ANSI UL 1598C-2014 UL Standard for Safety Light-Emitting Diode (LED) Retrofit Luminaire Conversion Kits (First Edition Reprint with revisions through and including July 12 2017)《发光.pdf

《ANSI UL 1598C-2014 UL Standard for Safety Light-Emitting Diode (LED) Retrofit Luminaire Conversion Kits (First Edition Reprint with revisions through and including July 12 2017)《发光.pdf》由会员分享，可在线阅读，更多相关《ANSI UL 1598C-2014 UL Standard for Safety Light-Emitting Diode (LED) Retrofit Luminaire Conversion Kits (First Edition Reprint with revisions through and including July 12 2017)《发光.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1598C Light-Emitting Diode (LED) Retrot Luminaire Conversion Kits STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM U

2、LUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Light-Emitting Diode (LED) Retrot Luminaire Conversion Kits, UL 1598C First Edition, Dated January 16, 2014 Summary of Topics This revision of ANSI/UL 1598C was issu

3、ed to incorporate the additional requirements for LED stage and studio luminaire retrot kits. The new and revised requirements are substantially in accordance with Proposal(s) on this subject dated May 26, 2017. Text that has been changed in any manner or impacted by ULs electronic publishing system

4、 is marked with a vertical line in the margin. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Stan

5、dard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost

6、 savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard,

7、 regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation in

8、troduced while purchaser is storing an electronic Standard on the purchasers computer system. JULY 12, 2017 UL 1598C tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 12, 2017 UL 1598C tr2 No Text on This PageUL COPYRIGHTED MATERIAL NO

9、T AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL January 16, 2014 (Title Page Reprinted: July 12, 2017) 1 UL 1598C Standard for Light-Emitting Diode (LED) Retrot Luminaire Conversion Kits First Edition January 16, 2014 This ANSI/UL Standard for Safety consists of the

10、First Edition including revisions through July 12, 2017. The most recent designation of ANSI/UL 1598C as an American National Standard (ANSI) occurred on July 12, 2017. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, and Title Page. Comments or proposals for revision

11、s on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard shou

12、ld be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2017 UNDERWRITERS LABORATORIES INC. ANSI/UL 1598C-2017UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR D

13、ISTRIBUTION WITHOUT PERMISSION FROM UL JULY 12, 2017 UL 1598C 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope 4A 2 Components5 3 Units of Measurement .5 4 Undated References 5 5 Glossary .5

14、 MECHANICAL CONSTRUCTION 6 General .6 7 Polymeric Materials .6 8 Adhesives6 9 Metal Thickness 7 ELECTRICAL CONSTRUCTION 10 General.7 11 Grounding 7 12 Wiring and Conductors .7 13 LED Components 8 14 Power Supplies, LED Drivers, and Transformers.8 14.1 General 8 14.2 Power supplies8 14.3 Transformers

15、 .8 14.4 LED arrays and modules .9 PERFORMANCE 15 General.9 MARKING AND INSTRUCTIONS 16 General.9 17 Identication .11 18 Installation Marking .12 19 Installation Instructions 12 19.1 General requirements for all luminaire conversions .12 19.2 Specic requirements for uorescent lamps to LED conversion

16、s .14 SUPPLEMENT SA - ADDITIONAL REQUIREMENTS FOR LED RETROFIT CONVERSION KITS FOR MARINE LUMINAIRES SA1 Scope SA1 SA2 GlossarySA1 SA3 General Requirements .SA1 SA4 Additional Markings and Instructions .SA2 JULY 12, 2017 UL 1598C 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DI

17、STRIBUTION WITHOUT PERMISSION FROM UL SUPPLEMENT SB - ADDITIONAL REQUIREMENTS FOR LED RETROFIT CONVERSION KITS FOR STAGE AND STUDIO LUMINAIRES SB1 Scope SB1 SB2 GlossarySB1 SB3 General Requirements .SB1 SB4 Additional Markings and Instructions .SB2 APPENDIX A Standards for ComponentsA1 JULY 12, 2017

