ARMY MIL-I-14646-1976 INSIGNIA SHOULDER LOOP COMBAT LEADER IDENTIFICATION《战斗领袖认证肩章》.pdf

《ARMY MIL-I-14646-1976 INSIGNIA SHOULDER LOOP COMBAT LEADER IDENTIFICATION《战斗领袖认证肩章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-I-14646-1976 INSIGNIA SHOULDER LOOP COMBAT LEADER IDENTIFICATION《战斗领袖认证肩章》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-I-14b4b 84 m 977770b 0377106 B _- - MIL-I- 14 64 6 (IH) 30 September 1976 MILITARY SPECIFICATION INSIGNIA, SHOULDER LOOP, COMBAT LEADER EDENTIFICATION Tkin apecitmenk 06 Vede. 1. SCOPE * -1 This specification covers one type of insignia worn on the shoulder - II .-. .-_ - .- -. . -G z ,- loop to

2、 designate combat leader. -. . APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date of invitation for bids or request for propsai, form a part of this specification to the extent specified herein. SPE XFICATIONS i EDERAL C-F-206 - Felt, Sheet, Cloth, Felt, Wool, Pressed P

3、PP-B-566 - Boxes, Folding, Paperboard PPP-B-676 - Boxes, Setup PPP-B-636 - Box, Shipping, Fiberboard MILITARY MIL-F-10884 - Fasteners, Snap STANDARDS FEDERAL FED-STD-191 - Textile Test Methods MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking fo

4、r Shipment and Storage BENEF IC I AL COMMENTS (RECOMMENDAT IONS , ADD IT I ONS , DELET I ONS) AND ANY PERTI NENT DATA WICH HAY BE USED IN IMPROVING THIS DOCUMENT SHOULD BE ADDRESSED TO: DIRECTOR, THE INSTITUTE OF HERALDRY, US ARMY, CAMERON STATION, ALEXANDRIA, VA 22314, BY USING THE SELF-ADDRESSED S

5、TANDARDIZATI OW DOCUMENT IMPROVEMENT PROPOSAL (DD FORM 1426) APPEARING AT THE END OF THIS DOCUMENT QR BY LETTER. - PSC 8455/ +- - - - - -/ _ T#PS BmT CiN3M!tI8 3 d f 1 _.- 7 1B -“- A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-I-14bLIb BLI W

6、 9999906 0379307 T MIL- I- 14 64 6 (IH) DRAWING A-13-49 - Insignia, Shoulder Loop., - Combat Leaders Identification (Copies of specifications, standards and drawings required by the contractor in connection with specific procurement functions should be obtained from the procuring activity or as dire

7、cted by the contracting officer. ) (Figure 1 is a miniature reproduction of the referenced drawing and is attached for information purposes only,) 2.2. Other publications. - The following document forms a part of this Specification to the extent specified herein. Unless otherwise indicated, the issu

8、e in effect on date of invitation for bids or request for proposal shall apply THE COLOR ASSOCIATION OF THE UNITED STATES, INC. Standard Color Card of America, 9th Edition (Application for copies of the color card should be addressed to The Association of the kited States, Inc.; 200 Madison Avenue;

9、New York, NY 10016.) Color 3. EQUIREMENT 3.1 Standard shade sample. - When specified (see 6.2) a standard shade sample shall be furnished for matching color and colorfastness only. 3.2 First article.- When specified (see 6.2), before production is com- menced a sample of the furnished item shall be

10、submitted or made available to the contracting officer or his authorized representative for inspection and tests as specified in 4.2. commencement of production but does not relieve the manufacturer of responsi- bility for compliance with all applicable provisions of this specification. The first ar

11、ticle shall be manufactured in the same manner and by the same facilities to be used for the production items. The approval of the first article authorizes the 3,3 Materials.- Materials shall conform to the referenced specifications and the requirements specified herein. 3.3.1 - Felt.- The felt for

12、the shoulder loop shall conform to type III, class 7A1 of C-F-206. 3.3.1.1 Color and colorfastness.- The felt shall be Hunter Green conforming to Cable Number 70064 and shall show fastness to wet-dry cleaning, crocking and light equal to or better than the standard shade sample. no standard is avail

