ANSI UL 2388-2017 UL Standard for Safety Flexible Lighting Products (Second Edition).pdf

《ANSI UL 2388-2017 UL Standard for Safety Flexible Lighting Products (Second Edition).pdf》由会员分享，可在线阅读，更多相关《ANSI UL 2388-2017 UL Standard for Safety Flexible Lighting Products (Second Edition).pdf（45页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 2388 Flexible Lighting Products STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHO

2、RIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Flexible Lighting Products, UL 2388 Second Edition, Dated May 3, 2017 Summary of Topics The Second Edition of ANSI/UL 2388 was issued to include the revision to the weight requirement for the Flexing

3、 Test and the Crimp Connection Secureness Test for conductors smaller than 18 AWG. The revised requirements are substantially in accordance with Proposal(s) on this subject dated August 26, 2016. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or tra

4、nsmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness

5、for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representa

6、tive has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless fro

7、m and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. MAY 3, 2017 UL 2388 tr1UL COPYRIGHTED MATERIAL NOT AUTHOR

8、IZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 3, 2017 UL 2388 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 3, 2017 1 UL 2388 Standard for Flexible Lighting Products First Edition

9、July, 2002 Second Edition May 3, 2017 This ANSI/UL Standard for Safety consists of the Second Edition. The most recent designation of ANSI/UL 2388 as an American National Standard (ANSI) occurred on May 3, 2017. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, and Tit

10、le Page. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. ULs Standards for Safety are copyrighted by UL. Neither a pri

11、nted nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2017 UNDERWRITERS LABORATORIES INC. ANSI/UL 2388-2017UL COPYRIGHTED MATERIAL NO

12、T AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 3, 2017 FLEXIBLE LIGHTING PRODUCTS - UL 2388 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 Compon

13、ents5 3 Units of Measurement .6 4 Undated References 6 5 Glossary .6 CONSTRUCTION 6 Assembly and Packaging 6 7 Enclosures .7 8 Decorative Parts 9 9 Light Sculptures 9 10 Accessibility of Current Carrying Parts9 11 Insulating Materials .11 12 Electrical Spacing.11 13 Lamps.11 14 Conductors 11 15 Spli

14、ces and Connections 12 16 Attachment Plugs .13 17 Interconnecting Means 13 18 Switches, Fuses, and Controllers .14 19 Power Supply Cord and Interconnecting Cords .14 20 Strain Relief15 21 Mounting Means 15 22 Outdoor Use Products.15 23 Class 2 Circuits.15 24 Battery Operated Products .16 PERFORMANCE

15、 25 Input Test17 26 Normal Temperature Test17 27 Abnormal Operation Test 18 28 Insulation Resistance Test .19 29 Dielectric Voltage Withstand Test .19 30 Crush Test .20 31 Ultraviolet (UV) Light Exposure and Water Immersion Tests .21 31.1 General .21 31.2 UV conditioning 21 31.3 Water immersion .22

16、32 Ball Impact Test 22 33 Flexing Test23 34 Oven Conditioning Test24 35 Cold Bend Test.25 36 Strain Relief Test .25 37 Crimp Connection Secureness Test .25 38 End Cap Pull Test 26 39 Rain Test 26 MAY 3, 2017 FLEXIBLE LIGHTING PRODUCTS - UL 2388 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REP

17、RODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 40 Test for Permanence of Cord Tag 27 40.1 General .27 40.2 Test conditions.27 40.3 Test method .28 41 Gasket Test 29 42 Gasket Adhesion Test .29 MANUFACTURING AND PRODUCTION TESTS 43 Production-Line Spark Test 29 44 Operational Test 32 45 Polariz

18、ation Continuity Test 32 RATINGS 46 Rating .33 MARKING 47 General33 48 Outdoor Use Markings 35 49 Battery Operated Product Markings .35 50 Battery Supply Polarity Identication Markings35 INSTRUCTIONS 51 Installation and Use Instructions 36 52 Outdoor Use Instructions 38 53 Packaging Instructions and

