ARMY MIL-C-63127-1977 MILITARY SPECIFICATION nCARTRIDGES 40MM GROUND SMOKE MARKERS M713 M715 AND M716 BASE PARTS FOR《M713 M715及M716型40MM炮弹地面烟雾标记的基础零件》.pdf

《ARMY MIL-C-63127-1977 MILITARY SPECIFICATION nCARTRIDGES 40MM GROUND SMOKE MARKERS M713 M715 AND M716 BASE PARTS FOR《M713 M715及M716型40MM炮弹地面烟雾标记的基础零件》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-63127-1977 MILITARY SPECIFICATION nCARTRIDGES 40MM GROUND SMOKE MARKERS M713 M715 AND M716 BASE PARTS FOR《M713 M715及M716型40MM炮弹地面烟雾标记的基础零件》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-63127 (PA) 15 February 1977 MILITARY SPECIFICATION CARTRIDGES: 40MM, GROUND, SMOKE MARKERS, M713, M715 AND M716, BASE PARTS FOR This specification is approved for use by Picatinny Arsenal, Department of the Army, and is available for use by all Departments and Agencies of the Department of Def

2、ense. 1. SCOPE 1.1 This specification contains requirements not normally covered by the drawings and provides quality assurance provisions for the fabrication of parts and packing for one type of Base for Cartridges: 40MM, Ground Smoke Markers. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents.-The fo

3、llowing documents of the issue in effect on date of invitation for bids or request for fied herein. proposal, form a part of this specification to the extent speci- SPECIFICATIONS FEDERAL TT-C-490 - Cleaning Methods and Pretreatment of Ferrous Surfaces For Organic Coatings MILITARY MIL-A-48078 - Amm

4、unition, Standard Quality Assurance Provisions, General Specification For STANDARDS FEDERAL FED-STD-141 - Paint, Varnish, Lacquer and Related Materials, Methods of Inspection, Sampling and Testing Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use

5、in improving this document should be addressed to: Commander, picatinny Arsenal, Dover, New Jersey 07801 by using the self-addressed Standard- ization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC: 1310 Provided by IHSNot for ResaleNo reproducti

6、on or networking permitted without license from IHS-,-,-MIL-C-63l127 13 W 7779906 03411281 5 W MiL-(2-63127 (PA) MILITARY MIL-STD-105 - Sampling Procedures and Tables for MIL-STD-1169- Packaging, Packing and Marking for Inspection by Attributes Shipment of Inert Ammunition Components DRAWINGS PICATI

7、NNY ARSENAL 9258730 - Base 3. REQUIREMENTS 3.1 Material.-Materials shall be in accordance with the applicable drawings and specifications. 3.2 Part.-The - part shall comply with all requirements specified on Drawing (Dwg.) 9258230, all associated drawings, and with all requirements specified in appl

8、icable specifications. technical provisions for first article inspection. Requirements for the submission of first article samples by the contractor shall be as specified in the contract. 3.3 First Article Inspection.-This specification contains 3.4 Worknanship.-All parts shall be fabricated and fin

9、ished in a thorough, workmanlike manner. They shall be free of burrs, chips, sharp edges, cracks, unblended radii, surface defects, dirt, grease, rust, corrosion products, and other foreign matter. The cleaning method used shall not be injurious to any parts, nor shall the parts be contaminated by t

10、he cleaning agents. All marking and stamping shall be neat and sharply defined. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection and Standard Qualit Assurance Provisions.-Unless otherwise specified herein oryin the contract, the provisions o-f MIL-A-48078 shall apply and are hereby

11、made a part of this detail specification. 1 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-rl !5 rl MIL-C-b3127 13 W 7777706 0344283 7 = cucu MM 0.

