ANSI TIA-455-201-2001 FOTP-201 Return Loss of Connectorized Polarization-Maintaining Fiber or Polarizing Fiber Pigtailed Devices and Cable Assemblies《使用连接器的偏振保持光纤或偏振光纤引线装置和光缆组件的回波损.pdf

《ANSI TIA-455-201-2001 FOTP-201 Return Loss of Connectorized Polarization-Maintaining Fiber or Polarizing Fiber Pigtailed Devices and Cable Assemblies《使用连接器的偏振保持光纤或偏振光纤引线装置和光缆组件的回波损.pdf》由会员分享，可在线阅读，更多相关《ANSI TIA-455-201-2001 FOTP-201 Return Loss of Connectorized Polarization-Maintaining Fiber or Polarizing Fiber Pigtailed Devices and Cable Assemblies《使用连接器的偏振保持光纤或偏振光纤引线装置和光缆组件的回波损.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、TIASTANDARDFOTP-201Return Loss of Connectorized Polarization-Maintaining Fiber orPolarizing Fiber Pigtailed Devices and Cable Assemblies TIA-455-201August 2001 TELECOMMUNICATIONS INDUSTRY ASSOCIATION ANSI/TIA/EIA-455-201-2001 Approved: August 8, 2001 Reaffirmed: April 25, 2008 NOTICETIA Engineering

2、Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product f

3、or their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclu

4、de their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assum

5、e any obligation whatever to parties adopting the Standard or Publication.This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health

6、practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-2761, formulated under the cognizance of the TIA FO-4 Fiber Optics, FO-4.3 Subcommittee on Passive Optical Devices and Components.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATI

7、ON Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search onl

8、ine at http:/www.tiaonline.org/standards/catalog/All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA.Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright

9、 permission to reproduce portions of this document, please contact TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyrightORTelecommunications Industry Associa

10、tion Standards (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Do

11、cument may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs

12、attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensin

13、g terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complie

14、d with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendatio

15、n or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any suc

16、h Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not co

17、nstitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of complia

18、nce with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY

19、THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTEN

20、TS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT,

21、SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

22、 THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA/EIA-455-201iContents1. Introduction . 12. Normative references 33. Apparatus 34. Sampling and specimens . 75. Procedure . 76.

23、Calculation or interpretation of results 117. Documentation 118. Specification information 12ANNEX A. Comparison between this standard and other TIA, IEC or ITU standards13Figure 1. Types of Polarization-Maintaining Fiber 2Figure 2. Steps 5.5 through 5.6 . 9Figure 3. Steps 5.7 and 5.8 9Figure 4. Ste

24、ps 5.9 and 5.10 10Table 1. Wavelength Requirements Of Optical Power Source 4TIA/EIA-455-201iiThis Page Left BlankTIA/EIA-455-201iii_Foreword_This Standard comes from TIA Project No. 4246 and was formulated under thecognizance of TIA subcommittee FO-6.9.This FOTP is part of a series of test procedure

25、s included within RecommendedStandard TIA/EIA-455.This Standard describes a new test method. There is one informative annex to thisStandard.Key words: polarization-maintaining fiber, polarizing fiber, PMF, PZF, return loss, backreflection, interconnection device.TIA/EIA-455-201ivThis Page Left Blank

26、TIA/EIA-455-2011FOTP-201Return Loss of ConnectorizedPolarization-Maintaining or Polarizing FiberPigtailed Devices or Cable Assemblies_1. Introduction_1.1 IntentThis Standard specifies a procedure for the measurement of the return loss of afiber optic interconnection on single mode, highly linearly b

27、irefringent opticalfiber, i.e. either polarization-maintaining (PM) fiber or polarizing (PZ) fiber. Theconnector can be mounted on the PMF/PZF pigtail of a component or part of acable assembly. Return loss, as used in this Standard, is the ratio of powerincident on, or entering the DUT, to the total

28、 power reflected by the DUT,expressed in decibels. The method described in this Standard is the PMF/PZFequivalent of ANSI/TIA/EIA-455-107 with the return loss reported as a positivenumber.Alternately, this measurement is sometimes called “reflectance” for which thevalues are simply the negative of r

29、eturn loss. Thus, “reflectance” is the ratio indecibels of the power reflected by the DUT, to the power incident on, or enteringthe DUT. The preferred terminology is “return loss” as will be used throughoutthe rest of this Standard.1.2 DefinitionsFor the purposes of this Standard, the following defi

30、nitions apply.Birefringence. The property of a material in which orthogonal light polarizationshave different indices of refraction, which cause the light at those polarizationsto travel at different speeds (also referred to as the fast and slow axes). Linearlybirefringent fiber maintains linear pol

31、arization states along the length of the fiber.Unstable birefringence in standard single-mode fiber causes the states ofpolarization to behave in an unpredictable way. Polarization-maintaining fibersare a special class of single-mode fibers with a highly birefringent waveguidestructure that maintain

