ARMY L-P-377C-1994 PLASTIC SHEET AND STRIP POLYESTER.pdf

《ARMY L-P-377C-1994 PLASTIC SHEET AND STRIP POLYESTER.pdf》由会员分享，可在线阅读，更多相关《ARMY L-P-377C-1994 PLASTIC SHEET AND STRIP POLYESTER.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、L-P-377c = 9999974 OLb384b 4TT M piGG-1 L-P-377c March 23, 1994 SUPERSEDING L-P-377B February 28, 1966 FEDERAL SPECIFICATION PLASTIC SHEEI AND STRIP, POLYESTER This specification is approved by the Comnissioner, Federal Supply Service, General Services Administration, for the use of all Federal agen

2、cies. 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers polyester-type plastic film. 1.2 Classification. 1.2.1 Ws. Polyester film shall he of the following types, as specified (see 6.2) : W1 - General Purpose Film Type 11 - Highly Transparent Film Type III - Highly Tramparent Film wit

3、h Good Dimensional Type IV - High Tensile-Strength Film with the Greatest Typev - Weatherable Film Possessing Good Transparency Type VI - Heat Shrinkable Film Stability Strength in the Lmgitudinal Direction and Resistance to Outdoor Aging 2. APPLICABLE IxxmEms 2.1 Government documents. The following

4、 documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this document to the extent specified herein. Beneficial comnents (recmndations, additions, deletions) and any pertinent data which my be used in improving this document should be addressed to:

5、U.S. Army Natick Research, Developent, and Engineering Center, Natick, MA 01760-5019 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMS2 N/A FSC 8135 DISTRIBUTION STATEMENT A. Approved for public release; distribution is

6、unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L-P-377c 9999974 OLb3847 336 L-P-377c Federal Specifications: A-A-203 - Paper, Kraft, Wrapping A-A-2601 - Clip, Paper, Wire PPP-B-576 - Boxes, Wood-Cleated Panelboard PPP-B- 6 O 1 - Boxes, Wo

7、od, Cleated-Plywood Federal Standards : FED-SID-123 - Marking for Shipnent (Civil Agencies) (Activities outside the Federal Government may obtain copies of Federal Specifications, Standards, and Comnercial Item Descriptions as outlined under General Information in the Index of Federal Specifications

8、, Standards, and Comnercial Item Descriptions. The Index, which includes cumulative monthly supplements as issued, is for sale on a subscription basis by the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.) (Single copies of this specification, and other Federal s

9、pecifications and Cmrcial Item Descriptions required by activities outside the Federal Government for bidding purposes are available without charge from the General Services Administration Business Service Centers in Boston, MA; New York, NY; Philadelphia, PA; Washington, CC; Atlanta, GA; Chicago, I

10、L; Kansas City, Ml; Fort Worth, TX; Houston, TX; Denver, CO; San Francisco, CA; Los Angeles, CA; and Seattle, WA.) (Federal Government activities my obtain copies of Federal Standard- ization documents and the Index of Federal Specifications, Standards, and Cmrcial Item Descriptions from established

11、 distribution points in their agencies.) Military Specification: MIL-L-10547 - Liners, Case and Sheet, Overwrap; Water- Vaporproof or Waterproof, Flexible Military Standards: MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipnent and Storage (Cop

12、ies of military specifications and standards required by contractors in connection with specific procurement functions should be obtained fran the procuring activity or as directed by the contracting officer.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

13、m IHS-,-,-L-P-377c W 9999974 0163848 272 L-P-377c 2.2 Other publications. The following documents form a part of this dxment to the extent specified herein. Unless a specific issue is identified, the issue in effect on date of invitation for bids or request for American Society for Testinq and Mater

14、ials (ASIM) ASTM D 374 - Thickness of Solid Electrical Insulation ASIM D 882 - Tensile Properties of Thin Plastic Sheeting ASTM D 1003 - Haze and Luminous Transmittance of Transparent Plastics ASTM D 3951 - Packaging, Comnercial (Application for copies should be addressed to the American Society for

15、 Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also my be available in or through libraries or other informational service

16、s.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUI

17、- 3.1 Material. The film covered by this specification shall be material be used when practical as long as it meets the requirements of this specification. 3.2 Dimensions and tolerances. 3.2.1 Thickness. The film thickness shall be as specified in table I when tested as specified in 4.2.6. TABLE I.

