ARMY MIL-DTL-62337 C-2011 AIR CLEANER ASSEMBLY.pdf

《ARMY MIL-DTL-62337 C-2011 AIR CLEANER ASSEMBLY.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-62337 C-2011 AIR CLEANER ASSEMBLY.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、Comments, suggestions, or questions on this document should be addressed to U.S. Army RDECOM, Tank Automotive Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS #268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed to DAMI_STANDARDIZATIONconus.army.mil. Since contact in

2、formation can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 2940 NOT MEASUREMENT SENSITIVE MIL-DTL-62337C(AT) 10 February 2011 SUPERSEDING MIL-DTL-62337B(AT) 29 April 1999 DETAIL SPECIFICATION AIR

3、CLEANER ASSEMBLY This specification is approved for use by the U.S. Army Tank Automotive Research, Development and Engineering Center (TARDEC), Research, Development and Engineering Command (RDECOM), Department of the Army, and is available for use by all Departments and Agencies of the Department o

4、f Defense. 1. SCOPE 1.1 Scope. This specification covers a 900 cubic foot per minute (ft3/min) 425 liter per second (L/s), fender-mounted, heavy-duty, two-stage, dry-type air cleaner assembly referred to herein as the “assembly” (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in

5、 this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document us

6、ers are cautioned that they must meet all specified requirement documents cited in sections 3 and 4 of this specification, whether or not they are listed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-62337C(AT) 2 2.2 Government documents.

7、2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). FEDERAL STANDARDS F

8、ED-STD-595/24084 - Green, Semigloss. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-62309 - Filter Element, Air. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-810 - Environmental Engineering Considerations and Laboratory Tests (Copies of these documents are available from https:/assist.daps.dla.mil/quicksea

9、rch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified

10、 herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). U.S. ARMY DRAWINGS 11669740 - Air Filter Element. 12325888 - Air Cleaner Assembly - Armored (Clean Air). (Copies of these drawings are available from DAMI_STANDARDIZATIONconu

11、s.army.mil or U.S. Army RDECOM, Tank Automotive Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS #268, 6501 E. 11 Mile Road, Warren, MI 48397-5000.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless o

12、therwise specified, the issues of these documents those cited in the solicitation or contract (see 6.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-62337C(AT) 3 ASTM INTERNATIONAL ASTM C800 - Glass Fiber Blanket Insulation (Aircraft Type

13、) (DoD Adopted). (Copies are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or website: http:/www.astm.org.) SAE INTERNATIONAL SAE AS478 - Identification Marking Methods (DoD Adopted). (Copies of this document are available from

14、 www.sae.org or SAE Customer Service, 400 Commonwealth Drive, Warrendale, PA 15096-0001.) INTERNATIONAL ORGANIZATION FOR STANDARDIZATIO (ISO) ISO 5011 - Inlet Air Cleaning Equipment for Internal Combustion Engines and Compressors Performance Testing (Copies of these documents are available from www.

15、iso.org or American National Standards Institute, 11 West 42nd Street, New York, N.Y. 10036.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersed

16、es applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.5. 3.2 Material. Materials shall be uniform and free from imperfections or defec

17、ts which affect their serviceability (see 4.8.1). 3.2.1 Corrosion protection. All metallic parts shall be made from corrosion resistant steels or treated/ plated with corrosion-resistant materials (see 3.7.2 and 4.8.1). 3.2.2. Asbestos and cadmium usage. Asbestos and cadmium materials shall not be u

18、sed in any form in any part of the assembly (see 4.8.1). 3.2.3 Radioactive material usage. No item, part or assembly shall contain radioactive materials in which the specific activity is greater than 0.002 microcurie per gram or activity per item equals or exceeds 0.01 microcuries (see 4.8.1). Provi

19、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-62337C(AT) 4 3.2.4 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided th

20、at the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs (see 4.8.1). 3.3 Design and construction. The assembly shall be constructed as specified herein and in accordance with Drawing 12325888. The assembly shall incorpora

21、te a precleaner, filter element and a vehicle exhaust dust ejection system (VEDES) precleaner scavenging manifold (see 4.8.1 and 6.2). 3.3.1 Filter element. The filter element shall be in accordance with MIL-PRF-62309 and Drawing 11669740 (see 4.8.1). 3.3.2 Weight. The weight of the assembly shall n