19、 Markings38 APPENDIX A Standards for ComponentsA1 MAY 3, 2017 FLEXIBLE LIGHTING PRODUCTS - UL 2388 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 This standard covers portable exible lighting products with a maximu

20、m input voltage rating of 120 volts to be used in accordance with the National Electrical Code, ANSI/NFPA 70. These products are provided with a power supply cord and are intended for outline and decorative lighting use. 1.2 These requirements cover lighting products incorporating non-replaceable se

21、ries and series/parallel connected lamps enclosed within a exible polymeric tube or extrusion. 1.3 These requirements also cover exible lighting products used in light sculptures. 1.4 These requirements do not cover lighting products with replaceable lamps. 1.5 These requirements do not cover the te

22、mporary-use, seasonal decorative-lighting products and accessories with a maximum input voltage rating of 120 V that are covered by the Standard for Seasonal and Holiday Decorative Products, UL 588. 1.6 These requirements do not cover exible lighting products that are intended for use as a sign, suc

23、h as self-contained product, usually with advertising or other words, numbers, or symbols, intended for use in a nonresidential environment to convey information or attract attention. These products shall be covered under the Standard for Electric Signs, UL 48. 2 Components 2.1 Except as indicated i

24、n 2.2, a component of a product covered by this standard shall comply with the requirements for that component. See Appendix A for a list of standards covering components used in the products covered by this standard. 2.2 A component is not required to comply with a specic requirement that: a) Invol

25、ves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.4 Specic comp

26、onents are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. MAY 3, 2017 FLEXIBLE LIGHTING

27、 PRODUCTS - UL 2388 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3 Units of Measurement 3.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 4 Undated References 4.1

28、 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 5 Glossary 5.1 For the purpose of this standard, the following denitions apply. 5.2 EXTENSION SEGMENT A exible lighting produc

29、t intended to be connected to a connector of another exible lighting product and not provided with a means to independently connect to a 120 V supply circuit. 5.3 INTERNAL LAMP SHUNT A device that provides a current path when the lament of a lamp opens so that the remaining lamps in a series-connect

30、ed circuit remain illuminated. 5.4 LIGHT SCULPTURE A polymeric or metallic rigid frame to which a exible light is attached. The exible light provides outline illumination of the gure or object created by the frame. 5.5 NON-EXTENDABLE FLEXIBLE LIGHT A exible light product that is not provided with an

31、y means to add an extension segment. CONSTRUCTION 6 Assembly and Packaging 6.1 A exible lighting product shall be completely wired with each electrical component mounted in place and with each splice and connection completed. 6.2 Detachable power-supply cords and extension segments that comply with

32、Section 17, Interconnecting Means, need not be connected. 6.3 The package for a exible lighting product designed to be connected to its source of supply by means of a detachable power-supply cord shall include the detachable power-supply cord. MAY 3, 2017 FLEXIBLE LIGHTING PRODUCTS - UL 2388 6UL COP

33、YRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 7 Enclosures 7.1 The enclosure shall withstand the abuses that it is subjected to without total or partial collapse of the enclosure, reduction of spacing, loosening or displacement of parts, or othe

34、r defects that increase the risk of re, electric shock, or injury to persons. 7.2 A polymeric material used to enclose or provide structural support for electrical current carrying parts shall: a) Have a minimum ammability rating of V-0; and b) Have a minimum HWI (hot-wire resistance to ignition) Pe

35、rformance Level Category (PLC) of 3, a minimum HAI (high-current arc resistance to ignition) PLC of 3, and a minimum CTI PLC of 4, if marked for indoor use, or a minimum PLC of 3, if marked for outdoor use. Exception No. 1: The minimum ame rating shall be HB when the exible lighting product is locat

36、ed in a Class 2 circuit. Exception No. 2: A exible lighting product whose enclosure is extruded of an insulation compound that is rated 105C, and also complies with the requirements of the VW-1 ame test, and 720 hour weatherometer test, need not comply with 7.2(a) and (b) when the ropelight body com

