ANSI UL 60730-2-14-2013 UL Standard for Safety Automatic Electrical Controls for Household and Similar Use Part 2 Particular Requirements for Electric Actuators (Second Edition Rep.pdf

《ANSI UL 60730-2-14-2013 UL Standard for Safety Automatic Electrical Controls for Household and Similar Use Part 2 Particular Requirements for Electric Actuators (Second Edition Rep.pdf》由会员分享，可在线阅读，更多相关《ANSI UL 60730-2-14-2013 UL Standard for Safety Automatic Electrical Controls for Household and Similar Use Part 2 Particular Requirements for Electric Actuators (Second Edition Rep.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 60730-2-14 Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Electric Actuators STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR F

2、URTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Electri

3、c Actuators, UL 60730-2-14 Second Edition, Dated February 27, 2013 Summary of Topics This revision of ANSI/UL 60730-2-14 is being issued to reaffirm approval as an American National Standard. No changes in requirements are involved. Text that has been changed in any manner or impacted by ULs electro

4、nic publishing system is marked with a vertical line in the margin. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL.

5、UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, includin

6、g loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price pa

7、id for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any

8、error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. JUNE 6, 2017 UL 60730-2-14 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 6, 2017 UL 60730-2-14 tr2 No Text on This P

9、ageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 27, 2013 (Title Page Reprinted: June 6, 2017) 1 UL 60730-2-14 Standard for Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Electric

10、Actuators Prior to the rst edition of UL 60730-2-14, the requirements for the products covered by this Standard were included in UL 8730-2-14. First Edition February, 2002 Second Edition February 27, 2013 This ANSI/UL Standard for Safety consists of the Second Edition including revisions through Jun

11、e 6, 2017. The most recent designation of ANSI/UL 60730-2-14 as a Reaffirmed American National Standard (ANS) occurred on June 6, 2017. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page or Preface. The National Difference Page and IEC Foreword are also exclu

12、ded from the ANSI approval of IEC-based standards. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. ULs Standards for S

13、afety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2017 UNDERWRITERS LABORATORIES INC. A

14、NSI/UL 60730-2-14-2013 (R2017)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 27, 2013 UL 60730-2-14 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CO

15、NTENTS Preface (UL) 6 NATIONAL DIFFERENCES . 7 FOREWORD 8 1 Scope and normative references .11 2 Denitions 12 2.2 Denitions of types of control according to purpose 12 2.3 Denitions relating to the function of controls .13 2.13 Miscellaneous denitions 13 3 General requirements .13 4 General notes on

16、 tests .13 5 Rating 13 6 Classication 13 6.1 According to nature of supply 13 6.3 According to their purpose 14 6.4 According to features of AUTOMATIC ACTION 14 6.11 According to number of automatic cycles (A) of each AUTOMATIC ACTION .15 7 Information 15 8 Protection against electric shock .16 9 Pr

17、ovision for protective earthing .16 10 Terminals and TERMINATIONS .16 11 Constructional requirements 16 11.4 Actions .16 12 Moisture and dust resistance .17 13 Electric strength and insulation resistance 17 14 Heating 17 15 MANUFACTURING DEVIATION and DRIFT .18 16 Environmental stress .18 17 Enduran

18、ce 18 17.4 Manual and mechanical conditions for the tests .18 17.6 Not applicable. 19 18 Mechanical strength .19 19 Threaded parts and connections 19 20 CREEPAGE DISTANCES, CLEARANCES and distances through solid insulation .19 21 Resistance to heat, re and tracking .19 22 Resistance to corrosion 19

19、23 Electromagnetic compatibility (EMC) requirements Emission 19 24 Components 19 25 Normal OPERATION 19 26 Electromagnetic compatibility (EMC) requirements Immunity 19 27 Abnormal OPERATION 20 27.2 Blocked output test (temperature) 20 27.3 Not applicable. 21 28 Guidance on the use of electronic disc

20、onnection 21 FEBRUARY 27, 2013 UL 60730-2-14 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figures Annexes Annex D (informative) Heat, re and tracking (applicable in Canada and the USA) D.2 Polymeric materials used for enclosures for port

21、able, stationary and xed controls . . . .23 Annex H (normative) Requirements for ELECTRONIC CONTROLS H.11 Constructional requirements .24 H.26.1 Addition: .24 H.26.5 Voltage dips and voltage interruptions in the power supply network .24 H.26.6 Not applicable. 25 H.26.8 Surge immunity test .25 H.26.9

22、.3 Test procedure 25 H.26.10 Ring wave test .26 H.26.13 Test of inuence of supply frequency variations .26 H.26.14 Power frequency magnetic eld immunity test 26 H.26.15.4 .27 ANNEX DVC Markings FEBRUARY 27, 2013 UL 60730-2-14 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRI

23、BUTION WITHOUT PERMISSION FROM UL FEBRUARY 27, 2013 UL 60730-2-14 5 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface (UL) This UL Standard, UL 60730-2-14, Standard for Automatic Electrical Controls for Household an

24、d Similar Use; Part 2: Particular Requirements for Electric Actuators, is to be used in conjunction with UL 60730-1. The requirements for electric actuators are contained in this part 2 standard and UL 60730-1. Requirements of this Part 2 Standard, where stated, amend the requirements of UL 60730-1.