13、able the felt shall show good fastness to wet-dry cleaning, crocking and light for forty hours. When 3.3.2 Snap fasteners.- Snap fasteners shall conform to style 3, 17 ligne, finish 2 of FEL-F-10884. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI

14、L-I-L4646 q 7977706 O377LO8 L r_ - MIL-T-14646 (IH) - 3.4 Construction.- Shoulder loops shall be constructed in accordance with the details and dimension on drawing A-13-49. 90 degree angies and sides shall be straight. in 3.3.2, shall be located as shown and securely clinched without cutting the ma

15、terial. All. corners shall be Snap fasteners specified 3.5 Workmanship.- Shoulder loops shall be clean, well niade and shall meet the acceptable quality levels established by this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.- Unless otherwise specified in the .1-

16、 contract or purchase order, the supplier is responsible for the performnee of all inspection requirements as specified herein. specified in the contract or purchase order, the supplier may use his own or any other facilities suitable for the performnee o inspection require- ments specified herein,

17、unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the- specification where such inspections are deemed necessary to assure supplies and services conform to the prescribed requirements. - Except as otherwise . 4. First article inspe

18、ction.- When first articles are required, in- spectio;- and testing of the first article shall be made on a completely fabricatttl insignia for all provisions of this specification applicable to the en, product examination and tests. 4.3 Inspection for acceptance.- Unless otherwise indicated, inspec

19、tion shall be in accordance with MIL-STD-105. 4.3.1 Component testing.- In addition to the quality assurance provisions of the subsidiary specifications and drawings, testing shall be performed on components and materials listed in table I for test charac- teristics shown. quality level (AQL) shall

20、be 6.5 defects per hundred units. be in accordance with FED-STD-191. The inspection levei shall be S-2 and the acceptable Testing shall TABLE I Component testing.- Component Characteristic Rqm t Test Lot size k3arnple unit ref method expressed for testing Felt colorfastness to: Wet-dry cleaning 3.3.

21、1.1 5622 1 yard 1 yard long Crocking 5651 1 5/8“ wide . Light l/ . 5660 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-14646 (IH) - i/ as a result of suspected anomalous behavior of certain dye types or formulations, the contracting officer

22、may authorize the exposure to natural light in accordance with Method 5662. In the event o a dispute resulting from the test with Method 5660, or 4.3.2 Inspection of end item.- 4.3.2.1 Visual examination.- Defects found during the examination shall be scored in accordance with the listing below, be

23、expressed in terms of one insignia. accordance with ihspection level II and the AQL shall be 4.0 defects per hundred units. The lot size shall The sample size shall be in Examine Defect Quality of cloth Color Color other than specified. Off shade. Material snap fastener Hole, cut, tear, smash or wea

24、k place. Spot, stains, streaks or shade bars. Open, breaks or thin areas. Abrasion or rub. High, thick or lumpy area. Wrinkle or crease. Objectionable odor. Not clean. Extraneous foreign matter. Male or female portion missing or broken. Male or female portion split. Out of alignment or not in locati

25、on specified. Not type specified. Finish not as specified. Burr or sharp edge. Not securely at tached. Will not function as intended. - Malformed, misshapen, damaged or otherwise impaired. 4.3.2.2 Examination for defects in dimensions.- Any dimension that is not within the specified tolerance shall

26、be classified a defect. size shall be expressed in units of one insignia. be one insignia. AQL shall be 4.0 defects per hundred units. The lot The sample size shall be in accordance with 5-3 and the The end product shall 4.3.2.3 Examination for count.- The following shall govern this examination : P

27、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-14646 4 = 7979906 0379111 I MIL-l4646(IB) . .%. Lot expressed Sample Size Examina tion in units of Unit of product No. of units No. of units a. #insignia ke folding or One folding or Up to 300 -4 p

28、er folding or Set-up box se t-up box 301 or aver 5 Set-up box b. #folding One shipping One shipping up to 3 All dr Set-up container container 4 to 6 3 boxes per 7 and over 4 shipping container & -. . =- The lot shall be unacceptable if any of the following are found: (a) Number of insignia per foldi

29、ng or Set-up box. (1) The average number of insignia per box in sample is less -. - than specified or the qmntity mrked on the box. (2) The number of insignia in any box is more than 5-percent under the quant+y specified or the quantity marked on the box. (b) sfgnia per c. ntainer is less than speci

