ANSI TIA EIA 455-85A-1992 Fiber Optic Cable Twist Test《光缆扭曲试验》.pdf

《ANSI TIA EIA 455-85A-1992 Fiber Optic Cable Twist Test《光缆扭曲试验》.pdf》由会员分享，可在线阅读，更多相关《ANSI TIA EIA 455-85A-1992 Fiber Optic Cable Twist Test《光缆扭曲试验》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA STANDARD FOTP-85 Fiber Optic Cable Twist Test TIA-455-85-A May 1992 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Representing the telecommunications industry in association with the Electronic Industries Alliance ANSI/TIA/EIA-455-85-A-1992Approved: May 26, 1992Reaffirmed: May 11, 1999Reaffirmed: May

2、 10, 2005Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunder

3、standings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respe

4、ct preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and

5、Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not

6、 purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Sta

7、ndards Proposal No. 3-4445-RF1, formulated under the cognizance of the TIA FO-4.2 Subcommittee on Optical Fibers and Cables).Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalo

8、g of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) or search online at http:/www.tiaonline.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A. Co

9、pyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (incl

10、uding posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiao

11、nline.org/about/faqDetail.cfm?id=18 OR Telecommunications Industry Association Standards (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards deve

12、lopment or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents

13、 and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any

14、 claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that pro

15、cedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any c

16、laims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INF

17、RINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFE

18、CTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY A

19、ND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY

20、 OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduc

21、tion or networking permitted without license from IHS-,-,-Section 1. 2. 3. 4. 5. 6. 7. 8. APPENDIX Figure 1 Figure 2 Figure 3 Table 1 Table 2 EIA TIA-455-85A 92 3234600 OS02530 227 TI-85A E“P-85 FIBER OPTIC CABLE TWIST TEST TABLE OF CONTENTS INTRODUCTION APPLICABLE DOCUMENTS APPARATUS SAMPLING AND S

22、PECIMENS PROCEDURE CALCULATIONS OR INTERPRETATION OF RESULTS DOCUMENTATION SPECIFICATION INFORMATION COMPARISON BETWEEN FOTP-85 AND IEC, ISO, AND CCITT REQUIREMENTS Cable Twisting Apparatus Cable Twisting Apparatus With Alternative Cable Twisting Apparatus Tensioning Applied With Tensioning Applied

23、Recommended Twist Lengths (LI Recommended Tensioning Loads Paqe 1 2 3 5 7 10 10 11 12 6 8 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA TIA-455-5A 92 3234bOO 0502533 163 =

24、 TIA/EA-455-85A Page 1 FOTP-85 FIBER OPTIC CABLE TWIST TEST (From EIA Standards Proposal No. 2371-A, formulated under the cognizance of TIA FO-6.4, Subcommittee on Fiber Optic Test Methods and Instrumentation, and TIA FO-6.7, Subcommittee on Fiber Optic Cables.) This FOTP is part of the series of te

25、st procedures included within Recommended Standard EIA/TIA-455. NOTE : This FOTP was originally published in FOTP-85. EIA RS-455-85 as 0 1. INTRODUION 1.1 Intent. The intent of this test is to establish the ability of a fiber optic cable (or fiber optic cable component, when appropriate) to mechanic

26、ally withstand twisting. 1.2 Measurements . observed: The following parameters may be measured or (a) (b) The number of broken fibers caused by twisting. Any change in the outer covering. (cl The change in optical measurement results caused by twisting. For a similar test for fiber optic connecting

27、devices, see FOTP- 3 6. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA TIA-455-85A 92 3234600 O502512 OTT TIA/EIA-455-85A Page 2 2. APPLICABLE DOCUMENTS specified heGein: E

28、IA/TIA-455-A The followina documents form a part of this FOTP to the extent “Standard Test Procedures for Fiber Optic Fibers, Cables, Transducers, Sensors, Connecting and Terminating Devices, and Other Fiber Optic Components IV FOTP-13 (EIA-455-13) FOTP-20 (EIA/TIA-455-20A) FOTP-36 (EIA-455-36A) FOT

29、P-46 (EIA/TIA-455-46A) FOTP-53 (EIA/TIA-455-53A) FOTP-61 (EIA/TIA-455-61) FOTP-78 (EIA/TIA-455-78A) CE1 IEC 794-1, Second Ed. Method IEC 794-1-E7 CE1 IEC 794-2, Second Ed. “Visual and Mechanical Inspection of Fiber, Cables, Connectors and/or Other Fiber Optic Devices“ “Measurement of Change in Optic

30、al Transmittance “Twist Test for Fiber Optic Connecting Devices“ “Spectral Attenuation Measurement for Long-Length, Graded-Index Optical Fibers“ “Attenuation by Substitution Measurement for Multimode Graded- Index Optical Fibers or Fiber Assemblies Used in Long Length Communications Systems“ “OTDR M

