ARMY MIL-DTL-3628 42 F-2009 BADGE QUALIFICATION MARINE CORPS DIVISION RIFLE COMPETITION《海上陆战队师部步枪射击比赛资质徽章》.pdf

《ARMY MIL-DTL-3628 42 F-2009 BADGE QUALIFICATION MARINE CORPS DIVISION RIFLE COMPETITION《海上陆战队师部步枪射击比赛资质徽章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 42 F-2009 BADGE QUALIFICATION MARINE CORPS DIVISION RIFLE COMPETITION《海上陆战队师部步枪射击比赛资质徽章》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 3 FSC 8455 INCH-POUND MIL-DTL-3628/42F 10 November 2009 SUPERSEDING MIL-DTL-3628/42E 15 November 1996 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, MARINE CORPS, DIVISION RIFLE COMPETITION This specification is approved for use by all Departments and Agencies of the Department

2、of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3628. MATERIALS: PENDANT: Gilding Metal DASH NO. SUSPENSION BAR: -1: Gold -1, -2: Red Brass -2: Silver -3: Gilding Metal -3: Bronze FINISH: PENDANT: -1: H

3、ard Enameled, Gold Plated, Matte Finish, Lightly Polished Highlights and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 8. REVERSE - Gold Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 6. -2: Hard Enameled, Silver Plated, Oxidized, Relieved, Lightly

4、 Polished Highlights and shall match TIOH Metal Finish Chip Number 15. REVERSE - Silver Plated, Mirror-like Polished. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/42F Page 2 of 3 -3: Hard Enameled, Oxidized, Highlights Polished. REVER

5、SE - Mirror-like Polished. SUSPENSION BAR: -1: Gold Plated, Matte Finish, Polished Highlights and shall match TIOH Metal Finish Chip Number 8. REVERSE - Gold Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 6. -2: Silver Plated, Oxidized, Buffed Relieved, Matte Finish, Poli

6、shed Highlights and shall match TIOH Metal Finish Chip Number 15. REVERSE - Silver Plated, Mirror-like Polished. -3: Oxidized, Highlights Polished. REVERSE - Mirror-like Polished. DIMENSIONS: PENDANT: DIAMETER: 1-9/32 inches (REF) THICKNESS (at rim): 0.085 inch + 0.005 inch SUSPENSION BAR: HEIGHT (o

7、verall): 3/8 inch (REF) WIDTH (overall): 1-15/32 inches (REF) THICKNESS (edge): 0.065 inch + 0.005 inch ASSEMBLED HEIGHT (overall): 1-3/4 inches NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. Enameled areas shall be as indicated. The color shal

8、l conform to the TIOH chip numbers listed below or the standard sample. COLOR CHIP NUMBER Black 26 White 28 3. Epoxy resin (stoning epoxy) may be used in lieu of hard enamel at the option of manufacturer. Epoxy resin shall be smooth and flush with the dikes. 4. The connecting links shall be fabricat

9、ed from wire with a nominal diameter of 0.044 inch, shall be oblong shaped and 3/16 inch + 1/64 inch long by 1/8 inch + 1/64 inch wide. The links shall be manufactured with the same material and finish as the pendant and suspension bar. 5. Lugs are integral. 6. The attaching device shall be a prong

10、and flat ball clutch type. Red brass flat ball clutches shall be used for Dash No. -1 and -3. Nickel plated flat ball clutches shall be used for Dash No. -2. The prongs shall be located on the horizontal center line of the suspension bar, equidistant from each end and 1-1/16 inches + 1/32 inch apart

11、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/42F Page 3 of 3 CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as

12、 a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous

13、 issue. Custodian: Preparing activity: Army - IH Army - IH Navy NU (Project No. 8455-2010-010) Review activities: Navy - MC DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-