30、fied or less than quantity marked on container. NuIsier of insignia per shipping container - actual number o in- 4,3.3 Emmination of preparation for delivery requirements.- An exam- ination shall be made to determine that packaging, packing and marking re-. quirements of section 5 of this specificat

31、ion are compiled with. shall be scored in accordance with defects list below. be one shipping container fully packed, selected just prior to the closing operation. containers fully prepared for delivery. of containers in the inspection lot, the AQL shall be 4.0 defects per hundred units. Defects Sam

32、ple unit shall Defects of closure listed below shall be examined on shipping The lot size shall be the number The inspection level shall be S-2 and - 1. - - Examine Defect - _ Marking (exterior Omitted, incorrect, illegible, of improper size, and interior) location, sequence or method o application.

33、 &terial Any component missing, Any component damged, affecting serviceability. 6adequate application of components, such as, incomplete closure of case liners, container flaps,. zi Workmanship / loose strapping, inadequate stapling. Bulging or distortion of containers.- 5 Provided by IHSNot for Res

34、aleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-L464b - 4 9999906 0379330 T W MIL-1-14646 (IH) 5. PREPARATION FOR DELIVERY 5.1 Packaging.- Packaging shall be level A or C, as specified (see 6.2). insgnia shall be packaged in a setup, paperboard box conforming to variety

35、 1, style III or IV type B, class A of PPP-B-676 or a folding paperbox conforming to variety 1, style III, type B, class A of PPP-B-566. shall be in accordance with the appendix of the applicable box specification. 5.1.1 Level A.- One hundred twenty five pair of Bhoulder loop Closure 5.1.2 Level C.-

36、 Shoulder loop insignia shall be packaged to afford protection against deterioration and damage during shipment from the supply source to the first receiving activity. 5.2 Packing.- Packing shall be level A, B or C, as specified (see 6.2). 5.2.1 Level A.- Five thousand pair (40 intermediate boxes) o

37、f shoulder loop insignia packaged as specified in 5.1 shall be packed in a snug-fitting fiberboard shipping container confoming to Class Weather Resistant, V3s or V3c of PPP-B-636. Closure shall be in accordance with the appendix of the container specification. The weight of the contents of each shi

38、pping container shall not exceed the size and weight limitations of the container specification. 5.2.2 Level B.- Five thousand pair (40 intermediate boxes) of shoulder loop insignia packaged as specified in 5.1 shall be packed in snug-fitting fiberboard box conforming to class Domestic, grade 275 of

39、 PPP-B-636. Closure shall be in accordance with the appendix of the container specification. The weight of the contents of each shipping container shall not exceed the size and weight limitations of the container specification. 5.2.3 Level C.- Shoulder loop insignia shall be packed in containers whi

40、ch are acceptable by common or other carriers for safe transportation to point of destination specified in shipping instructions at the lowest trans- portation rate for such supplies. - - 5.3 Marking.- In addition to any special marking required by the contract or order, interior packages and exteri

41、or shipping containers shall be marked in accordance with MIL-STD-129, except the interior packages shall be marked with the contractors name and the contract or order number. 6. NOTES 6.1 Intended use.- Shoulder loop insignia covered by this specification are intended to be worn by Army personnel t

42、o indicate the wearer is designated a combat leader. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-34646 84 W 9799906 0379332 3 = T MZL-1-14646 (IH) 6 .-2 Ordering data. - Procurement documents should specify the following : (a) (b) Title,

43、number and date of this purchase description. When a standard shade sample will be furnished (see 3.1). (c) When a first article is required- (see 3.2). (d) 5.1 and 5.2). - - Selection of applicable levels of packaging arid packing (see 6.3 The naphthalene flakes requirement is not applicable when G

44、overnment furnished wool or part wao1 fabric has been moth pzoof treated. 6.4 Supersession data.- This specification includes the requirements of the Institute of Heraldry Purchase Description IH-1-73. c- - /- - ,/ v- Custodian: Arm= IH- - _- Review Activity : DLA-GT Preparing Activity : The Institu

45、te of Heraldry. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T P- / 3 I i ,/- MIL-1-14646 Bq m 9999906 0379113 5 m MIL-1-14646 (IH- - .-._ FIGURE 1 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-