ARMY MIL-D-45441 D (3)-1994 DETONATOR STAB M61 PARTS FOR AND LOADING ASSEMBLING AND PACKING《针刺雷管的M61零件的装载 组装和包装》.pdf

《ARMY MIL-D-45441 D (3)-1994 DETONATOR STAB M61 PARTS FOR AND LOADING ASSEMBLING AND PACKING《针刺雷管的M61零件的装载 组装和包装》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-D-45441 D (3)-1994 DETONATOR STAB M61 PARTS FOR AND LOADING ASSEMBLING AND PACKING《针刺雷管的M61零件的装载 组装和包装》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-D-45441D (AR) AMENDMENT 3 3 June 1994 SUPERSEDING AMENDMENT 2 O1 April 1992 MILITARY SPECIFICATION DETONATOR STAB, M61, PARTS FOR, AND LOADING, ASSEMBLING AND PACKING This Amendment forms a part of Military Specification MIL-D- 45441D (PA) dated 5 April 1974 and is approved for use by the US Arm

2、y Armament Munitions and Chemical Command and is available for use by all Departments and Agencies of Department of Defense. PAGE 8 4.3.2.3, Major Defect 102: Delete the word “concentricityff and substitute the words “true position“. PAGE 12 4.4.1: Delete in its entirety and substitute the following

3、: “4.4.1 Determination of moisture content of lead azide. A tared dried aluminum dish 2 inches in diameter shall be covered with a sheet of polytetrafluoroethylene 2-1/2 inches square and sufficiently flat to form a tight cover. An accurately weighed portion of approximately 2 grams shall be transfe

4、rred to the moisture dish while both the cover and dish are on the balance pan. The dish and contents shall be transferred to an oven and dried at 95 +/- 5 degrees C for 2 hours. The cover shall be placed in a desiccator during the drying period. After drying, the dish shall be quickly transferred t

5、o the desiccator and allowed to cool to room temperature. The PTFE cover shall be placed on the dish and the assembly weighed. The loss in weiaht shall be calculated to percentage of moisture in (PTFE) the lead azide as follows: AMSC N/A 1 of 3 FSC l375 DISTRIBUTION ST- Approved for public release;

6、distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-45441D (AR) AMENDMENT 3 Percentage of moisture = 100(A - B) A Where: A = weight of specimen before drying B = weight of specimen after drying. 4.4.1.1 Determination of m

7、oisture content of lead azide, alternate method. 4.4.1 with the following exception. The sample shall be dried in a vacuum oven at a temperature of 95 +/- 5 degrees C and a pressure of 80 +/- 10 mm mercury for 45 minutes. 4.4.1.2 Determination of moisture content of primer mixture. Transfer an accur

8、ately weighed portion of approximately 1 gram of the primer mixture to a tared aluminum weighing dish provided with a polytetrafluoroethylene (PTFE) cover while both the dish and cover are on the balance pan. Place the dish and contents with the cover removed, in an oven maintained at 60 +/- 5 degre

9、es C for 2 hours. The cover shall be placed in a desiccator during the drying period. After drying, transfer the dish and contents quickly to a desiccator and cool to room temperature. Replace the PTFE cover and weigh. Calculate the loss in weight of the dish, the cover, and the contents to percent

10、moisture in the sample. mixture, alternate method. The procedure is the same as paragraph 4.4.1.2 with the following exception. shall be dried in a vacuum oven at a temperature of 60 +/- 5 degrees C and a pressure of 80 +/- 10 mm of mercury for 45 minutes. The procedure is the same as paragraph 4.4.

11、1.2.1 Determination of moisture content of primer The sample 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-45441D (AR) AMENDMENT 3 PAGE 16 -x- Add the following paragraph: “5.4 Performance oriented packaqinq (POPI. The exterior pack cited a

12、bove shall meet all of the POP test requirements in accordance with Code of Federal Regulations Title 49 (49 CFR). A POP test report shall be generated in accordance with DI-PACK-81059 following the tests. POP testing may be waived if an acceptable analogy in accordance with 49 CFR, to another pack

13、which has successfully completed the testing, can be made. An analogy must also be documented in accordance with DI-PACK- 81059. When completed, either POP test report must be kept on file by the contractor and must also be submitted to the U.S. Army Research, Development and Engineering Center, ATT

14、N: SMCAR-AEP, Picatinny Arsenal, NJ 07806-5000. (Note: If a POP test report is prepared against an acceptable analogy, the analogy POP test must also be submitted to SMCAR-AEP). The POP marking to be applied to the exterior pack shall be as specified by the government after review and acceptance of

15、the submitted POP test reports. NOTE: The margins of this amendment aremarked with an asterisk or vertical line to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liabil

16、ity whatsoever for . any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian : Army-AR Preparing activity: Army-AR (Project 1375-0001) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-