ANSI TIA-455-39-B-1999 FOTP-39 Optical Fiber Cable Water Wicking Test.pdf

《ANSI TIA-455-39-B-1999 FOTP-39 Optical Fiber Cable Water Wicking Test.pdf》由会员分享，可在线阅读，更多相关《ANSI TIA-455-39-B-1999 FOTP-39 Optical Fiber Cable Water Wicking Test.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-455-39-B (Revision of TIA-455-39-A) February 1999FOTP-39 Optical Fiber Cable Water Wicking Test ANSI/TIA-455-39-B-1999 APPROVED: FEBRUARY 8, 1999 REAFFRIMED: MAY 10, 2005 REAFFIRMED: AUGUST 2, 2013 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest throu

2、gh eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications

3、 shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internat

4、ionally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication.

5、 This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations be

6、fore its use. (From Project No. 3-3541-RV2-RF2, formulated under the cognizance of the TIA TR-42 Telecommunications Cabling Systems, TR-42.12 Subcommittee on Optical Fibers and Cables). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology (b) there is no assurance that the Document will b

7、e approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”

8、), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all

9、in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties invo

10、lved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document

11、contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, al

12、ternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of volun

13、tary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s)

14、or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR

15、 IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIM

16、S ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODU

17、CED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES F

18、OR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF TH

19、E USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. - STD-EIA TIA/EIA-455-39B-ENGL 1997 I 3234b00 Ob21973 9T2 FOTP - 39 Optical fiber cable water wicking test Contents . Foreword . I I I I Introduction 1 2 Normative references . I 3 Apparatus 2 4

20、Sampling and specimens . 2 . 5 Procedure . 3 6 Calculations or interpretation of resuits 4 7 8 Documentation .5 Specification information 6 STD-EIA TIA/EIA-455-39B-ENGL 1779 3234600 0623974 839 TW455-39B -FOTP- 39 Optical fiber cable water wicking test Foreword (This foreword is informative only and

21、 is not part of this Standard.) This FOTP is from TTA Standards Proposal No. 3541 I formulated under the cognizance of TIA FO-6.7, Subcommittee on Fiber Optic Cable. This FOTP is part of the series of test procedures included within Recommended Standard EIATlA-455. NOTE - This FOTP was originally pu

22、blished in EIATIA-455-39A as FOTP-39. iii STD.EIA TIA/EIA-455-39B-ENGL 1799 3234b00 0623975 775 W TIA-455-39B FOTP- 39 Optical fiber cable water wicking test I introduction 1.1 Intent This procedure describes the method of measuring the water wicking characteristics of optical fiber cables due to th

23、e hygroscopic nature of the materials contained within the cable. The amount of water wicking is measured in terms of a) the weight of water absorbed by the cable sample and b) the distance from the end of the cable that the water has migrated due to wicking action. 1.2 Scope This procedure is gener

24、ally not intended for use on cables containing water swellable tapes, powders, or yarns. Swellable materials must absorb water in order to swell and build a block to further penetration of water. This test method may be used to look at the water wicking characteristics of such cables, however it mus

25、t be understood that a certain amount of water absorption is necessary for such cables to pass water penetration requirements. 2 Normative references Test or inspection requirements may include, but are not limited to, the following references: EIA/TIA-455-A, Standard test procedures for fiber optic

26、 fibers, cables, transducers, sensors, connecting and teminafing devices, and other fiber optic components. 1 lT-455-39B -7 J 3 Apparatus 3.1 Use a test tube, or similar vessel, suitable to accept the diameter of cable to be tested. 3.2 Use a scale, balance, or platform, accurate to 2 0.05 mg (2 x I

27、O4 oz). 3.3 Use a dye solution, consisting of: Distilled wate; Sod iu m Fluorescein 2 liters (0.52 gal.) 4 g (0.14 oz.) Note 1 - The prepared solution shall be kept stoppered and a fresh solution shall be prepared every 30 days. A new portion of the solution shall be used for each test conducted. .

