ANSI UL 1610-1998 UL Standard for Safety Central-Station Burglar-Alarm Units (Third Edition Reprint with Revisions Through and Including March 20 2015).pdf

《ANSI UL 1610-1998 UL Standard for Safety Central-Station Burglar-Alarm Units (Third Edition Reprint with Revisions Through and Including March 20 2015).pdf》由会员分享，可在线阅读，更多相关《ANSI UL 1610-1998 UL Standard for Safety Central-Station Burglar-Alarm Units (Third Edition Reprint with Revisions Through and Including March 20 2015).pdf（132页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1610 Central-Station Burglar-Alarm UnitsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR F

2、URTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Central-Station Burglar-Alarm Units, UL 1610 Third Edition, Dated October 26, 1998 Summary of Topics The revisions were issued to incorporate the following: 1. Revision to minimum spacing requirements. 2. Revis

3、ion to 62A.2, Exception No. 1, item (b) so that a duplicate alarm is optional. 3. Revision to 62A.2, Exception No. 1, item (d) so that it is not limiting. 4. Revision to 62A.6, item (b) to remove redundant language. The revised requirements are substantially in accordance with Proposal(s) on this su

4、bject dated October 7, 2011 and April 11, 2014. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indi

5、cating the date of publication or the date on which the changed requirement becomes effective. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise witho

6、ut prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect o

7、r similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any dama

8、ge ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorney

9、s fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future

10、 effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. The following table lists the future effective dat

11、es with the corresponding reference. MARCH 20, 2015 UL 1610 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Future Effective Date Reference September 20, 2017 Paragraphs 62A.2, 62A.6 March 20, 2018 Table 23.1 MARCH 20, 2015 UL 1610 tr2UL

12、COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 26, 1998 (Title Page Reprinted: March 20, 2015) 1 UL 1610 Standard for Central-Station Burglar-Alarm Units First Edition January, 1985 Second Edition May, 1994 Third Edition October 26, 19

13、98 This ANSI/UL Standard for Safety consists of the Third Edition including revisions through March 20, 2015. The most recent designation of ANSI/UL 1610 as an American National Standard (ANSI) occurred on March 20, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Page

14、s, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety

15、are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL

16、 1610-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SEPTEMBER 10, 2010 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSI

17、ON FROM UL CONTENTS INTRODUCTION 1 Scope .7 2 General 8 2.1 Components .8 2.2 Units of measurement .8 2.3 Undated references .8 2.4 Terminology .8 3 Glossary 8A 4 Installation and Operating Instructions .9 4A Installation and Operating Instructions Physical Media 10 5 Electric Shock 10A CONSTRUCTION

18、 ASSEMBLY 6 General .10A 6.1 Product assembly 10A 6.2 Electrical protection 11 7 Protection of Service Personnel .14 8 Enclosures 14 8.1 General 14 8.2 Doors and covers .15 8.3 Enclosure openings 15 8.4 Screens and expanded metal .18 8.5 Cast metal 19 8.6 Sheet metal 19 8.7 Product enclosure mountin

19、g 22 8.8 Polymeric materials 22 9 Corrosion Protection .22 FIELD WIRING CONNECTIONS 10 General 23 11 Cord-Connected Products .23 12 Permanently-Connected Products .24 12.1 General .24 12.2 Field-wiring terminals .25 12.3 Field wiring leads .27 12.4 Polarity identication 27 13 Grounding .28 INTERNAL

20、WIRING 14 General 29 15 Wiring Methods .29 16 Separation of Circuits .30 17 Bonding for Grounding 30 SEPTEMBER 10, 2010 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL COMPONENTS, ELECTRICAL 18

21、General 34 18.1 Mounting of components 34 18.2 Insulating materials .35 18.3 Fuseholder 36 18.4 Current-carrying parts .36 19 Overcurrent Protection 36 20 Semiconductors 36 21 Switches .36 22 Transformers and Coils 36 SPACINGS 23 General 37 24 Components .40 PERFORMANCE ALL UNITS 25 General 40 25.1

22、Test units and data .40 25.2 Test samples and miscellaneous data 40 25.3 Test voltages .40A 25.4 FCC requirements 40A 26 Normal Operation Test .40A 27 Incorrect Connection Tests .41 28 Input Test 41 29 Output Measurement Test .41 30 Electrical Supervision Test .42 31 Undervoltage Operation Test .42

23、32 Overvoltage Operation Test 43 33 Variable Ambient Test .43 34 Humidity Test 43 35 Leakage Current Tests for Cord-Connected Products .43 36 Electric Shock Current Test 47 37 Overload Test 51 37.1 General .51 37.2 Separately energized circuits 52 38 Endurance Test 52 38.1 General .52 38.2 Separatel

24、y energized circuits 52 39 Jarring Test 53 40 Dielectric Voltage-Withstand Test .54 41 Temperature Test .54 42 Abnormal Operation Test 58 43 Electrical Transient Tests 59 43.1 General .59 43.2 Supply line transients .59 43.3 Internally induced transients .59 43.4 Input/output circuit transients 59 4

25、4 AC Induction Test .62 45 Polymeric Materials Test .63 46 Battery Replacement Test .63 AUGUST 29, 2001 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 47 Drop Test 63 48 Strain Relief Test .63

26、48.1 Supply cord .63 48.2 Field-wiring leads .64 49 Ignition Through Bottom-Panel Opening Tests 64 49.1 General .64 49.2 Hot, aming oil .64 49.3 Molten PVC and copper .65 50 Mechanical Strength Tests for Enclosures .65 51 Special Terminal Assemblies Tests .66 51.1 General .66 51.2 Disconnection and