32、 the polarization states across the length of the fiber.TIA/EIA-455-2012Polarization-Maintaining Fiber (PMF). A class of highly linearly birefringentsingle-mode fiber, unlike the common variety of low birefringence, single-modefiber used in telecommunication networks. PMF is used to guide linearlypo

33、larized light from point to point, that is, to ensure that polarization does notchange with distance. As shown in Figure 1, the birefringence of commercialPMF is stress-induced by placing the core between or within glass elements ofdifferent physical composition, or by forming a non-round core.Polar

34、izing Fiber (PZF). A highly birefringent optical fiber in which only onepolarization state is propagated with low attenuation.Principal Optical Axes. Those optical axes for which the speed of light in alinearly birefringent material is a maximum or a minimum.Slow Axis. The optical axis of a PMF or P

35、ZF which is aligned to the stress rods(as in PANDA or Bow-tie fiber), the stress region (as in Oval stress region fiber),or the major axis of an elliptical core fiber. For PMF to be actually polarizationmaintaining, linearly polarized light must be aligned with one of the axes,commonly the slow axis

36、. By convention, the anti-rotation key of the connectorshould be aligned with the slow axis as defined in FOCIS-4A and to be followedfor other connector types, as shown in Figure 1.Fast Axis. The optical axis of a PMF or PZF which is orthogonal to the slowaxis. See Figure 1.PandaBow TieOvalCoreOval

37、StressRegionSlow axis(Aligned WithConnector Key)FastAxisFigure 1. Types of Polarization-Maintaining FiberDevice Under Test (DUT). The specimen, or device, under test.TIA/EIA-455-20132. Normative references_The following standards contain provisions, which, through reference in this text,constitute p

38、rovisions of this Standard. At the time of publication, the editionsindicated were valid. All standards are subject to revision, and parties toagreements based on this Standard are encouraged to investigate the possibilityof applying the most recent editions of the standards indicated below. ANSI an

39、dTIA maintain registers of currently valid national standards published by them.ANSI/TIA/EIA 440-A Fiber Optic TerminologyANSI/TIA/EIA 455-A Standard Test Procedure for Fiber Optic Fibers, Cables, Transducers, Sensors, Connecting and Terminating Devices, and Other Fiber Optic ComponentsANSI/TIA/EIA

40、455-80 FOTP-80, Cut-off Wavelength MeasurementProcedureANSI/TIA/EIA 455-107A FOTP-107, Determination of Component Reflectanceor Link/System Return Los Using a Loss Test SetANSI/TIA/EIA 455-180 FOTP-180, Measurement of the optical transfercoefficients of a passive branching device (coupler)ANSI/TIA/E

41、IA 604 Fiber Optic Connector Intermateability StandardANSI/TIA/EIA 604-4A FOCIS 4A, Fiber Optic Connector IntermateabilityStandard Type FC with APC and PolarizationMaintaining RequirementsTELCORDIA GR-326-CORE Generic Specification for Single ModeConnectors and Cable Assemblies (Issue 3)_3. Apparatu

42、s_The following apparatus and equipment are required to perform this test.TIA/EIA-455-20143.1 Optical light sourceThe optical power source shall be a diode laser, either modulated orunmodulated, whose center wavelength and spectral width shall be within theparameters provided in Table 1, unless othe

43、rwise specified in the DetailSpecification. In addition, the source shall not emit more than 0.1% (-30dB) ofits optical power at wavelengths shorter than the cutoff wavelength (per FOTP-80) of any of the fibers (SMF/PMF/PZF) incorporated in the measurementapparatus.Table 1. Wavelength Requirements O

44、f Optical Power SourceNominal Wavelength Center Wavelength RMS Spectral Width1310nm 1310nm +/- 30nm 5nm1550nm 1550nm +/- 30nm 5nmThe optical power of the light source must either be stable over the duration ofthe test or normalized by means of a reference. Without a reference, theuncontrolled variat

45、ion in source power must be less than 1% (0.05 dB) duringthe measurement.The source power must be capable of meeting the dynamic range requirementsof the measurement when combined with the detector sensitivity. In addition,the power launched into the component must not be at such a high level as toi

46、nduce non-linear scattering at levels higher than 10 dB below the level of testsensitivity desired. Use of an isolator is optional, but is recommended for lasersources to ensure stable operation.The optical power source should not be a single-spectral-line laser. Single-spectral-line lasers may have

47、 a coherence length long enough to turn the testset-up into an interferometer. Additionally, if the Device Under Test (DUT) issufficiently reflective, a narrow line width source may be destabilized.3.2 Single-mode optical directional couplerThe coupler shall be fabricated from non-PMF/PZF single-mod

48、e fiber whosecore diameter, numerical aperture and cut-off wavelength most closely matchesthe PMF/PZF of the DUT. The coupler shall also be polarization insensitive toprevent any dependence on the angular position at which the DUT is connected.The directional coupler (or splitter) may be of any convenient coupling ratio if theselecting coupling ration remains stable throughout the measurementprocedure. Use of a three port (1x2