31、easurement of Fiber or Cable Attenuat ion “Spectral Attenuation Cutback Measurement for Single-Mode Optical Fi bers “Optical fibre cables, Part 1: Generic specification“ “Tors i on“ “Optical fibre cables, Part 2: Product specifications“ * in process of preparation. Pending publication of this revisi

32、on, use ANSI/EIA RS-455-20. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA TIA-455-85A 92 3234500 0502513 T3b . TIA/EIA-455-85A Page 3 3. APPARATUS The following apparatus

33、and equipment is required to perform this test: 3.1 misting Apparatus. The twisting apparatus consists essentially of two cable gripping devices or clamps, one fixed and one that can rotate, supported as appropriate, and adjustable as to distance between them. The rotating clamp is connected to suit

34、able turning equipment (e.g., a torquing lever). Any clamp supports used, the gripping devices, and the torquing equipment, shall all be such as to permit access to both ends of the cable specimen for optical testing as may be required. Suitable apparatus is illustrated in Figures 1, 2, and 3, but o

35、ther substantially equivalent apparatus may also be used. The cable gripping devices shall be such that (1) they may be tightened around the cable sufficient to prevent movement within the grip, (2) the clamps hold the cable firmly in a straight line, (3) the clamps induce neither localized twisting

36、 damage on the cable caused by the inside edge of the clamp nor undue localized concentration of pressure on the cable, and (4) the process of clamping does not induce any significant or accurately measurable attenuation increase (or no more than a negligible increase) in the specimen. 0 NOTE 1: Spl

37、it die blocks with tapered openings in various die opening sizes to accommodate varying cable diameters have been found to be suitable as clamps. The opening diameters shall be sufficient to hold the cable straight in the die without transferring the twist into the die. The die length shall be suffi

38、cient to provide adequate gripping surface. Die lengths of at least 30 mm (or 1.25 in.) have been found to provide adequate gripping surface for a small cable having a diameter equal to or less than the die length. 3.2 Tensioning Apparatus. If required by the Detail Specification and/or to minimize

39、specimen bending from a straight configuration, use weights or an appropriate loading mechanism to apply a tensile load to the cable gripping fixture (see Figures 2 and 3). Refer to Table 2 for recommended tensioning loads, 3.3 Optical Test Equipment. Use apparatus as described in FOTP-20 for measur

40、ing the change in optical transmittance (throughput) of the transmitting fibers. Alternatively, unless otherwise specified in the Detail Specification, use equipment as described in one of the following FOTPs for measuring attenuation for a particular type of fiber in the cable: Copyright Telecommun

41、ications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA TIA-455-85A 72 3234b1313 13502534 972 TIA/EIA-455-85A Page 4 - For multimode: FOTP-46, FOTP-53, or FOTP-61 - For single-mode: FOTP-61 or FOTP-78.

42、 Equipment for measuring the transmittance or attenuation shall be stable throughout the duration of a single pulse and over the period of time required to perform the measurement. Figure 1 Cable Twisting Apparatus Figure 2 Cable Twisting Apparatus with Tensioning Applied Copyright Telecommunication

43、s Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FIA TIA-455-85A 92 3234600 05025115 809 TIA/EIA-455-85A Page 5 Figure 3 Alternative Cable Twisting Apparatus With Tensioning Applied 4. SAMPLING AND SPECIME

44、NS 4.1 Specimen - General. The specimen shall be a sample of fiber optic cable having a total length sufficient to permit the appropriate clamping and twisting, long enough to permit optical measurements (if required), and as required by 4.2 and 4.3. (NOTE: Do not confuse the “total specimen length“

45、 with the “twist length. ) Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA TIA-455-5A 92 3234b00 050251b 745 TIA/EIA-455-85A Page 6 4.2 Total Specimen Length. Unless otherwi

46、se specified in the Detail Specification, the minimum total specimen length shall be as follows: 4.2.1 The total specimen shall be sufficiently long to permit the twisting of the minimum length of cable required by 4.3. 4.2.1.2 For U.S. Military applications only, the total specimen length shall als

47、o be not less than 100 times the diameter of the finished specimen cable or not less than 1 m (39 in. ) , whichever is greater. 4.2.2 When optical measurements (change in optical transmittance or attenuation) must be made, the total specimen length shall also be such that the optical loss in the fib

48、er can be effectively monitored as required by the Detail Specification or by the referenced optical measurement FOTP, or both. 4.3 Specimen Length to be Wisted. The length of the specimen O to be twisted (LI shall be as specified by the Detail Specification. 4.3.1 If not specified by the Detail Spe

49、cification, maximum twist length (LI may be selected from Table 1, following, depending upon type of cable undergoing test: Table 1 Recumended Twist Lengths (L) Cable Typ e Outside Plant Cable Twist Lengths meter (feet) 4 i 13 1 Inside Cable - Riser 2 ( 6-6 1 Inside Cable - Plenum and General Purpose 1 ( 3.3 1 Inside Cable - General Purpose Interconnect 0.3 Copyright Telecommunicatio