27、reconnection .66 51.3 Flexing test 66 51.4 Millivolt drop test .66 51.5 Temperature test .67 INTRUSION DETECTION DEVICES 52 General 67 CONTROL UNITS 53 General 67 DIRECT-WIRE SYSTEMS 54 General 67 55 Alarm Receiving Units .68 56 Subscriber Units 68 TRANSMITTER SYSTEMS 57 General 68 57A Dual Signal L

28、ine Transmission Methods .69 58 Central-Station Units 71 59 Subscriber Control Units .72 COMBINATION SYSTEMS 60 General 72 MULTIPLEX SYSTEMS 61 General 73 62 Operation 73 62A Packet Switched Data Networks .76 63 Central-Station Units 78 64 Subscriber Control Units .78 65 Automated System Units 78 66

29、 Satellite Stations 78A 67 Private Radio Facilities .78A DECEMBER 13, 2004 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610 4AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL ACKNOWLEDGMENT SIGNAL 68 General 78B 69 Attack Tests 78C 70 Compromise

30、 Test .78D 70A Encrypted Line Security Equipment 78E POWER SUPPLIES GENERAL 71 Common Requirements 78F RECHARGEABLE (SECONDARY) BATTERIES 72 General 79 NONRECHARGEABLE (PRIMARY) BATTERIES 73 General 80 PERFORMANCE 74 Power Failure 80 SHORT RANGE RADIO FREQUENCY (RF) DEVICES 75 General 82 76 Time to

31、Report Alarm .82 77 Inoperative Transmitter Reporting .83 78 Battery Status Indication .83 79 Tamper Protection 84 80 Interference Protection 84 81 Reference Level Determination .84 81.1 Method 1 84 81.2 Method 2 87 82 Interference Immunity .89 83 Frequency Selectivity 91 84 Clash 91 85 Clash Error

32、92 86 Error (Falsing) Rate .92 87 Throughput Rate 94 88 Transmitter Stability Test 95 89 Transmitter Accelerated Aging Test .95 90 Installation Instructions and User Manual 95 MANUFACTURING AND PRODUCTION-LINE TESTS FOR HIGH-VOLTAGE PRODUCTS 91 General 95 92 Production-Line Dielectric Voltage-Withst

33、and Test 96 93 Production-Line Grounding Continuity Test .96 DECEMBER 13, 2004 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610 4BUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARKING 94 General 97 95 Marking Permanency Tests 99 ACCESSORY EQU

34、IPMENT 96 General 99 97 Construction 100 98 Performance (Installation) Test 100 99 Marking 100 APPENDIX A Standards for ComponentsA1 AUGUST 29, 2001 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM

35、UL This page intentionally left blank. DECEMBER 13, 2004 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover components of central-station burglar-a

36、larm systems intended and specically designated for burglary-protection use at mercantile and banking premises, on mercantile safes, and on bank safes and vaults. 1.2 The components covered by these requirements are intended for use in a burglar-alarm system in which the operations of electrical pro

37、tection circuits and devices are transmitted automatically to, recorded in, maintained from, and supervised from a central-station that employs trained operators and alarm investigators who are in attendance at all times. 1.3 These requirements serve as the basis of classication of central-station b

38、urglar-alarm system transmission methods. The systems may be classied as either standard line security equipment or encrypted line security equipment by virtue of the construction and performance requirements for components of that system. However, requirements covering the complete systems are cont

39、ained in the Standard for Central-Station Alarm Services, UL 827. Revised 1.3 effective December 13, 2006 1.4 Protective devices installed on individual properties are further classied as to extent of protection at each location, according to the requirements covering installation and classication (

40、of extent) of alarm protective equipment at individual locations as published in the Standard for Installation and Classication of Burglar and Holdup Alarm Systems, UL 681. Revised 1.4 effective December 13, 2006 1.5 If equipment covered by these requirements is intended for use in a combination bur

41、glar-alarm and re-protective signaling system, the portion of the equipment serving a re-alarm function is covered by the Standard for Control Units for Fire-Protective Signaling Systems, UL 864. 1.6 Systems covered by these requirements operate using Class 2 remote-control and signaling circuits as

42、 dened by Article 725 of the National Electrical Code, NFPA 70. 1.7 The requirements assume that standard telephone operating practices are acceptable for leased or other lines connecting to a central-station as dened by Article 800 of the National Electrical Code, NFPA 70. 1.8 Deleted August 29, 20

43、01 DECEMBER 13, 2004 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply w

44、ith the requirements for that component. See Appendix A for a list of standards covering components used in the products covered by this standard. 2.1.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of th

45、e component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in construction features or restricted in p

46、erformance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.2 Units of measurement 2.2.1 If a value for measurement is followed by an equivalent value i

47、n other units in parentheses, the second value may be only approximate. The rst stated value is the requirement. 2.2.2 Unless otherwise indicated, all voltage and current values specied in this standard are rms. 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in th

48、e requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 2.4 Terminology 2.4.1 The term product as used in this standard refers to all types of central-station burglar-alarm units. AUGUST 29, 2001 CENTRAL-STATION BURGLAR-ALARM UNITS - UL 1610

49、8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3 Glossary 3.1 For the purpose of this standard, the following denitions apply. 3.1.1 ACKNOWLEDGMENT SIGNAL An audible and/or visual signal that is sent to the subscriber by the central station to notify the subscriber that a signal has been received indicating that the protection system has been properly armed. The acknowledgment signal can be sent manually or automatically. 3.1.1 added Decemb