18、Thickness and tolerances Thickness, Thickness, inch nominal, Type inch Minimum Maximum availability O. 00015 O. 00025 o. 00012 O. 00017 O. 00018 O. 00033 II II, III 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L-P-377c = 9999974 OLb3B49 LO9 L-P-

19、377c TABLE I. Thickness and tolerances (contd) Thickness , Thickness, inch ncminal , Type inch Minimum Maximum availability O. 00035 O. 00050 O. 00065 O. 00075 o. 00100 O. 00150 o. 00200 O. 00300 O. 00500 O. 00750 o * 01000 O. 01400 O. 00023 O. 00035 O. 00052 O. 00052 O. 0007 o. 0011 O. 0016 O. 0027

20、 O. 0040 O. 0061 O. 0083 O. 0118 O. 00046 O. 00064 O. 00078 O. 00097 o. 0012 O. 0017 O. 0024 O. 0033 O. 0059 O. 0089 O. 0115 O. 0162 II, III I, II, III, IV VI II, III, IV I, II, III, IV I, III, IV I, III, v I, III, v I, III, v I, III I, III I 3.2.2 Roll sizes. The film shall be furnished in rolls co

21、nforming to the requirements in tables II, III, and IV. Tolerance shall be _+ 1/16 inch. For roll cores of 1-1/8 inch outside diameter (O.D.), a plastic tube may be used in lieu of a paperboard tube, for durability. TABLE II. Roll cores J/ Film Film type thichess , nominal, inch I II III IV v VI O.

22、00025 O. 00035 O. 00050 O. 00065 O. 00075 o .o0100 O. 00150 o. 00200 O. 00300 O. 00500 O. 00750 o. 01000 O. 01400 - 1/ Roll core inside diameters (I.D.): A = 1-1/8 inches, B = 3 inches, and C = 6 inches. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

23、,-,-L-P-377c M 9999974 DI163850 920 W L-P-377c TABLE III. Roll dimensions and tolerances Roll core Roll width, inches I.D. , Film thickness, Roll O.D., inches nominal, inch inches J/ Minimum Maximum Tolerance 1-1/8 0.0005 1.4 1/2 18 1/32 3 0.0005 type III, 0.0015 inch and 0.002 inch = 57 inches. - 3

24、/ Below 0.001 inch thickness, the minimum roll width is 1-1/2 inches. TABLE IV. Roll splices Roll core I.D., inches Film thickness , 6 (11 inches 6 (14 inches nominal, inch 1-1/8 3 O.D.) J/ O.D.) - 1/ Maximm splices per roll 0.00035 incorrect; illegible; of improper size, location, sequence, or meth

25、od of application MY component missing, damaged, or not as specif ied Inadequate application of ccmponent, such as: incqlete sealing or closure of flap, improper taping, loose strapping, or inadequate stapling Number per container is mre or less than required 4.2.8 Palletization examination. The ful

26、ly packaged and palletized end items shall be examined for the defects listed belaw. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged. The inspection level shall be S-1 and the finding of any defect shall be cause fo

27、r rejection of the lot. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L-P-377c 999997Y 0363857 285 L-P-377c Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirement Palletization Pallet pattern not as spe

28、cified lmd .not bonded as specified Weight Exceeds maximum load limits Marking mtted; incorrect; illegible; of improper size, location, sequence, or method of application 4.3 Methods of inspection. 4.3.1 Standard conditioninq. Unless otherwise specified herein, or applicable test method, samples for

29、 test shall be conditioned at a temperature of 73.59 2 2% (23OC f l0C) and a relative humidity of 50 percent f 4 percent for a period of not less than 16 hours. 4.3.2 Thickness. Thickness of the film shall be determined in accordance with ASIM D 374, method A or C. For films with a nominal thickness

30、 of 0.00015, 0.00025, and 0.00035-inch, the thickness shall be measured by the above method; however, the film shall be built up by using the number of plies specified below and dividing the readings by the number of plies used. Thickness (nominal), inch Number of plies used to determine thickness O

31、. 00015 O. 00025 O. 00035 4 2 2 Measure at 10 randunly selected points from a minimum area of 12 square inches. The average of the 10 readings shall fall within the specified limits. 4.3.3 Dimensional stability, tvDe I, II, III, and V films. The film shrinkage shall be determined on five specimens c

32、onditioned according to 4.3.1 before and after test. The specimens shall be 10 inches by 10 inches by width of slit roll if this dimension is less than 10 inches. Three masurements shall be made in the longitudinal direction (machine direction) and in the transverse direction. All measurements shall

33、 be accurate to 1/32 inch. Specimens shall be tested by freely suspending them in an oven controlled to 150C _+ l0C for type II and V film and 2OO0C _+ l0C for type I and III film. The test period shall be 30 minutes. Specimens are to be cooled and conditioned in accordance with 4.3.1 before measure

34、ments are made. The percent shrinkage shall be canputed fran the 3 measurement average before and after test. 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L-P-377C W 9999974 CIL63858 LLL W L-P-377c shall be determined on five specimens conditio