28、Note 2 - Alternative dyes are permitted if they are ultraviolet detectable and it can be demonstrated that they can be carried in the wicking water. 3.4 Use an ultraviolet light source to detect the presence of the dye solution in the cable sample. The light source shall operate in the absorbance wa

29、velength range for the dye solution being used. 4 Sampling and specimens The test specimen shall be a representative sample of the fiber optic cable. The specimen shall be 150 5 1.5 mm (6 5 0.1 inches) long, unless otherwise specified in the Detail Specification. Trim the lower (immersed) cable end

30、so that it is flat and perpendicular to the cable axis. If necessary, due to the construction of the particular cable under test, prepare the upper end of the sample to ensure that the inner portion(s) of the cable will not fall out when the sample is suspended vertically (see clause 5.2). 2 STDOEIA

31、 TIAIEIA-455-39B-ENGL 1999 3234600 Ob21977 548 W TMIA-455-3 9B 5 Procedure Unless otherwise specified, wicking of an optical fiber cable shall be determined using the procedures specified below. 5.1 A clean specimen shall be weighed accurately to the nearest 0.1 mg (4 x 10“ oz.) for samples which we

32、igh less than 25 g (0.06 Ib) and to the nearest 1 mg (4 x oz.) for samples which weigh 25 g (0.06 Ib) or more. NOTE - Excess filling compound from the end of the cable can be removed before the sample is weighed. 5.2 The weighed specimen shall be suspended vertically with the lower 50 mm (2 inches)

33、immersed in the dye solution in an open test tube or other suitable vessel. The specimen shall remain in this configuration, placed in a draft-free area, for a period of 24 hours. The test conditions shall be standard atmospheric conditions as outlined in ElAilIA-455-A. 5.3 At the end of the test pe

34、riod, the specimen shall be removed from the dye solution. Ensure that no cable filling compound has been left in the test tube. Upon removal, the outer surface of the specimen shall be wiped free of excess moisture using a clean, dry, lint-free cloth. Care should be taken not to wipe off any cable

35、filling compound while wiping off the excess moisture as this will affect the weight measurements. After wiping, and within five minutes after removal from the solution, the specimen shall be weighed again to the nearest 0.1 mg (4 x IO“ oz.) for samples which weigh less than 25 g (0.06 Ib) and to th

36、e nearest I mg (4 x lo5 oz.) for samples which weigh 25 g (0.06 Ib) or more. 5.4 Immediately after the final weighing, the specimen shall be observed under ultra- violet light to determine, to the nearest 1 mm (0.04 inch) the distance the dye solution has traveled in the specimen by wicking action f

37、or each cable component. To facilitate observation, the layer(s) of jacket shall be removed from the specimen and the entire cable dissected working from the upper end of the specimen. 3 STD-EIA TIA/EIA-455-39B-ENGL 1999 = 3234600 Ob2L578 484 TIA/EIA-455-39B 6 Calculations or interpretation of resul

38、ts Subtract the original specimen weight from the final specimen weight, then divide by the original specimen weight to determine the percent change in weight. Change in weight = (Final weiaht - Oriainal weiqht) * (100%) (1) Original weight Dye solution travel = /Wetted distance - immersion lenath)

39、* (100%) (2) immersion length where wetted distance = length (measured from the end of the cable) wetted by the dye (see clause 5.4) immersion length = 50 mm (see clause 5.2) 4 STD-EIA TIA/EIA-455-37B-ENGL 1799 3234600 0621977 310 U TIA/EIA-455-39B 7 Documentation 7.1 The test data sheets shall cont

40、ain the following: 7.1.1 Date of test 7.1.2 Identification of procedure used (FOTP-39 and title) 7.1.3 Identification of the optical fiber cable tested, together with any other applicable data. 3 7.1.4 Test sample length if other than 150 2 1.5 mrn (6 5 0.1 inches). 7.1.6 Test conditions (test durat

41、ion and temperature). 7.1.7 Results of examination. 7.1.7.1 Record the change in weight, calculated as a percentage of the original specimen weighed along with the weight change in grams (weight of water that has wicked). 7.1.7.2 Record the distance the dye solution has traveled beyond the 50 rnm (2

42、 inches) immersion level as a percentage of the immersion depth. 7.2 U.S. Military applications require the following information also be reported with each test. 7.2.1 Names of test personnel. 7.2.2 Test equipment used and date of latest calibration. 5 .9 MIA-455-39B 8 Specification information The

43、 following details shall be specified in the Detail Specification: 8.1 Pretest data required. 8.2 Any deviations to this procedure or any special conditions that apply (specimen length, specimen preparation requirements, test duration and temperature) if other than stated herein. 8.3 Failure criteri

44、a. 8.4 Any other special requirements that may apply. 6 , / THE TELECOMMUNICATIONS INDUSTRY ASSOCIATION TIA represents the global information and communications technology (ICT) industry through standards development, advocacy, tradeshows, business opportunities, market intelligence and world-wide e

45、nvironmental regulatory analysis. Since 1924, TIA has been enhancing the business environment for broadband, wireless, information technology, cable, satellite, and unified communications. TIA members products and services empower communications in every industry and market, including healthcare, education, security, public safety, transportation, government, the utilities. TIA is accredited by the American National Standards Institute (ANSI).