18、 UL 1598C 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements apply to light-emitting diode (LED) retrot luminaire conversion kits that are intended to replace existing light sources and systems inclu

19、ding incandescent, uorescent, induction, and high intensity discharge (HID) light sources in previously installed luminaires that already comply with the requirements in the Standard for Luminaires, UL 1598. The kits are intended for use on: a) Luminaires where specic luminaire model or part numbers

20、 are identied in the kit installation instructions; or b) One or more generic type luminaires that meet specic criteria identied in the installation kit instructions. 1.2 This standard contains requirements that supplement the luminaire requirements contained in the Standard for Luminaires, UL 1598,

21、 that apply to the retrot kit and the luminaire. 1.3 LED retrot kits covered by these requirements include but are not limited to LED lamps and arrays, LED control modules, LED drivers, LED power supplies, wiring, lampholders, brackets, wire connectors, reectors, diffusers, and other associated mech

22、anical, electrical, or optical devices. 1.4 This standard does not cover luminaire reector kits covered by the Standard for Supplemental Requirements for Luminaire Reector Kits for Installation on Previously Installed Fluorescent Luminaires, UL 1598B. 1.5 This standard does not cover luminaire conve

23、rsion lamps that are intended to replace existing lamps without any modication, rewiring, or component replacement in the luminaire other than direct replacement of the lamp using the existing lampholder. Requirements for these direct replacement lamps are specied in the Standard for Self-Ballasted

24、Lamps and Lamp Adapters, UL 1993. 1.6 This standard does not cover retrot luminaire conversion kits for amateur movie lights; aquarium lights, cabinet lights, decorative lighting strings, combination fan/IR lamps used for heating, electric signs, exit signs, junction boxes for swimming pool xtures,

25、lamp adapters, low-level path marking and lighting systems, low-voltage landscape lighting, low voltage lighting xtures for use in recreational vehicles, low voltage marine lighting, luminaires for hazardous locations, luminaires for recreational vehicles, marine navigational lights, portable electr

26、ic displays, portable hand lamps, portable luminaires, portable sun/heat lamps, self-ballasted lamps and lamp adapters, submersible luminaires, swimming pool luminaires, temporary lighting strings, therapeutic lamps, track lighting systems, under-cabinet lights and cord-connected under-cabinet light

27、s, and unit equipment for emergency lighting. 1.7 Additional requirements for LED retrot luminaire conversion kits intended for marine luminaires (marine-type xtures) are in Supplement SA. 1.8 Additional requirements for LED retrot luminaire conversion kits intended for stage and studio luminaires a

28、re in Supplement SB. JULY 12, 2017 UL 1598C 4AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NOVEMBER 17, 2016 UL 1598C 4B No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSIO

29、N FROM UL 2 Components 2.1 Except as indicated in this clause, a component of a product covered by this standard shall comply with the requirements for that component. See the Standards for Components appendix for a list of standards covering components generally used in the products covered by this

30、 standard. 2.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.3 A component shall be used

31、in accordance with its rating established for the intended conditions of use. 3 Units of Measurement 3.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 4 Undated References 4.1 Any undated reference to a code or standard appea

32、ring in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 5 Glossary 5.1 For the purposes of this standard, the following denitions apply. 5.2 RETROFIT LUMINAIRE CONVERSION The act of modifying, with additional parts, a luminaire that

33、 was already manufactured and in service in order to convert the luminaire to an LED light source, from an incandescent, uorescent, induction, or high intensity discharge light source. For purposes of this standard, direct replacement of an incandescent, uorescent, induction, or high intensity disch

34、arge lamp to LED lamp, without any electrical or mechanical changes, is not considered to be a luminaire conversion. 5.3 RETROFIT KIT In the context of these requirements, a kit includes all component parts needed, including instructions, for retrot luminaire conversion. JANUARY 16, 2014 UL 1598C 5U

35、L COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MECHANICAL CONSTRUCTION 6 General 6.1 After installation of the retrot kit, a luminaire shall comply with the requirements in Mechanical Construction, Section 5, of the Standard for Luminaires,