22、ot exceed 600 pounds (lb) (272 kilogram (kg) (see 4.8.1). 3.4 Operating requirements. Except as otherwise specified herein, requirements shall be met under the following standard conditions: a. Temperature: 73 + 18 degrees Fahrenheit (F) (23 + 10 degrees Celsius (C). b. Humidity: 50 + 15 percent (%)

23、. c. Density of air: 0.073 pounds per cubic foot (lb/ft3) 1.17 kilogram per cubic meter (kg/m3) at 80F (27C). d. Pressure: 30 + 1 in. of mercury (Hg) (101 + 3 kilopascals (kPa). e. Dust: Chemical analysis of dust and particle size distribution shall be in accordance with ISO 5011. f. Air flow: 900 f

24、t3/min (425 L/s). g. Dust feed rate: 0.025 + 0.005 gram per cubic foot (g/ft3) (0.88 + 0.18 g/m3) of actual input airflow. Actual input airflow shall be defined as airflow plus the scavenge airflow for each of the five 10 minute stepped airflow cycles listed in table I. (NOTE: First step would have

25、an actual input airflow of 970 ft3/min.) 3.4.1 Initial airflow restriction. The initial airflow restriction of the assembly shall not exceed 9 in. of water (2.24 kPa) (see 4.8.2.1) 3.4.2 Dust capacity. When operating with a stepped airflow in accordance with table I and fed with ISO 5011 coarse dust

26、 using the prescribed dust injector as specified in ISO 5011, the time for the assembly to reach load capacity (see 6.6.1) shall be not be less than 80 hours. There shall be no dust tracking on the downstream side of the element. The coarse dust accumulative efficiency shall not be less than 99.9% a

27、nd the precleaner efficiency shall be not be less than 97% (see 4.8.2.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-62337C(AT) 5 TABLE I. Stepped air flow. Time Rated flow Air flow Scavenge airflow (minute) (%) ft3/min (L/s) ft3/min (L/

28、s) 10 100 900 (425) 70 (33) 10 60 540 (255) 107 (50) 10 20 180 (85) 128 (60) 10 80 720 (340) 92 (43) 10 60 540 (255) 107 (50) 10 40 360 (170) 120 (57) 3.4.3 Dust efficiency. The assembly shall remove ISO 5011 fine dust from air at an initial efficiency of not less than 99.5% with a period of 30 minu

29、tes using the prescribed dust injector as specified in ISO 5011. If the air cleaner has an air flow velocity rating of 6 ft/min (183 cm/min) or less, the dust shall be fed for 60 minutes (see 4.8.2.3 and 4.8.2.3.1). 3.4.4 Post service airflow restriction. After one operation to load capacity in acco

30、rdance with 3.4.2, the assembly air flow restriction shall not have increased by more than 1 in. of water (0.25 kPa) above that measured in 3.4.1 (see 4.8.2.4). 3.4.5 Air leakage resistance. There shall be no more than 2 in. of water (0.5 kPa) drop in 3 minutes when the assembly is subjected to a va

31、cuum of 30 + 0.5 in. of water (7.5 + 0.1 kPa) (see 4.8.2.5). 3.5 Interface requirements. The assembly shall conform to the interface envelope dimensions and mounting in Drawing 12325888 (see 4.8.3). Each assembly shall accommodate the inputs and interfaces specified in 3.3 through 3.3.2. 3.6 Support

32、 and ownership requirements. Each assembly shall possess the following life cycle ownership characteristics. 3.6.1 Identification marking. Identification marking shall be permanent and in accordance with SAE AS478, and shall include the maximum rated air flow, part number, month, and year of manufac

33、ture (see 4.8.4.1). 3.6.2 Painting. Unless otherwise specified (see 6.2), the preparation, conditioning, and painting of the assembly shall be in accordance with the manufacturers standard practices. Exterior color shall be in accordance with color chip 24084 (Green, Semigloss) of FED-STD-595 (see 4

34、.8.4.2). 3.6.3 Serviceability. Servicing, cleaning, and reassembly shall be accomplished without the use of special tools and without disturbing the air cleaner connections to the engine (see 4.8.4.3). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

