer 1 .

25、2.2 Other publications. The following document forms a part of this specification to the extent specified herein. Unless otherwise srxcified. the issues of the documents which-are DOD. adoptp or filling direction eneral Broken, Scuffed, or cut yarns on face Spot, stain, stiffener, or foreign matter

26、on face. . Two or more thread ends untrimned More than two stmps longer than 1/16 inch. . Creased or folded, will not flatten by manual pressure Ehibroidery yarn not an acceptable match to other canponents. Borders Not uniform in width or unevenly trinmed. Free material between edge design and raw e

27、dge of material not as specified. . Not cut in single units when required (base cloth) -1 -2- 3- -*, -*- 3- 3- -*- 3- -2 - -2- -2- ,*- -*- -1 -1 1 - 3- -2- 3- 3- “Defects designated by an (*) asterisk shall be classed as follows: 3 point defect when seriously affecting appearance or serviceability.

28、2 point defect when affecting appearance but not seriously. 1 point defect when affecting serviceability but not seriously. 13 Licensed by Information Handling ServicesMIL-I-Lib53 Bi 999990b O379296 6 = MIL-1-14653 4.6.3 Examination for dimensions. Measurements shall be taken of all points, lines, a

29、reas, curves and spaces for which dimensions are specified in the drawing, including: Border width Device location Device dimension Spaces and distances between intermediate points Width of base cloth extending from canponent The lot size shall be expressed in units of one enbroidered component. scm

30、ple unit shall be one canpletely fabricated canponent. found to be outside of the specified tolerances shall be scored as a defect. The total defects found shall not exceed the maximum of the table in this paragraph. selected for visual examination. specific tolerances provided shall be applied. be

31、performed on all embroidered flag blank canponents. rejected with more than three, 3-point defects or when any of the 3-point defects cannot be repaired. The Each masurement The sample shall be selected at random from among the units The tolerances for paragraph 3.6 or any other A 100 percent inspec

32、tion shall Canponents shall be Lot size Sample size No. of defects (Max) Under 3200 3201to 22,000 over 22,000 5 15 25 0 1 2 4.6.4 Inspection of packaqing. An examination shall be made to determine Defects shall be scored in accordance with The sample unit shall be one shipping container fully prepar

33、ed for that the packaging, packing and marking requirements of section 5 of this specification are complied with. table V. delivery with the exception it need not be sealed. The lot size shall be the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 and

34、the acceptable quality level (AQL) shall be 4.0 defects for per hundred units. TABLE V. Classification of preparation for delivery defects. Examination Defects Markings (exterior and interior) Omitted, incorrect, illegible, of improper cat ion . Ma terials Any canponent missing. size, location, sequ

35、ence or method of appli- Any camponent damaged, affecting service- ability. 14 Licensed by Information Handling ServicesMIL-I-Lqb53 4 W 777770b 0377277 B W r MIL-1-14653 TABLE V. Classification of preparation for delivery defects - continued. a Examination Defects Workmanship c Weight Inadequate app

36、lication of canpnents, such as, incomplete closure of container flaps, improper taping, loose strapping, inadequate stapling . Bulging or distortion of containers. Net weight exceeds requirements. 4.6.4.1 Examination of count. An examination shall be made to determine that the number of insignia per

37、 bundle, box and shipping container is as required by section 5 of this specification. Table VI shall govern this exminaticm. TABLE VI. Examination of count. Examine Unit Packaging a. Number of insignia per bundle Intermedi ate packaging . b. Number of bundles . Packing. C. Number of boxes per shipp

38、ing container Unit of product or lot expressed in units of One bundle One box One shipping container SanPll #Units in lot Up to 300 301 - 500 501 - 800 801 - 1300 1301 incorrect; illegible; of improper size, location, sequence, or method of application 5. PEKAGING 5.1 Preservation. specified (see 6.

39、2). Preservation shall be levels A, C or comercial as 5.1.1 Level A. 5.1.1.1 Unit packaging. Twenty anbroidered flag components of one type, style, class shall be placed flat in a polyethylene bag and taped closed. 5.1.1.2 Intermediate packaging. No intermediate package is required; level C shall ap

40、ply. 5.1.1.3 Level C. Insignia shall be preserved to the MILSTD-794 requirements for this level, 16 Licensed by Information Handling ServicesMIL-I-L4653 4 = 7779706 0377297 I MIL-1-14653 5.1.1.4 Ccsmiercial. Insignia shall be preserved in accordance with ASM-D-3951. 5.2 Packinq. Packing shall be lev

41、el A, B, C or comnercial as specified (see 6.2) . 5.2.1 Level A. Insignia preserved, as specified, shall be packed in a snug- fitting fiberboard shipping container conforming to class weather-resistant, type SF, grade V3s or type CE, grade V3c of PPP-B-636. conformance with the appendix of the appro

42、priate container specification. weight of the contents of each shipping container shall not exceed the size and weight limitation of the container specification. Closure shall be in The 5.2.2 Level B. All insignia, preserved as specified in 5.1, shall be packed in a snug-fitting fiberboard box confo

43、rming to class domestic, grade 200 of PPP-B-636. The weight in each shipping container shall not exceed the weight and size limitation of the container specification. Closure shall be in accordance with the container specification. 5.2.3 Level C. Insignia of one type, style, and class only, preserve

44、d as specified in 5.1, shall be packed to the MIL-Sm-794 requirements for this level . 5.2.4 Conmercial. Insignia, preserved as specified in 5.1, shall be packed in accordance with the applicable requirements of ASTM-D-3951. 5.3 Palletization. Items packed as specified shall be palletized on a 4-way

45、 entry pallet in accordance with load type IA of MIL-S1D-147. load shall be bonded with primary and secondary straps in accordance bonding means C, K and L, O or P. appendix of MILSTD-147. size A, wood group I, II, III or IV of MIL-P-15011 or 4-way, type IV, V or WII, class 1, style A, size 2, wood

46、group I, II, III or IV, grade A of NN-P-71. each course. the patterns specified in MIL-STD-147, the pallet pattern used shall be approved by the contracting officer. Each prepared Pallet pattern shall be in accordance with the The pallet shall be 4-way, type I, class 1, style 1, Interlocking of load

47、s shall be effected by reversing the pattern of If the container is of a size which does not conform to any of 5.4 Marking. In addition to any special marking required by the contract or purchase order, unit packs, shipping containers, and palletized unit loads shall be marked in accordance with MIL

48、STD-129 or ASTM-D-3951, as applicable. 5.4.1 Unit packaging. Unit packaging shall have the required information legibly printed or stmped in black on the bag across the center face, or on a white paper label inserted with in the bag so as to permit ready identifica- tion. The bag or label shall indi

49、cated the following: 17 Licensed by Information Handling Services- NIL-I-l14653 84 W 7777706 0377300 4 MIL-1-14653 Stock Number Nomenclature Quantity 6. NOTES 6.1 Intended use. be used for appliquing on organizational and statutory flags used by the Department of Defense. The insignia covered by this specification are intended to 6.2 Ordering data. 6.2.1 Ordering data. Procurement documents should specify the following: a. Title, number and date of this specificatim. b. Type, style, class required (see 1.2). C. Drawing number (see 2.1.2). d. Wh