37、plies with the VW-1 ame test as described in the Reference Standard for Electrical Wires, Cables, and Flexible Cords, UL 1581, and when intended for outdoor use, complies with the VW-1 ame test and crush test after being subjected to the Ultraviolet (UV) Light Exposure and Water Immersion Tests desc

38、ribed in Section 31. 7.3 The polymeric tube or extrusion section of the exible light enclosure that is used to enclose the lamps shall comply with the: a) Crush Test, Section 30; b) Flexing Test, Section 33; and c) Oven Conditioning Test, Section 34. 7.4 There shall be a minimum of 3/64 inch (1.2 mm

39、) of insulating material between uninsulated current carrying parts of the series or series/parallel circuit and the outer surface of the ropelight body. Exception: A ropelight located in a Class 2 circuit need not comply with this requirement. 7.5 A polymeric enclosure for a controller or other acc

40、essory used with a exible light shall comply with the: a) Crush Test, Section 30; b) Ball Impact Test, Section 32; and c) Oven Conditioning Test, Section 34. MAY 3, 2017 FLEXIBLE LIGHTING PRODUCTS - UL 2388 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERM

41、ISSION FROM UL 7.6 The ammability rating specied in 7.2(a) is to be determined by the applicable tests in the Standard for Tests for Flammability of Plastic Materials for Parts in Devices and Appliances, UL 94. 7.7 As an alternative to 7.2(a), the polymeric material is able to comply with the 3/4 in

42、ch or 12 mm ame test of the Standard for Polymeric Materials Use in Electrical Equipment Evaluations, UL 746C. At the conclusion of the test there shall not be openings large enough to enable a 1/4 inch (6.4 mm) diameter rod to penetrate the enclosure and there shall not be ignition of the cotton in

43、dicator. The indicator is to be absorbent, 100 percent cotton thinned to approximately 2 by 2 inches (50 by 50 mm) and a maximum thickness of 0.24 inches (6 mm). The cotton is to be placed horizontally 11.8 0.39 inches (300 10 mm) below the component material. 7.8 With regard to consideration of the

44、rmal endurance in the Standard for Polymeric Materials Use in Electrical Equipment Evaluations, UL 746C, the material shall possess a mechanical temperature index, with impact, as a result of long term aging or a generic temperature index of at least the measured temperature in the Normal Temperatur

45、e Test, Section 26. 7.9 The temperature index specied in 7.8 shall include temperatures measured on polymeric materials closest to or in direct contact with any lamp. 7.10 An enclosure formed of polymeric material and marked for outdoor use in accordance with Section 48, Outdoor Use Markings, shall

46、comply with: a) The UV resistance and water exposure requirements from the Standard for Polymeric Materials Use in Electrical Equipment Evaluations, UL 746C; b) The Rain Test, Section 39; and c) For an enclosure of a exible light, the Cold Bend Test, Section 35. 7.11 As an alternative to 7.10(a), a

47、polymeric material may be employed as an enclosure of a exible lighting product marked for outdoor use provided it complies with the ammability rating evaluation of 7.6 or 7.7 as applicable, the Crush Test, Section 30, and the Ball Impact Test, Section 32, after being subjected to the Ultraviolet (U

48、V) Light Exposure and Water Immersion Tests described in Section 31. The end-product test force and impact values shall be reduced by 30 percent after the UV light exposure test, and reduced by 50 percent after the water immersion test. At the conclusion of the conditioning and end-product tests, th

49、e ammability rating shall not be reduced and the samples shall comply with the requirements of 30.3 and 32.6. The ball impact test is only applicable to a controller or other accessory used with a exible light. 7.12 If a exible light enclosure consists of multiple layers of polymeric materials, all layers shall comply with 7.2 and only the outermost layer needs to comply with the UV resistance and water exposure requirements of 7.10(a), providing that the material used for the outermo