35、MIL-DTL-62337C(AT) 6 3.6.4 Interchangeability. The assembly shall be designed and fabricated such that 2 or more items possessing functional and physical characteristics which are equivalent in performance and durability are capable of being exchanged one for the other without alteration of the item

36、s themselves or of adjoining items except for adjustment, and without selection for fit, repair parts, or performance (see 4.8.4.4). 3.6.5 Safety. The assembly shall be cleaned of any foreign material which might detract from the intended operation, function, or appearance of the assembly. Screws, n

37、uts, and bolts shall show no evidence of cross threadings, mutilation, or detrimental or hazardous burrs, and shall be firmly secured. Bearing assemblies shall be free of rust, discoloration, and imperfections of ground, honed, or lapped surfaces. Contacting surfaces shall be free of tool marks, gou

38、ge marks, nicks or other surface-type defects. There shall be no detrimental interference, binding, or galling (see 4.8.4.5). 3.7 Operating environment requirements. 3.7.1 Vibration. The assembly shall be capable of withstanding the vibration profile of figure 1 for a period of 80 minutes (including

39、 forced dwells of 13.33 minutes each) in each of the three mutually perpendicular axes (see 4.8.5.1). 3.7.2 Salt fog. The assembly shall withstand exposure to salt fog atmosphere. The salt fog atmosphere shall consist of a salt fog solution defined as 5% by weight NaCl and 95 % by weight distilled w

40、ater. The exposure zone temperature range shall be 90 to 95F. The fog density shall be approximately 3 quarts of solution to each 10 cubic feet (see 4.8.5.2). 4. VERIFICATION 4.1 Inspection equipment. Unless otherwise specified in the contract (see 6.2), the contractor is responsible for the provisi

41、on, maintenance, and accuracy of all inspection equipment necessary to assure that supplies and services conform to contract requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-62337C(AT) 7 Axis Sweep acceleration 5 to 500 to 5 Hz a

42、t 0.9 octaves/minute Forced dwells 1st 2nd 3rd gravity (G) Accel. (G-level) Freq. (Hz) Accel. (G-level) Freq. (Hz) Accel. (G-level) Freq. (Hz) Vertical (Z) 0.9 4.2 20 2.4 105 2.4 265 Transverse (Y) 0.9 1.5 50 1.8 100 - - Longitudinal (X) 0.9 1.2 245 - - - - FIGURE 1. Vibration levels for assembly. 4

43、.2 Classification of inspection. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.5). 1. Preproduction inspection (see 4.5.1). 2. Initial production inspection (see 4.5.2). b. Conformance inspections (CI) (see 4.6). 1. Examination (see 4.6.2)

44、. 2. Tests (see 4.6.3). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-62337C(AT) 8 4.3 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be conducted in accordance with 4.4 and under the following conditions

45、: a. Temperature: 73 + 18F (23 + 10C). b. Humidity: 50 + 15%. c. Density of air: 0.073 lb/ft3 (1.17 kg/m3 ) at 80F (27C). d. Pressure: 30 + 1 in. of Hg (101 + 3 kPa). 4.4 Inspection procedures. Unless otherwise specified (see 6.2), all test procedures shall be in accordance with 4.3 and the followin

46、g: a. The test setup for all tests requiring airflow shall be as shown in figure 2. b. Dust feed rates shall be averaged over 10-minute intervals. c. Measured airflow restriction values shall be corrected to the specified air density (see 3.4c) to an accuracy of 0.1 in. of water (25 Pa). d. Actual a

47、irflow values used in tests shall be corrected to standard conditions (see 3.4c) and shall be within + 2% of specified values. e. The assembly shall be mounted in its normal operating attitude as shown in figure 2 and shall be electrically grounded. f. In all tests, the assembly shall be connected t

48、o a turbine vacuum source as shown in figure 2. The vacuum source shall provide a scavenge airflow as specified in 3.4.2. g. For first article testing, two filter elements shall be used for each assembly tested. The second filter shall be inserted subsequent to the post service airflow restriction t

49、est prior to the dust efficiency test. h. Air shall be drawn through the assembly with a turbine vacuum source to insure filter element dryness before starting tests. 4.5 First article inspection. First article inspections shall be performed on preproduction or initial production samples as specified in the contract or order. 4.5.1 Preproduction inspection. Unless