35、ned in accordance with 4.3.1. 4.3.3.1 Dimensional stability, tvpe IV film only. TLpe IV film shrinkage Before testing, the specimens shall be 1/4 inch by 15 inches and cut so that the long dimension is parallel to the longitudinal direction (machine direction) of the film. Mark a pair of lines 12 in

36、ches apart on each sample. Measure the distance between the lines on specimens conditioned according to 4.3.1 to the nearest O. O1 inch before and after test. Specimens shall be tested by placing a paper clip conforming to Gem pattern, type I, A-A-2601, capacity 1/16 inch at each end and freely susp

37、ending the assembly in an oven controlled to 15OoC _+ 1 OC. The test period shall be five minutes. The percent shrinkage shall be canputed fran the 5 measurement average before and after test. 4.3.3.2 Dimensional stability, tiwe VI film only. Five specimens 5 inches by 5 inches shall be measured to

38、the nearest 0.1 inch and them imnersed in boiling water ( 100C) for 30 seconds. Remove, cool, lay flat, and smooth out wrinkles. Measure the samples to the nearest 0.1 inch. The percent shrinkage shall be calculated as follows: (Original dimension - Final dimension) X 100 = percent shrinkage Origina

39、l dimension 4.3.4 Optical transmittance, type V film only. The optical transmittance shall be determined in accordance with the following procedure. The test equipnt shall be a Bausch E, Imb Spectronic “20“ Colorimeter or equivalent. Five test specimens, randcanly selected fran the roll, shall be cu

40、t to 3/4 inch by 2 inches. The procedure is to allow the instrument to warm up. The wavelength control shall be set to 400 millimicrons. Adjust the instrument to read zero transmittance. Insert an mpty specimen holder into the 1 inch test tube adapter and adjust the needle to read 100 percent transm

41、ittance. Place a specimen between the holder halves and read percent transmittance. 5. PACKAGING 5.1 Preservation. Preservation shall be level A or CcamEercial, as specified (see 6.2). 5.1.1 &vel A. 5.1.1.1 Rolls. Plastic shall be rolled on a convolute or spiralwund chipboard or plastic tube. Each r

42、oll shall be wrapped with 30 pound minimum basis weight kraft paper conforming to A-A-203, or plastic film 0.002 inch minimum thickness. The roll shall be wrapped so that the wrap canpletely encircles the roll at least once with a minimum overlap of 3 inches, and the width of the wrap shall be suffi

43、cient to fold over and protect the ends of the roll. The wrapping shall be secured with tape. 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L-P-377c m 9999974 OLb3859 058 m L-P-377c 5.1.1.2 Flat cuts. Five hundred sheets, of one type, thickness

44、and size, shall be stacked on a fiberboard pad. The bundle shall be wrapped in 30 pound minimum basis weight kraft paper conforming to A-A-203, or plastic film 0.002 inch minimum thickness. Wrapping shall be secured with tape. 5.1.2 Carmercial preservation. Plastic shall be preserved in accordance w

45、ith ASIM D 3951. 5.2 Packing. Packing shall be level A, B or Carmercial, as specified (see 6.2). 5.2.1 Level A. Plastic, preserved as specified, shall be packed in a wood-cleated plywood box conforming to overseas type, grade A, type 3 load of PPP-B-601, wood-cleated fiberboard box conforming to typ

46、e III, class 2, style A, type II load of PPP-B-576, or a wood-cleated veneer box conforming to type I, class 2, style A, type II load of PPP-B-576. Boxes shall be closed and strapped. 5.2.2 &vel B. Plastic, preserved as specified, shall be packed in a wood-cleated plywood box conforming to domestic

47、type, grade A of PPP-B-601, wood-cleated fiberboard box conforming to type III, class 1, style A, type II load of PPP-B-576, or a wood-cleated veneer box conforming to type I, class 1, style A, type II load of PPP-B-576. Boxes shall be closed and strapped. 5.2.3 Comercial wckinq. Plastic, preserved

48、as specified, shall be packed in accordance with ASIM D 3951. 5.3 Palletization. Plastic, packed as specified, shall be plletized on a 4-way entry pallet in accordance with MIL-SID-147. Each prepared load shall be bonded with straps in accordance with bonding means C and D or film bonding F or G. 5.

49、4 Marking. Marking of unit packs, shall be in accordance with MIL-STD-129 (This setion contains information of may be helpful, but is not mandatory.) shipping containers and unit loads or FED-STD-123. a general or explanatory nature that 6.1 Intended use. The polyester film covered by this specification is intended for general usage in packaging and industrial applications. 6.2 Acquisition requirements. Acquisition documents must specify