ARMY MIL-DTL-3943 346 A-2012 DECORATION STATE AND LOCAL LAW ENFORCEMENT CONGRESSIONAL BADGE OF BRAVERY U S DEPARTMENT OF JUSTICE.pdf

《ARMY MIL-DTL-3943 346 A-2012 DECORATION STATE AND LOCAL LAW ENFORCEMENT CONGRESSIONAL BADGE OF BRAVERY U S DEPARTMENT OF JUSTICE.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3943 346 A-2012 DECORATION STATE AND LOCAL LAW ENFORCEMENT CONGRESSIONAL BADGE OF BRAVERY U S DEPARTMENT OF JUSTICE.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A Page 1 of 4 FSC 8455 INCH - POUND MIL-DTL-3943/346A 2 November 2012 SUPERSEDING MIL-DTL-3943/346 8 May 2012 DETAIL SPECIFICATION SHEET DECORATION, STATE AND LOCAL LAW ENFORCEMENT, CONGRESSIONAL BADGE OF BRAVERY, U.S. DEPARTMENT OF JUSTICE This specification is approved for use by all Depar

2、tments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3943. OBVERSE REVERSE MATERIAL: Red Brass 85/15 (UNS Alloy No. C-230) Provided by IHSNot for ResaleNo reproduction o

3、r networking permitted without license from IHS-,-,-MIL-DTL-3943/346A Page 2 of 4 DIMENSIONS: HEIGHT: 2-5/8 inches (REF) WIDTH: 1-7/8 inches (REF) THICKNESS (across center of shield): 0.175 inch 0.010 inch PIERCINGS: Piercings shall be as indicated above. FINISH: OBVERSE: NICKEL: Borders of pendant

4、cross and star band, stars within star band, Capitol Dome and wreath shall be Nickel Plated, Matte Finish, Polished Highlights, and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 18. GOLD: Central badge and all elements of the Congressional Seal on it shall be 24K Gold Plated,

5、 Matte Finish, Polished Highlights, and shall match TIOH Metal Finish Chip Number 8. EPOXY: Epoxy enamel shall be applied as indicated below, and shall match TIOH Hard Enamel Color Chip Numbers listed: TIOH HARD ENAMEL COLOR CHIP NUMBER LOCATION Blue #20 Star Band White #28 Arms of Cross REVERSE: NI

6、CKEL: Borders of pendant cross, designation band and lettering within designation band, back of Capitol Dome, and wreath shall be Nickel Plated, Matte Finish, Polished Highlights, and shall match TIOH Metal Finish Chip Number 18. GOLD: Central badge and lettering on it shall be 24K Gold Plated, Matt

7、e Finish, Polished Highlights, and shall match TIOH Metal Finish Chip Number 8. The nameplate portion of the badges surface shall be made suitable for engraving. EPOXY: Hard epoxy enamel shall be applied as indicated below, and shall match TIOH Hard Enamel Color Chip Number listed: TIOH HARD ENAMEL

8、COLOR CHIP NUMBER LOCATION White #28 Arms of Cross Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3943/346A Page 3 of 4 ATTACHING DEVICE: The suspension ring through which the neckband passes shall be made of Red Brass 85/15 (UNS Alloy C-230

9、), conform to the dimensions specified below, The pendant ring shall be hard soldered to the reverse of the pendant as shown and in such a way that it is not visible when viewing the pendants obverse. NECKBAND: The neckband shall conform to Figure 9 in the latest version of MIL-DTL-3943, except that

10、 the manufacturer may deviate from this drawing by increasing the finished length of the neckband to 26 inches + 1/2 inch - 0. DECORATION CASE: The decoration set shall consist of a neckband with pendant, a service ribbon with ribbon attachment, and a lapel button all packaged in a decoration case c

11、onforming to MIL-C-14633, Type XV, Style 3, with a Type I Class 1 pad. The following shall be inscribed on the top of the decoration case using three lines: (Line 1) CONGRESSIONAL (Line 2) BADGE OF BRAVERY (Line 3) STATE AND LOCAL. NOTES: 1. The term (REF) refers to the measurements taken from the o

12、bverse Government furnished hub or die. 2. The manufacturer may deviate from MIL-DTL-3943 by using nickel underplating prior to plating with 24K gold. 3. Hard cloisonn enamel may be used in lieu of epoxy. If hard cloisonn enamel is used, the required base material is Gilding Metal 95/5 (UNS Alloy C-

13、210). 4. The specification slash sheet for the ribbon for the neckband and service ribbon is MIL-DTL-11589/639. 5. The specification slash sheet for the ribbon attachment is MIL-DTL-41819/49. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39

14、43/346A Page 4 of 4 6. The specification slash sheet for the lapel button is MIL-DTL-11484/340. 7. This item is not authorized for commercial sale, and may be produced only under Government contract and at the request of the U.S. Department of Justice. CHANGES FROM PREVIOUS ISSUE: The margins of thi

15、s specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requiremen

16、ts of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH Civil agency: (Project No. 8455-2012-161) DOJ - BJA NOTE: The activities listed above were interested in this documen

17、t as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Figure 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-