25、 Where a particular subclause of UL 60730-1 is not mentioned in UL 60730-2-14, the UL 60730-1 subclause applies. The text, gures and tables of the IEC Standard for Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Electric Actuators, 60730-2-14, copyrig

26、ht 1995 as amended in 2001 and 2007 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission from ANSI. ANSI should be contacted regarding the reproduction of any portion of the IEC ma

27、terial. The IEC Foreword and Introduction are not a part of the requirements of this Standard but are included for information purposes only. Copies of IEC Publication 60730-2-14 may be purchased from ANSI, 25 West 43rd Street, 4th Floor, New York, NY 10036, (212) 642-4900. Note Although the intende

28、d primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose. These materials are subject to copyright claims of IEC and UL. No part of this publication may

29、 be reproduced in any form, including an electronic retrieval system, without the prior written permission of UL. All requests pertaining to the UL 60730-2-14 standard should be submitted to UL. JUNE 6, 2017 UL 60730-2-14 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTI

30、ON WITHOUT PERMISSION FROM UL NATIONAL DIFFERENCES GENERAL National Differences from the text of International Electrotechnical Commission (IEC) Publication 60730-2-14, Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Electric Actuators, copyright 2007

31、, are indicated by notations (differences) and are presented in bold text. There are ve types of National Differences as noted below. The difference type is noted on the rst line of the National Difference in the standard. The standard may not include all types of these National Differences. DR Thes

32、e are National Differences based on the national regulatory requirements. D1 These are National Differences which are based on basic safety principles and requirements, elimination of which would compromise safety for consumers and users of products. D2 These are National Differences from IEC requir

33、ements based on existing safety practices. These requirements reect national safety practices, where empirical substantiation (for the IEC or national requirement) is not available or the text has not been included in the IEC standard. DC These are National Differences based on the component standar

34、ds and will not be deleted until a particular component standard is harmonized with the IEC component standard. DE These are National Differences based on editorial comments or corrections. Each national difference contains a description of what the national difference entails. Typically one of the

35、following words is used to explain how the text of the national difference is to be applied to the base IEC text: Addition / Add - An addition entails adding a complete new numbered clause, subclause, table, gure, or annex. Addition is not meant to include adding select words to the base IEC text. M

36、odication / Modify - A modication is an altering of the existing base IEC text such as the addition, replacement or deletion of certain words or the replacement of an entire clause, subclause, table, gure, or annex of the base IEC text. Deletion / Delete - A deletion entails complete deletion of an

37、entire numbered clause, subclause, table, gure, or annex without any replacement text. JUNE 6, 2017 UL 60730-2-14 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTERNATIONAL ELECTROTECHNICAL COMMISSION AUTOMATIC ELECTRICAL CONTROLS FOR HO

38、USEHOLD AND SIMILAR USE Part 2: Particular requirements for electric actuators FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to pr

39、omote international co-operation on all questions concerning standardization in the electrical and electronic elds. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee intereste

40、d in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance wi

41、th conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interes

42、ted National Committees. 3) IEC Publications have the form of recommendation for international use published in the form of standards, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unication, IEC National Committees u

43、ndertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) IEC provides no marking proced

44、ure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agent

45、s including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, o

46、r reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of

47、 the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60730-2-14 has been prepared by IEC technical committee 72: Automatic controls for household use. This consolidated v

48、ersion of IEC 60730-2-14 consists of the rst edition (1995) documents 72/307/FDIS and 72/339/RVD, its amendment 1 (2001) documents 72/480/FDIS and 72/502/RVD and its amendment 2 (2007) documents 72/748/FDIS and 72/756/RVD. The technical content is therefore identical to the base edition and its amen

49、dments and has been prepared for user convenience. FEBRUARY 27, 2013 UL 60730-2-14 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL It bears the edition number 1.2. A vertical line in the margin shows where the base publication has been modied by amendments 1 and 2. The text of these amendments are based on the following documents: FDIS Report on voting 72/480/FDIS 72/502/RVD 72/748/FDIS 72/756/RVD Full information on the voting fo