36、UL 1598. Exception: Retrot kits for stage and studio luminaires shall comply with requirements in Supplement SB. 6.2 After installation of a retrot kit, all components of the retrot kit and all components of the luminaire that were affected by the installation of the retrot kit shall be secured in p

37、lace so that lamp replacement, inspection of splices to the branch-circuit supply wires, and routine maintenance will not loosen components or joints in the assembly. 7 Polymeric Materials 7.1 A polymeric material serving to complete the enclosure required in Enclosures, Section 5.3, of the Standard

38、 for Luminaires, UL 1598, or providing structural support for any electrical component or for any non-electrical component weighing more than 3 ounces (85 g) shall comply with the requirements in Polymeric Materials, Section 5.7, of UL 1598. Exception: Retrot kits for stage and studio luminaires sha

39、ll comply with requirements in Supplement SB. 7.2 A metallized polymeric reector that is spaced within 3 inches (76.2 mm) from any lampholder, lamp contact, lampholder lead, wiring, or other electrical component that are below the metallized surface shall comply with the applicable requirements for

40、metallized plastic parts in the Standard for Polymeric Materials Use in Electrical Equipment Evaluations, UL 746C. 8 Adhesives 8.1 Except as noted in 8.2, an adhesive or adhesive tape shall not be relied upon to secure any part to a panel, bracket, or component of a luminaire. 8.2 An adhesive or adh

41、esive tape that complies with the requirements for temperature, humidity, and indoor cyclic conditioning for adhesives in the Standard for Polymeric Materials Use in Electrical Equipment Evaluations, UL 746C, may be relied upon to secure a part of a retrot kit to another part of a retrot kit. With r

42、egard to the temperature conditioning, a normal operating temperature of 90C (194F) shall be assumed unless temperature testing of the luminaire/kit combination indicates that a lower normal operating temperature applies. This requirement applies to all adhesives including an adhesive used to secure

43、 a metal foil reecting surface or a laminate reecting surface to the reector base material. JULY 12, 2017 UL 1598C 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 9 Metal Thickness 9.1 Metal parts of a retrot kit and those portions of a lum

44、inaire affected by installation of the retrot kit shall comply with the requirements in Metal Thickness for Enclosures, Section 5.5, of the Standard for Luminaires, UL 1598. Exception: Retrot kits for stage and studio luminaires shall comply with requirements in Supplement SB. ELECTRICAL CONSTRUCTIO

45、N 10 General 10.1 After installation of a retrot kit, a luminaire shall comply with the requirements in Electrical Construction, Section 6, of the Standard for Luminaires, UL 1598. Exception: Retrot kits for stage and studio luminaires shall comply with requirements in Supplement SB. 11 Grounding 11

46、.1 Except as noted in 11.2, an electrically conductive part of the retrot kit spaced within 3 inches (76.2 mm) from all lampholders, lamp contacts, lampholder leads, wiring, and other electrical components shall be connected to an equipment grounding conductor. 11.2 For dead metal parts such as heat

47、 sinks that are integral to the lamp, the need for grounding shall be determined by the basic lamp requirements in the Standard for Self-Ballasted Lamps and Lamp Adapters, UL 1993. 11.3 A connector provided with a contact, or pole, for connection to an equipment grounding conductor shall be arranged

48、 so the grounding connection is the rst to make and the last to disconnect. Exception: This requirement does not apply when the ground path is not needed to reduce the risk of electric shock. 12 Wiring and Conductors 12.1 Supplemental wiring including wires for interconnection of kit components and

49、connectors required for installation of the retrot kit shall be included in the kit. 12.2 The supplemental wiring provided with the retrot kit shall comply with applicable requirements in Electrical Construction, Section 6, of the Standard for Luminaires, UL 1598. Wiring requirements do not apply to integral leads of luminaire components evaluated for use in the retrot kit. Exception: Retrot kits for stage and studio luminaires shall comply with requirements in Supplement SB.