12、 IAIA cu 8 E : 2 B i 5 O c D Y 3 n Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.3.3 Rejection.-See MIL-A-48078. 4.4 Quality Conformance Inspection 4.4.1 Inspection Lot Formation.-Inspection lots shall comply with the lot formation provisions of

13、MIL-A-48078. 4.4.2 Examination.-See MIL-A-48078. a. Sampling Plans.-Unless otherwise specified in the Classification of Defects and Test Tables, sampling plans for major and minor defects shall be an accordance with MIL-STD-105, Inspection Level II . 5 Provided by IHSNot for ResaleNo reproduction or

14、 networking permitted without license from IHS-,-,-rl rl CU * a . K O MIL-C-63127 13 H 7777906 03L111285 2 H rl CUCUCU CUCU* MMM MMM . . &?“ O00 uuu =i-* ooo O00 O00 . . a . .rl k a, a 2 ai z 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T MIL-C-

15、63127 13 U 7777706 03Li428b Lt W L M * * a h cd .rl GI k al a 2 m a, 9 d cd ul R E Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b3127 13 W 777970b 03Y4287 b W MIL-C-63127 (PA) 4.4.3 4.4.4 Inspection Equipment.-The inspection equipment requir

16、ed Testing.-Testing is described in the First Article and Quality Conformance Inspection Tables. to perform the examinations and tests prescribed herein is described in the Paragraph Reference/Inspection Method column in the tables starting with Paragraph 4.4.2.1. The contractor shall submit for app

17、roval inspection equipment designs in accordance with the terms of the contract. See Section 6 of MTL-A-48078 and 6.3 herein. 4.5 Test methods and procedure 4.5.1 Dimehsional control of cast parts.-In place of the normal sampling associated with the Classification of Defects, and with the approval o

18、f the Contracting Officer, a sample of at least three (3) parts (as cast) from each cavity shall be dimensionally inspected to qualify a new or reworked cavity for use in production or as a control of the cavity during pro- duction. duction shall be performed on the above.quantities from each cavity

19、 after production of 5000 parts. identification must be provided. If any defective parts are found during qualification of the cavity, the cavity producing the defective part shall not be used in production. If any defective parts are found when inspection is performed for control of the cavity, the

20、 cavity producing the defective part shall be removed from production. Further, that portion of production since the last control check shall be returned to the contractor for corrective action. All cavities formerly removed from production because of some fault, may, after reworking, be returned to

21、 production providing they pass the qualification test specified above. contractor may request a change of inspection frequency pro- viding he presents objective evidence to substantiate the re- quest to the Contracting Officer. cordance with FED-STD-141. Inspection for control of each cavityhring p

22、ro- Individual cavity The 4.5.2 Salt spray.-This test shall be conducted in ac- PACKAGIBIG 5.1 Preservation aHd pacha-finq 5.1.1 Levei C.-The base shall be preserved and packaged in * accordance with MIL-STD-1169. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

23、 from IHS-,-,-5.2 MIL-C-63127 13 7777706 03Li42 W MIL-C-63127 (PA) Packhg 5.2.1 Level C.-The base, preserved and packaged as specified in 5.1.1, shall be packed for shipment in accordance with MIL-STD- 1169 . 5.3 Marking.-Marking of the carton shall comply with MIL-STD- 1169. 5.4 Shipping.-When comp

24、onents from more than one lot are shipped as a carload, each lot shall be kept separate, and the division between lots clearly indicated to prevent mixing of the lots in transit. 6. NOTES 6.1 Intended Use.-The component covered by thisspecification is intended for use on Cartridges: 40MM, Ground Smo

25、ke Markers, M713, M175 and M716. 6.2 Ordering Data.-See MIL-A-48078. 6.3 Submission of Inspection Equipiaent Designs for Approval.- See MIL-A-48078. ATTN: DRDAR-QAA-I, ARRADCOM, Dover, New Jersey 07801. Submit equipment designs as required to Commander, Custodian: Project Number: 1310-A-098 Army-PA Preparing Activity: Army- PA Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-